AcraDyne AB-C18110 User manual

10000 SE Pine St. Portland, Oregon 97216 Phone: [phone]
www.aimco-global.com
Single Charger User Manual
AB-C18110 & AB-C18220
for AcraDyne Batteries AB-B1825LI & AB-B1850LI

10000 SE Pine St. Portland, Oregon 97216 Phone: [phone]
www.aimco-global.com
2
Table of contents___________________________
Page
1. Basic information . . . . . . . . . . . . . . . . . . . . . . 3
1.1. Purpose of this document . . . . . . . . . . . . . . . . . 3
1.2. Intended use . . . . . . . . . . . . . . . . . . . . . . . . 3
1.2.1. Improper use . . . . . . . . . . . . . . . . . . . . . . . . 3
1.3. Warranty and liability . . . . . . . . . . . . . . . . . . . 3
2. Basic safety information . . . . . . . . . . . . . . . . . . 6
2.1. Observing information contained in this document . . 6
2.2. Owner responsibilities . . . . . . . . . . . . . . . . . . . 6
2.2.1. Personnel responsibilities . . . . . . . . . . . . . . . . . . 6
2.2.2. Personnel training . . . . . . . . . . . . . . . . . . . . . 6
2.3. Electrical hazards. . . . . . . . . . . . . . . . . . . . . . 6
2.3.1. Basic safety measures (must always be observed!). . . 6
2.3.2. Observing the line voltage . . . . . . . . . . . . . . . . 8
2.4.  Structuralmodications . . . . . . . . . . . . . . . . . . 8
2.5. Cleaning the tool and disposal . . . . . . . . . . . . . . 8
3. Placement into service . . . . . . . . . . . . . . . . . . 9
3.1. Operation . . . . . . . . . . . . . . . . . . . . . . . . . 9
4. Technical data . . . . . . . . . . . . . . . . . . . . . . 10
4.1. Dimensions . . . . . . . . . . . . . . . . . . . . . . . . 10
4.2. Additional characteristics . . . . . . . . . . . . . . . . 10

10000 SE Pine St. Portland, Oregon 97216 Phone: [phone]
www.aimco-global.com
10000 SE Pine St. Portland, Oregon 97216 Phone: [phone]
www.aimco-global.com 3
1. Basic information___________________________________
1.1. Purpose of this document
This information has been written with the intention of being read,
understood, and adhered to in all aspects by those who bear re-
sponsibility for this battery charger. The information contained in this
document is important for avoiding workplace mishaps and ensu-
ring problem-free operation. If, despite this, problems are encoun-
tered, then please contact us; we would be pleased to help you.
1.2. Intended use
Thetoolmayonlyusedtochargematchingbatteriesasspecied
in this manual.
!Intended use includes the following:
• Observing all information in the operating instructions, and
• Complying with the inspection and maintenance tasks
The quick charger serves to recharge the following batteries:
• AB-B1825LI & AB-B1850LI
1.2.1. Improper use
We bear no liability for damage or operating problems resulting
from noncompliance with operating instructions or improper use.
1.3. Warranty and liability
NEW TOOL AND ACCESSORY WARRANTY
Any new tool or accessory branded with the AIMCO, Uryu,
AcraDyne or Eagle Industries name, and purchased from
AIMCO, or through one of its authorized distributors or agents, is
warranted to the original buyer against defects in materials and
workmanship for a period of one (1) year* from date of delivery.
Under the terms of this warranty, AIMCO will repair or replace
any product or accessory warranted hereunder and returned
freight prepaid proving to AIMCO’s satisfaction to be defective
as a result of workmanship or materials. In order to qualify for this
warranty, written notice to AIMCO must be given immediately
upon discovery of such defect, at which time AIMCO will issue an

10000 SE Pine St. Portland, Oregon 97216 Phone: [phone]
www.aimco-global.com
4
authorization to return the tool. The defective item must be promptly
returned to an authorized AIMCO service center with all freight
charges prepaid.
REPAIRED TOOL WARRANTY
Once a tool is beyond the new product warranty period as
detailed above, AIMCO repairs are subject to the following
warranty periods: pneumatic tools: 90 days*; electric tools and
Acra-Feed: 90 days; battery tools: 30 days*; DC Electric tools: 90
days*
EXCLUSION FROM WARRANTY
This warranty is valid only on products purchased from AIMCO,
or thru its authorized distributors or agents. AIMCO shall have no
obligation pursuant to the AIMCO Warranty with respect to any
tools or accessories which in AIMCO’s sole judgment have been
altered, damaged, misused, abused, badly worn, lost or improperly
maintained. This Warranty is null and void if the customer, or any
other person other than an authorized representative of AIMCO, has
made any attempt to service or modify the tool or accessory prior
to its return to AIMCO under this Warranty.
The warranty provision with respect to each such product may
be amended by AIMCO from time to time in its sole discretion.
The liability of AIMCO hereunder shall be limited to replacing or
repairing, at its option, any products which are returned freight
prepaid to AIMCO and which AIMCO determines to be defective
as described above or, at AIMCO’s option, refunding the
purchase price of such products.
AIMCO reserves the right to make periodic changes in
constructionortooldesignatanytime.AIMCOspecically
reserves the right to make these changes without incurring any
obligation or incorporating such changes or updates in tools or
parts previously distributed.
THE AIMCO WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES,
EXPRESSED OR IMPLIED, AND AIMCO EXPRESSLY DISCLAIMS ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR

