ACT SMART CONTROLLER User manual

Operating & Installation Instructions
for ACTsmart Product Range
18-00052

ACT mart Operating and In tallation Manual Rev. 1.2
2
Contents
ORDERING INFORMATION ............................................................................................2
INSTALLATION NOTES ....................................................................................................3
IMPORTANT ........................................................................................................................3
PRODUCT SPECIFICATION ............................................................................................3
30 SECOND PROGRAMMING GUIDE ..........................................................................4
PROGRAMMING SUMMARY ..........................................................................................5
ACTSMART OPERATION ................................................................................................6
ACTSMART PROGRAMMING ........................................................................................6
Adding a Card Batch: ..........................................................................................7
Deleting a Card Batch:..........................................................................................7
Adding a P N: ......................................................................................................7
Deleting a P N: ....................................................................................................7
Adding a Card and P N: ......................................................................................7
Deleting a Card and P N:......................................................................................7
Adding a Card Batch using the keypad: ..............................................................8
Deleting a Card or Card and P N using the keypad:............................................8
Set Door Relay Time: ..........................................................................................8
Set Door Ajar Time:..............................................................................................8
Set Guest Buzzer Time: ........................................................................................8
Change Programming Code: ................................................................................8
Change Number of P N Digits: ............................................................................8
Programming ACTsmart Options: ........................................................................9
Setting Programmable nput Function: ..............................................................10
Setting AUX /O 1 Function:..............................................................................10
Setting AUX /O 2 Function:..............................................................................10
/O Function Codes:............................................................................................10
Quick O Setup: ..................................................................................................11
PROGRAMMING A NET ORK SYSTEM ..................................................................12
Assign Door Numbers: ......................................................................................12
Find Door Number: ............................................................................................13
Find All Door Numbers: ....................................................................................13
RESTORING FACTORY DEFAULTS ............................................................................13
PROGRAMMING ACTSMART PROX ONLY ..............................................................13
Adding a Card Batch to the Network:................................................................14
Deleting Batch Cards from the Network: ..........................................................14
Deleting ndividual Card (Require Card Above): ..............................................14
Programming the Door Relay Time: ..................................................................14
Default ACTsmart:..............................................................................................14
USER LIST..........................................................................................................................20
Ordering Informa ion
Proximity reader ACTsmart 1070
P N & Proximity reader ACTsmart 1080
P N Only reader ACTsmart 1090
Proximity Fob H D Fob-B or H D Fob site coded
Proximity SO Card H D SO Prox-B or H D SO Prox site coded
Proximity Half Shell Card H D Prox Card 11-B or H D Prox Card 11 site coded
Proximity & Mag Stripe Card H D Duo Prox-B or H D Duo Prox site coded

ACT mart Operating and In tallation Manual Rev. 1.2
3
Ins alla ion No es
• Remember to Factory Default the ACTsmart before programming
• Remember to place the supplied varistor across the terminals of the door strike coil to protect the relay
contacts
• Don’t mount the ACTsmart Prox units near RF sources (Eg mobile phones, radio transmitters,
computer monitors) or metal surfaces.
• Remember that theACTsmart P N and Prox units default to Card operation. Card and P N operation
must be programmed in. (See Programming ACTsmart Options, Options 39, 40 and 41).
• Don’t power the unit from a switch-mode power supply. Use a linear regulated power supply.
• Never use the on-board relay to switchAC mains voltage.An external relay, electrically isolated from
the ACTsmart should be used for this purpose
• Remember to change the programming code.
• Don’t power the ACTsmart from an AC power supply on a networked system. An AC power supply
may only be used on a standalone ACTsmart.
•The ACTsmart version is not compatible with the ACTsmart2. The cards and fobs for one
version will not work on the other. The ACTsmart and ACTsmart2 devices may NOT be
networked together.
Impor an
As with any Access Control system, always ensure there is an alternate means of escape in the event of
the unit failing to operate due to power loss or in the event of fire.
Produc Specifica ion
Number of Users 500 Users
Supply Voltage 12 - 24 V DC (linear PSU) or AC (standalone only)
Current Consumption 52mA (nominal), 100mA (maximum)
Output Current Sink 100mA
Operating Temperature -10 to +50 degrees C
Door Open Time 0 - 255 seconds
Max. ACTsmarts per network 8
Length of network 1.4 km maximum
Relay Contact Rating 5A / 38Vac
Programmable Inputs 1
Programmable Input/Outputs 2
Controller Size Flush Mount (WxHxD,mm): 100 x 110 x 20 mm
Surface Mount (WxHxD,mm): 100 x 110 x 35 mm
Controller eight 200 grams
ater Resistance High P67
Construction Rugged Polycarbonate housing with stainless steel keys
and potted electronics.

