ACS MIIX 3-1030 User manual
www.acs.com.hk
User Manual V1.00
ACR3x
Mobile Card Reader
ACR3x – User Manual [email protected]
Version 1.00 www.acs.com.hk
Page 2 of 34
Table of Contents
1.0. Introduction ............................................................................................................... 3
2.0. Installing the demo application ............................................................................... 4
2.1. For iOS...................................................................................................................................4
2.2. For Android™ ........................................................................................................................5
3.0. Using the application with ACR31 mobile card reader.......................................... 9
3.1. Using a magnetic stripe card .................................................................................................9
3.1.1. Getting the firmware version .......................................................................................11
3.1.2. Getting the battery status............................................................................................12
3.1.3. Setting the sleep timeout ............................................................................................13
4.0. Using the application with ACR32 mobile card reader........................................ 20
4.1. Using a magnetic stripe card ...............................................................................................20
4.2. Using a contact smart card (ICC) ........................................................................................20
4.2.1. Changing the timeout setting ......................................................................................21
4.2.2. Getting the ATR ..........................................................................................................22
4.2.3. Transmitting command APDU ....................................................................................24
4.2.4. Executing a command ................................................................................................26
5.0. Using the application with ACR35 mobile card reader........................................ 28
5.1. Using a magnetic stripe card ...............................................................................................28
5.2. Using a contactless smart card (PICC) ...............................................................................28
5.2.1. Changing the timeout setting ......................................................................................29
5.2.2. Getting the ATR ..........................................................................................................30
5.2.3. Transmitting command APDU ....................................................................................32
5.2.4. Configuring radio frequency........................................................................................34
ACR3x – User Manual [email protected]
Version 1.00 www.acs.com.hk
Page 3 of 34
1.0.Introduction
The ACR3x Mobile Card Reader serves as an interface for the communication between a mobile
device and a magnetic stripe card or smart card. Different types of cards have different
communication protocols which, in most cases, prevent direct communication between a card and a
mobile device.The ACR3x Mobile Card Reader establishes a uniform interface from the mobile device
to the card. By taking care of the card’s particulars, it releases the computer software programmer
from being responsible with the operations’ technical details, which in many cases, are not relevant to
the implementation of the card system.
This document contains information regarding the installation and workflow of demo included in the
Android™ and iOS library of the ACR3x Mobile Card Reader.
ACR3x – User Manual [email protected]
Version 1.00 www.acs.com.hk
Page 4 of 34
2.0.Installing the demo application
2.1. For iOS
1. Download the device library from the link below:
http://acs.com.hk/en/products/227/acr31-swipe-card-reader/.
2. Using XCode application, open the AudioJackDemo.xcodeproj.
3. Transfer the AudioJackDemo.xcodeproj to your mobile device by choosing your mobile device
and then clicking the play button.
Note: Make sure that your mobile device is connected to your computer.
ACR3x – User Manual [email protected]
Version 1.00 www.acs.com.hk
Page 5 of 34
2.2. For Android™
1. Connect your mobile device to the computer.
2. In the internal storage of your device, create a folder where the ACR31 Android demo will be
placed.
3. Download the ACR31 Android library from the link below:
http://www.acs.com.hk/index.php?pid=product&prod_sections=0&id=ACR31
ACR3x – User Manual [email protected]
Version 1.00 www.acs.com.hk
Page 6 of 34
4. Copy the AudioJackDemo.apk file from the downloaded ACR31 Android library into the
previously created folder.
5. Disconnect your mobile device from the computer, and then locate the AudioJackDemo.apk
using a file manager application.
ACR3x – User Manual [email protected]
Version 1.00 www.acs.com.hk
Page 7 of 34
6. Tap the AudioJackDemo.apk file to start the installation process.
7. Complete the action using Package Installer.
ACR3x – User Manual [email protected]
Version 1.00 www.acs.com.hk
Page 8 of 34
8. A prompt will ask for hardware control access. Tap Install to proceed.
9. Once the installation is complete, you may now open the AJ Demo application.
ACR3x – User Manual [email protected]
Version 1.00 www.acs.com.hk
Page 9 of 34
3.0.Using the application with ACR31 mobile card reader
This section provides a simple step-by-step procedure on how to use the ACR31 mobile card reader
with a magnetic stripe card using the AudioJack demo application.