10000 SE Pine St. Portland, Oregon 97216 Phone: [phone]
www.aimco-global.com
10000 SE Pine St. Portland, Oregon 97216 Phone: [phone]
www.aimco-global.com 5
PURPOSE. THIS WARRANTY SETS FORTH THE SOLE AND EXCLUSIVE
REMEDY IN CONTRACT, TORT, STRICT LIABILITY, OR OTHERWISE.
THIS WARRANTY IS THE ONLY WARRANTY MADE BY AIMCO WITH
RESPECT TO THE GOODS DELIVERED HEREUNDER, AND MAY BE
MODIFIED OR AMENDED ONLY BY A WRITTEN INSTRUMENT SIGNED
BY A DULY AUTHORIZED OFFICER OF AIMCO.
LIMITATION OF LIABILITY
AIMCO’S LIABILITY PURSUANT TO WARRANTY OF THE PRODUCTS
COVERED HEREUNDER IS LIMITED TO REFUND OF THE PURCHASE
PRICE. IN NO EVENT SHALL AIMCO BE LIABLE FOR COSTS OF
PROCUREMENT OF SUBSTITUTE GOODS BY THE BUYER. IN NO EVENT
SHALL AIMCO BE LIABLE FOR ANY SPECIAL, CONSEQUENTIAL,
INCIDENTAL OR OTHER DAMAGES (INCLUDING WITHOUT
LIMITATION, LOSS OF PROFIT) WHETHER OR NOT AIMCO HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH LOSS, HOWEVER CAUSED,
WHETHER FOR BREACH OR REPUDIATION OF CONTRACT, BREACH
OF WARRANTY, NEGLIGENCE OR OTHERWISE. THIS EXCLUSION
ALSO INCLUDES ANY LIABILITY WHICH MAY ARISE OUT OF THIRD
PARTY CLAIMS AGAINST BUYER. THE ESSENTIAL PURPOSE OF THIS
PROVISION IS TO LIMIT THE POTENTIAL LIABILITY OF AIMCO ARISING
OUT OF THIS AGREEMENT AND/OR SALE.
Note:TheAIMCOWarrantyconfersspeciclegalrights,however
some states or jurisdictions may not allow certain exclusions or
limitations within this warranty.
* All warranty periods addressed herein are determined using a
standard shift, eight-hour work day.

10000 SE Pine St. Portland, Oregon 97216 Phone: [phone]
www.aimco-global.com
6
2.3. Electrical hazards
2.1. Information contained in this document
• A basic prerequisite for safety-compliant handling and
problem-free operation is knowledge of the basic safety
information and safety regulations.
• Also be sure to observe all local rules and regulations.
2.2. Owner responsibilities
The owner is obligated to only allow persons who are familiar
with basic work safety and accident prevention rules and who
have been briefed on proper workplace handling to work at
this workplace. The safety-conscious work of personnel must be
veriedatregularintervals.
2.2.1. Personnel responsibilities
All persons who are tasked with working at this workplace are
obligated, before beginning with work, to observe the basic
regulations covering work safety and accident prevention.
2.2.2. Personnel training
Only personnel that have been trained and briefed in advance
may work at this workplace.
Personnel responsibilities for installation, placement into service,
operation,maintenance,andrepairmustbeclearlydened.
Personnel still to be trained may only work at this workplace under
the supervision of someone who is trained and experienced.
The device is designed using state-of-the-art technology
and according to recognized safety standards.
Nonetheless, operating the device can entail the risk of
life-threatening injury to the user, third parties, or property.
The workplace is only to be used:
• For intended purposes
• If it is in proper and safe working condition
!
Only allow work to be carried out by an electrical
specialist. Regularly check the electrical equipment.
Rectify loose connections immediately.
2. Basic safety information ________________________