ACT mart Operating and In tallation Manual Rev. 1.2
4
30 Second Programming Guide
(For typical Standalone System)
1. Enter Programming Mode.
Press ✘button followed by the programming code (default is 9999)
The LED will flash amber.
2. Add a Batch of Cards
Press 10, then present the first card in the batch followed by the last card in the batch.
Press ✔button to complete.
3. Set Desired Door Relay Active Time
Press 20, and then enter the desired number of seconds from 000-255 (three digits with
leading zeros). Press ✔button to complete.
4. Change Programming code
Press 23, then enter new 4-digit programming code.
5. Exit Programming Mode
Press the ✘button. The LED turns red.
The ACTsmart is now ready for normal use.
Note: The ACTsmart may be returned to its factory default condition at any time by entering the
programming mode and pressing 80 followed by the ✔button.
For information on programming the advanced features and networking the ACTsmart range, please
refer to the complete programming guide.
Unit C1, South City Busin ss C ntr ,
Tallaght, Dublin 24, Ir land.
T l: 353-1-4662570 Fax: [phone] UK Locall: 0845 300 5204
W b: http://www.acc sscontrol.i E-mail: sal s@ acc sscontrol.i
Copyright ©2008 Access Control Technology Ltd.

ACT mart Operating and In tallation Manual Rev. 1.2
5
Programming Summary
10 Add Card Batch
11 Delete Card Batch
12 Add P N
13 Delete P N
14 Add Card and P N
15 Delete Card and P N
16 Add Card Batch using keypad
17 Delete Card and P N using keypad
20 Set Door Relay Time 5 seconds
21 Set Door Ajar Time 30 seconds
22 Set Guest Buzzer Time 2 seconds
23 Change Programming Code 9999
24 Change Number of P N Digits 4
30 Door Chime Off
31 Silent Operation Off
32 Lock-saver (Anti Tailgating) Off
33 Toggle Off
34 Door Forced Alarm On
35 Door Ajar Alarm On
36 Guest Button On
37 Duress Codes Off
38 Network Master Off
39 Card and P N Off
40 Card or P N Off
41 Card and any P N Off
50 Set Programmable nput Door Release Button
51 Set AUX /O 1 Door Contact
52 Set AUX /O 2 Door Alarm
53 Quick /O Setup
60 Assign Door Numbers
61 Find Door Number
62 Find Door Numbers
80 Default Unit
Code Function Default

ACT mart Operating and In tallation Manual Rev. 1.2
6
ACTsmar Opera ion
The ACTsmart family consists of Proximity Only (ACTSmart 1070), Pin and Proximity (ACTsmart
1080) and P N Only (ACTsmart 1090) units. Each ACTsmart can operate in standalone mode. Up to
8 ACTsmart devices can be connected on a RS485 network. The ACTsmart supports 500 users. Each
unit is contained in a rugged polycarbonate housing, with stainless steel keys and potted electronics,
allowing for indoor and outdoor installation.
Programming the unit is achieved via keys and feedback through the unit LED and the buzzer. For
quick and easy installation, the ACTsmart has a default configuration, which is suitable for most
installations requiring only the Programming Code to be changed, and the cards programmed into the
system. Using the Card Batch method, cards can be programmed into the ACTsmart very quickly.
ACT recommends that the user keep track of the Cardholders and P N users on the system by using
the User List at the end of the manual. Make copies of this sheet and enter all User details on it. This
will allow users to be deleted later on, even if a card is lost or a user forgets their P N code.Additional
User Lists can be downloaded from the resource section of our website at www.accesscontrol.ie
To improve security, P N codes may be up to 8 digits in length. Normally only card users are allowed
access through theACTsmart P N and Prox unit. For maximum security, the unit may be programmed
to require all users to enter a P N code after presenting a card. For lower security applications, another
programming options allows access to P N only users. A duress code feature is also available
The built-in inputs and outputs are programmable, allowing theACTsmart to be used in a wide variety
of applications from simple door access, to cash offices and fire exits. Each unit also has built-in
tamper monitoring for improved security.
ACTsmar Programming
Press the ✘button followed by the programming code (initially 9999). The LED will flash amber
while in programming mode. f ✘is pressed at any time or no key is pressed within 30 seconds,
programming mode is exited. f the LED flashes green during programming, then a card presentation
is expected. f the LED flashes red, then a keypress is expected. f the ACTsmart is busy performing
a task, (Eg. Defaulting memory, adding cards), the buzzer will sound an elongated tone.
Note: n most Programming Menus there is a step that is marked (optional)*. This setting only applies
toaNetworked System (see Programming a Network System).