3.1. Using a magnetic stripe card
1. Connect the ACR31 to the audio port of your mobile device.
Note: Make sure that the volume is set to its maximum level to allow communication between
the ACR31 reader and your mobile device.
2. Open the AJ Demo application.
3. The reader is in sleep mode by default. Tap Reset to wake up the reader.
Note: By default, the reader will enter sleep mode if there is no operation after 4 seconds.
ACR3x – User Manual [email protected]
Version 1.00 www.acs.com.hk
Page 10 of 34
4. Swipe your magnetic stripe card to the reader. The reader and card details will be displayed
on the screen.
5. Tap About reader to know more about the firmware version, battery status and sleep
timeout.
ACR3x – User Manual [email protected]
Version 1.00 www.acs.com.hk
Page 11 of 34
3.1.1. Getting the firmware version
To get the reader’s firmware version:
1. Go to About reader, and then tap Get firmware version.
ACR3x – User Manual [email protected]
Version 1.00 www.acs.com.hk
Page 12 of 34
3.1.2. Getting the battery status
To get the battery status:
1. Go to About reader, and then tap Get status.
ACR3x – User Manual [email protected]
Version 1.00 www.acs.com.hk
Page 13 of 34
3.1.3. Setting the sleep timeout
To set the sleep timeout:
1. Go to About reader, and then tap Sleep timeout.
2. Enter a value between 4 and 20, and then tap OK.
ACR3x – User Manual [email protected]
Version 1.00 www.acs.com.hk
Page 14 of 34
3.1.3.1. Customizing ID
To change the Custom ID:
1. Go to Reader ID, and then tap Set custom ID.
2. Type in your preferred ID text, and then tap OK.
ACR3x – User Manual [email protected]
Version 1.00 www.acs.com.hk
Page 15 of 34
3.1.3.2. Getting the Device ID
To get the Device ID:
1. Go to Reader ID, and then tap Get device ID.
ACR3x – User Manual [email protected]
Version 1.00 www.acs.com.hk
Page 16 of 34
3.1.3.3. Changing the master key
To change the master key:
1. Go to Cryptographic keys, and then tap Master key.
2. Type in your preferred value (in hexadecimal format), and then tap OK.
ACR3x – User Manual [email protected]
Version 1.00 www.acs.com.hk
Page 17 of 34
3. To set the keys back to its default value, tap Use default key.
ACR3x – User Manual [email protected]
Version 1.00 www.acs.com.hk
Page 18 of 34
3.1.3.4. Changing the AES key
To change the AES key:
1. Go to Cryptographic keys, and then tap AES Key.
2. Type in your preferred value (in hexadecimal format), and then tap OK.
ACR3x – User Manual [email protected]
Version 1.00 www.acs.com.hk
Page 19 of 34
3. To set the keys back to its default state, tap Use default key.
ACR3x – User Manual [email protected]
Version 1.00 www.acs.com.hk
Page 20 of 34
4.0.Using the application with ACR32 mobile card reader
This section provides a simple step-by-step procedure on how to use the ACR32 mobile card reader
with various card types using the AudioJack demo application.
4.1. Using a magnetic stripe card
For instructions on how to use a magnetic stripe card with ACR32, please refer to Section 3.1 of this
document.
4.2. Using a contact smart card (ICC)
1. Connect the ACR32 to the audio port of your mobile device.
Note: Make sure that the volume is set to its maximum level to allow communication between
the ACR32 reader and your mobile device.
2. Tap ICC to explore the functions of a contact smart card.
This manual suits for next models
1
Table of contents
Other ACS Card Reader manuals