10000 SE Pine St. Portland, Oregon 97216 Phone: [phone]
www.aimco-global.com
10000 SE Pine St. Portland, Oregon 97216 Phone: [phone]
www.aimco-global.com 7
2.3.1. Basic safety measures (must always be observed!):
• Keep your work area in good condition
• A disorderly work area can result in an accident
• Take environmental factors into account
- Do not expose the charger station to rain.
- Do not use the charger station in a humid or wet environment.
 -Ensurethatthereissufcientillumination.
 -Donotusethechargerstationintheproximityofammable
liquids or gases.
• Keep children away
- Do not allow other persons to touch the device or cable;
keep them away from your work area.
• Use the correct device
- Do not use the charger station for purposes and work for
which it was not intended.
• Do not misuse the cable
- Do not pull the plug out of the power socket by the cable.
- Protect the cable against heat, oil and sharp edges.
• Maintain your device with care
- Keep charger station clean for better and safer operation.
- Regularly inspect the cable and, in case of damage, have it
 replacedbyaqualiedexpert.Keepthedevicedryand
free of oil and grease.
• Pull out the main power plug when not in use and before
maintenance.
• Inspect your device for damage
- Before using the charger station, the protective equipment
or damaged parts must be tested to ensure problem-free
functionality according to their intended purpose.
- Check whether moving parts function properly and determine
whether or not they jam, whether any parts are broken, whether
  allotherpartsareawless,arecorrectlyinstalledandwhetherall
  factorsthatcouldinuenceoperationofthedeviceareOK.
- Damaged protection equipment, switches, and other parts
should be properly repaired or replaced by a customer
service center.
• Protect yourself against electric shock
- Avoid any body contact with grounded parts, e.g. pipes,
radiators, stoves, refrigerators.
• Replacement parts
- For repair and maintenance, only original replacement parts
obtained from AIMCO may be used.

10000 SE Pine St. Portland, Oregon 97216 Phone: [phone]
www.aimco-global.com
8
EXPLOSION HAZARD!
Do not open batteries or the battery charger, and
protectthemagainstjolts,heat,andre.Donottossused
batteriesinareordisposeoftheminregulargarbage.
• Defective batteries
Do not use the battery charger with any defective batteries
and vice versa.
• Symbols
Observe the symbols marked on the power rating plate of the
battery charger.
• Dismantling
Do not disassemble either the battery or the battery charger.
Protect the battery charger against metal objects, as
there is a risk of short circuiting. The ventilation slits on
the battery charger must also be protected against
metal and/or metal shavings.
2.3.2. Observing the line voltage
CAUTION!
Adhere to the correct line voltage.
Usingahighervoltagethanisspeciedcanleadto
serious injuries of the operator and cause damage to
the device itself. In case of doubt, do not connect the
deviceandrstverifythelinevoltage.
2.4. Structural modications
Nochanges,extensionsormodicationsmaybecarriedouton
the device without the approval of the manufacturer.
AllmodicationsrequirewrittenconrmationbyAIMCO.
Immediatelyreplacedevicepartsthatarenotinawless
condition.
Use only original replacement parts.
!
2.5. Cleaning and disposal of the device
Handle and dispose of the substances and materials utilized in a
proper manner, especially when cleaning with solvents.

10000 SE Pine St. Portland, Oregon 97216 Phone: [phone]
www.aimco-global.com
10000 SE Pine St. Portland, Oregon 97216 Phone: [phone]
www.aimco-global.com 9
3. Placement into service ____________________________
3.1. Operation
GreenLEDashing (right LED): Battery is
too hot or cold. Preferably charge the
battery at room temperature.
RedLEDashing (right LED): Battery is
damaged. Remove the battery and
give it to the repair station or change
it. A battery may only be repaired by
professionals. Opening the casing could
result in an electrical shock.
Red LED on (right LED): Battery is charging.
Green LED on (right LED): Battery is fully
charged.
Red LED on (left LED): Charger is connected to power.
Red LEDashing(leftLED):Chargerismalfunctioning.Don´tcharge
other batteries on this charger — they could be damaged or
defective after charging. Change the charger or have it repaired by
a professional. Opening the casing could result in an electrical shock.
CAUTION! When charging two batteries consecutively,
allow the charger to cool down between charges.
A fully charged battery may reside in the plugged charger
following full charge levels. If the battery is fully charged
onthecharger,nochargingcurrentows;thecharging
process has stopped.
Only use the charger station in dry rooms.
All ventilation slits must be unobstructed. Place the device as
far away as possible from exposure to heat and solar energy,
as an ambient temperature of more than 95° F (35° C) can
lead to substantially longer charging times.
!
Priortoconnectingthedevice,obsaervespecicationsonthe
type plate concerning line voltage, frequency, and current
consumption. Once the main power cable has been inserted
in the power socket, the charger station is operationally ready.
Nothing else needs to be switched on.
!
CAUTION! Always
ensure correct
polarity +/-.
!

10000 SE Pine St. Portland, Oregon 97216 Phone: [phone]
www.aimco-global.com
10
AB-C18220 AB-C18110
Connection 220 – 240V / 50-60 Hz 110V / 50-60 Hz
Charging current per box 3.0 A 3.0 A
Output 18 V 18 V
Discharge current 30 mA 30 mA
Charging time 25-80 minutes 25-80 minutes
Switch-off criteria ∆U,temperature
termination
∆U,
temperature
termination
4.1. Dimensions
AB-C18220 & AB-C18110
Size (W x H x D ): 85.5 x 106.8 x 152.5 mm
Weight: ca. 0.5 kg
4.2. Additional characteristics
- Quick charger for 18 V Li-Ion battery pack
AB-B1825LI & AB-B1850LI
- Battery defect detection
- Battery surge protection
- Microprocessor-controlled charging
Charging time depending on the capacity of the battery
- Automatic voltage detection
4. Technical data_____________________________________