Add ng a Card Batch:
Step Keypad Entry Operation
1 11 Delete Card Batch
2 Present Card First card in Batch (lowest number card)
3 Present Card Last Card in Batch (highest number card)
4 Enter 1-8, (optional)* Select each door this batch deleted from
5 Press ✔End delete card batch -
Note: the buzzer will sound while cards are deleted from memory.
Step Keypad Entry Operation
1 14 Add Card and P N (Make sure Option 39 is set on P N and Prox units.)
2 Present Card
3 0001-9999 4 - 8 digit P N code
4 1-8 (optional)* Select each door this Card & P N is valid for
5 Press ✔End programming Card and P Ns
ACT mart Operating and In tallation Manual Rev. 1.2
7
Step Keypad Entry Operation
1 12 Add P Ns (Make sure Option 40 is set on P N and Prox units.)
2 0001-9999 4 - 8 digit P N code
3 1-8, (optional)* Select each door this P N is valid for
4 Press ✔End programming P Ns
Step Keypad Entry Operation
1 13 Delete P Ns
2 0001-9999 4 - 8 digit P N code
3 1-8, (optional)* Select each door this P N is deleted from
4 Press ✔End deleting P Ns
Step Keypad Entry Operation
1 15 Delete Card and P N
2 Present Card
3 1-8, (optional)* Select each door this Card & P N is deleted from
4 Press ✔End deleting Card and P Ns
Delet ng a Card Batch:
Add ng a PIN:
Delet ng a PIN:
Add ng a Card and PIN:
Delet ng a Card and PIN:
Step Keypad Entry Operation
1 10 Add Card Batch
2 Present Card First card in Batch (lowest number card)
3 Present Card Last Card in Batch (highest number card)
4 Enter 1-8, (optional)* Select each door this batch enabled for
5 Press ✔End programming card batch -
Note: the buzzer will sound while cards are loaded into memory.

ACT mart Operating and In tallation Manual Rev. 1.2
8
Add ng a Card Batch us ng the keypad:
Step Keypad Entry Operation
1 16 Add Card Batch
2 Enter 10-digit card 10-digit First Card number with leading zeros.
number Eg. Card 54321 enter 0000054321.
3 Enter 10-digit card number Last Card number
4 1-8, (optional)* Select each door this Card is deleted from
5 Press ✔End Adding Card Batch
Delet ng a Card or Card and PIN us ng the keypad:
Step Keypad Entry Operation
1 17 Delete Card or Card and P N
2 Enter 10-digit card number 10-digit Card number with leading zeros.
Eg. Card 54321 enter 0000054321.
3 1-8, (optional)* Select each door this Card is deleted from
4 Press ✔End deleting Card (Card and P N)
Step Keypad Entry Operation
1 20 Set Door Relay Time - (default 5 seconds)
2 Enter 3digit time 000-255 seconds - (leading zeros required). Eg. 009 for 9 seconds
3 1-8 (optional)* Select each door this timer is set for
4 Press ✔End setting Door Relay Timer
Set Door Relay T me:
Step Keypad Entry Operation
1 21 Set Door Ajar Time - (default 30 seconds)
2 Enter 3digit time 000-255 seconds - (leading zeros required).
3 1-8 (optional)* Select each door this timer is set for
4 Press ✔End setting Door Ajar Time
Set Door Ajar T me:
Set Guest Buzzer T me:
Step Keypad Entry Operation
1 22 Set Guest Buzzer Time - (default 2 seconds)
2 Enter 3digit time 000-255 seconds - (leading zeros required).
3 1-8 (optional)* Select each door this timer is set for
4 Press ✔End setting Guest Buzzer Time
Change Programm ng Code:
Step Keypad Entry Operation
1 23 Change Programming code
2 0001-9999 New 4 - 8 digit programming code
Change Number of PIN D g ts:
Step Keypad Entry Operation
1 24 Change Number of P N digits
2 4-8 Select number of P N digits in range 4 to 8. When set, the codes require
leading zeros Eg. Code 9999 becomes 009999 for 6 digits.

Option Function Default Operation
30 Door Chime Off When set, whenever the door contact is opened, the built-in buzzer
makes a chime sound and the buzzer output activates for 2 seconds
31 Silent Operation Off When set, the keypad operates silently, that is no audible tones
(key-presses or confirm tones) are produced from the built-in
buzzer
32 Lock-saver Off When set, and when the door relay is active (following a valid code
(Anti Tailgating) or button release), the door relay timer is truncated to 2 seconds
when the door contact opens. This ensures that irrespective of
programmed relay time, the door will be locked as soon as it
closes, and any person following will have to enter a code.
33 Toggle Off When set, the door relay toggles for each valid entry. The green
LED flashes when the door is toggled open.
34 Door Forced Alarm On When set, the buzzer output/ door alarm output is activated if the
door contact opens when the door is locked. The output is
deactivated when a valid card or P N is next entered. This is useful
for monitoring fire doors etc.
35 Door Ajar Alarm On When set, and the door contact has been open for longer than the
time programmed into the door ajar timer, the buzzer output/ door
alarm output is activated. Closing the door and presenting a valid
card or entering a valid P N deactivates the output.
36 Guest Button On When set, (default) and when the ✔key on the keypad is pressed,
the buzzer output is activated for the duration programmed in the
guest buzzer timer.
37 Duress Codes Off When set, and when a duress P N is entered, the door is opened
normally and the Door Alarm output activated. A duress P N is
any valid P N with one added to last digit ie P N code of 6799
would have a duress code of 6800. The output will be reset when a
valid user enters. When the duress option is set, avoid using P Ns
that are different by 1.
38 Network Master Off Set one device on the network to be the Master.
39 Card and P N Off When set, only Card and P N users are admitted. This is only valid
for ACTsmart P N and Prox units.
40 Card or P N Off When set, either a valid Card or valid P N will open the door. This
is only valid for ACTsmart P N and Prox units.
41 Card and any P N Off n this mode, a valid card and any valid P N code will open the
door. This is only valid for ACTsmart P N and Prox units. This
mode allows all users to have a common P N code to use with their
cards.
ACT mart Operating and In tallation Manual Rev. 1.2
9
Programm ng ACTsmart Opt ons:
Step Keypad Entry Operation
1 30-41 Select Option Number
2 0 or 1 0=Off, 1= On
3 1-8, (optional)* Select each door this option is set for
4 Press ✔End setting options

ACT mart Operating and In tallation Manual Rev. 1.2
10
Sett ng Programmable Input Funct on:
Step Keypad Entry Operation
1 50 Set nput Function (5 - Door Release button is default)
2 0-5 Select /O Function Code (see below for explanation of codes)
3 1-8 (optional)* Select each door this function is valid for
4 Press ✔End programming nput Function
Sett ng AUX I/O 1 Funct on:
Step Keypad Entry Operation
1 51 Set AUX /O 1 Function (0 - Door Contact is default)
2 0-9 Select /O Function Code (see below for explanation of codes)
3 1-8 (optional)* Select each door this function is valid for
4 Press ✔End programming AUX /O 1
Sett ng AUX I/O 2 Funct on:
Step Keypad Entry Operation
1 52 Set AUX /O 2 Function (7 - Door Alarm is default)
2 0-9 Select /O Function Code (see below for explanation of codes)
3 1-8 (optional)* Select each door this function is valid for
4 Press ✔End programming AUX /O 2
I/O Funct on Codes:
Code Function Operation
0Door Contact nput required if you wish to monitor Door Forced or Door Ajar
1Fire Alarm Override When this input is high, the door is opened and the green LED flashes (See
Fire Alarm Override Connections diagram). f this is wired into the Master
Smart, then all doors on the network will open.
2Lock Door When this input is low, the door locks and the red LED flashes
3Card and PIN When this input is low, then only users who enter both Card and P N will be
admitted. This option is only valid on an ACTsmart P N and Prox.
4Card or PIN When this input is low, a valid Card or a valid P N will open the door. This
option is only valid on an ACTsmart P N and Prox.
5Door Release Button When this input is low, the door opens.
6Interlock This normally behaves as an input and locks the door while the input is low.
While the door relay is active or the Door Contact is open, it becomes an
active output. (See nterlock Connections diagram).
7Door Alarm This output activates while an alarm is present - A door alarm may be a door
forced, door ajar, tamper or duress.
8Follow This output follows the state of the door relay.
9Buzzer This output activates for Door Chime or Door Alarms

ACT mart Operating and In tallation Manual Rev. 1.2
11
Qu ck IO Setup:
Step Keypad Entry Operation
1 53 Set nput Output Functions (0 - is default)
2 0-9 Select a code
Prog Input AUX IO 1 AUX IO 2
0 Door Release Button Door Contact Door Alarm
1 Door Release Button Door Contact Buzzer
2 Door Release Button Door Contact nterlock
3 Door Release Button Card And P N nterlock
4 Door Release Button Fire Override nterlock
5 Door Contact Follow Door Alarm
6 Door Contact Follow Buzzer
7 Door Contact Door Alarm Buzzer
8 Fire Override nterlock Buzzer
9 Card And P N nterlock Follow
3 1-8 (optional)* Select each door this function is valid for
4 Press ✔End Quick O setup

ACT mart Operating and In tallation Manual Rev. 1.2
Programming a Ne work Sys em
Up to 8 ACTsmart devices can be connected on the network. See the ACTsmart Network nstallation
diagram to complete the necessary connections.
Programming Door Numbers
To allow some users through a door and prevent access to other users, each ACTsmart on the network
must be given a door number (1-8). An ACTsmart Proximity Only Unit requires a door number if it is
to be programmed with advanced options.
Set a Master
Set one device on the network to be the Master. This device will be used for programming the entire
network and should be a P N and Prox unit. The Master is automatically assigned door number 1. The
other ACTsmarts on the network (door numbers 2-8) are referred to as Slave Units. No programming is
allowed on a Slave (except to default it - see Restoring Factory Defaults).
After entering programming mode, enter 38 (Network Master option) then enter 1 to enable it. The rest
of the units on the network are assigned door numbers by following the procedure below:
Ass gn Door Numbers:
Assigning Users to Doors
When each ACTsmart has been given a unique door number, then users may be given access through
specific doors. n most programming menus, there is an optional step to program specific doors. For
example, when programming a Card Batch, the user may select which doors the Card Batch applies to
(Step 4 inAdding Card Batch, see above). Skip this optional step if programming is to apply to all doors
on the network.
Checking Network Programming
The door number of anyACTsmart on the network can be found using the menus below. This is a useful
check to perform to verify communications from the Master to the Slave units and to check that the Door
Numbers have been assigned correctly.
Step Keypad Entry Operation
1 60 Assign Door Numbers
2 Any ACTsmart units without a door number start to beep. The
number of beeps is determined by the door number to be
programmed. Eg. f door 5 is to be programmed, all unassigned
ACTsmarts will beep 5 times.
3 Present any H D cardor This operation should take place on the desired door number. The
pressanykeyonslaveunit ACTsmart stops beeping.
4 Repeat step 2 until all ACTsmarts have been assigned a door number.
5 Press ✔on Master End programming door numbers
12

ACT mart Operating and In tallation Manual Rev. 1.2
13
F nd Door Number:
Step Keypad Entry Operation
1 61 Find Door Numbers
2 1-8 Enter the door number to be found. The ACTsmart assigned the door
number starts to beep.
3 Press a key or present To stop the ACTsmart beeping.
a card
F nd All Door Numbers:
Step Keypad Entry Operation
1 62 Find Door Numbers
2 Press ✔Each ACTsmart beeps their door number
3 Press key or present card To stop the ACTsmart Beeping
at each ACTsmart
Adding a Slave to the Network
Another Slave can be added to the network by defaulting it first (see below) and then assigning it a
door number from the Master.
Removing a Slave from the Network
To remove a Slave unit from the network, simply disconnect it from the network.
Replacing a Slave Unit
To replace a Slave Unit, remove the old Slave from the network. Default the new Slave and add it to
the network. Assign a door number to it from the Master.
Replacing the Master Unit
f the Master Unit needs to be replaced, then replace it with a Slave unit already on the system, (as
it will have all the card/P N information), and make it the Master. Add a new, defaulted Slave to the
network in place of the swapped-out Slave. Then assign a Door numbers to the new Slave - make sure
it is the Door number of the old Slave.
Res oring Fac ory Defaul s
Enter Programming code followed by 80 followed by ✔. f this is done on the MasterACTsmart then
all ACTsmarts on the network are defaulted (including the Master). f it is done on a Slave then only
the Slave is defaulted.
f the programming code has been forgotten, power up with the tamper open (by removing the main
unit from the mounting plate or the surface mount collar), while holding down the ✘key. Release the
✘key and then enter the default Programming Code (9999).
Defaulting memory takes 3-4 seconds. During this time, the buzzer will sound an elongated tone.
Programming ACTsmar Prox Only
To program anACTsmart Prox Only device, a Programming Card must be assigned to theACTsmart.
The Programming Card may be any ACTsmart HID card. This card may not be used to gain access.
f you have received a batch of cards, it is recommended to use the first (lowest numbered) card in
the batch as the Programming Card. To set the Programming Card into the ACTsmart Prox do the
following:
1. Power up the device with LK1 removed and the tamper open (by removing the main unit

ACT mart Operating and In tallation Manual Rev. 1.2
14
Step Present Operation
1 Programming Card Add Card Batch. The Batch size is restricted to 50 cards.
2 Present Card First card in Batch
3 Present Card Last Card in Batch
from the mounting plate or the surface mount collar). Within 10 seconds of power up carry
out the following actions.
2. Present the card to the reader.
3. Take the card away from the reader for 1 second (more than 20 cm)
4. Within a further 10 seconds replace LK1. The reader will beep.
The card is now set as the Programming card. (Note: ACT recommends using an ACTsmart P N and
Prox device if a network is required).
Add ng a Card Batch to the Network:
Step Present Operation
1 Programming Card
2 Programming Card Delete Card Batch
3 Present Card First card in Batch to delete
4 Present Card Last Card in Batch to delete
Delet ng Batch Cards to the Network:
Delet ng Ind v dual Card (Requ re Card Above):
Step Present Operation
1 Programming Card
2 Programming Card
3 Programming Card
4 Programming Card Wait for 4 seconds, Buzzer sounds indicating timing... wait
required period.
5 Programming Card Buzzer stops - timer set.
Programm ng the Door Relay T me:
Default ACTsmart:
Step Present Operation
1 Programming Card
2 Programming Card
3 Programming Card Delete ndividual Card
4 Present Card Card above the card that needs to be deleted e.g. if card number
99 needs to be deleted, present card number 100
Step Present Operation
1 Programming Card
2 Programming Card
3 Programming Card
4 Programming Card
5 Programming Card Buzzer sounds intermittently and the LED flashes RED to warn
you are about to default the system
6 Present Card Default ACTsmarts. Note: This deletes the Programming Card.
(Not Programming Card)

15
ACTsmart Standalone Installation Diagram
A ess Control Te hnology, Unit C1, South City Business Centre, Tallaght, Dublin 24, Ireland.
Tel: [phone] Fax: [phone] UK Lo all: 0845 300 5204 Web: http://www.a ess ontrol.ie E-mail: sales@a ess ontrol.ie

16
ACTsmart Fire Alarm Override Connections
ACTsmart Interlock Connections
A ess Control Te hnology, Unit C1, South City Business Centre, Tallaght, Dublin 24, Ireland.
Tel: [phone] Fax: [phone] UK Lo all: 0845 300 5204 Web: http://www.a ess ontrol.ie E-mail: sales@a ess ontrol.ie

ACTsmart Network Installation Diagram
A ess Control Te hnology, Unit C1, South City Business Centre, Tallaght, Dublin 24, Ireland.
Tel: [phone] Fax: [phone] UK Lo all: 0845 300 5204 Web: http://www.a ess ontrol.ie E-mail: sales@a ess ontrol.ie
17

18
ACTsmart Mounting Instructions for Flush-Mount Unit
A ess Control Te hnology, Unit C1, South City Business Centre, Tallaght, Dublin 24, Ireland.
Tel: [phone] Fax: [phone] UK Lo all: 0845 300 5204 Web: http://www.a ess ontrol.ie E-mail: sales@a ess ontrol.ie

19
ACTsmart Mounting Instructions for Surface Mount Unit
A ess Control Te hnology, Unit C1, South City Business Centre, Tallaght, Dublin 24, Ireland.
Tel: [phone] Fax: [phone] UK Lo all: 0845 300 5204 Web: http://www.a ess ontrol.ie E-mail: sales@a ess ontrol.ie

Doors
User Lis
12345678
User Name Card Number PIN
Smar
A ess Control Te hnology, Unit C1, South City Business Centre, Tallaght, Dublin 24, Ireland.
Tel: [phone] Fax: [phone] UK Lo all: 0845 300 5204 Web: http://www.a ess ontrol.ie E-mail: sales@a ess ontrol.ie