ActionTec SBWD100B User manual

ScreenBeam Pro
Wireless Display
Receiver
- Business Edition
Model#: SBWD100B (Business Edition)
User Manual
V1.3

Table of Contents
Part I. Getting Started ...................................................................................................................... 1
1.1. Contents in the Box ....................................................................................................... 1
1.2. Meeting ScreenBeam Pro ............................................................................................. 2
1.3. System Requirements ................................................................................................... 2
1.3.1. Receiver ................................................................................................................. 2
1.3.2. Com atible Devices ............................................................................................... 2
1.3.3. Best Known Configurations (BKCs) for Intel Pro WiDi ........................................... 3
Part II. Installing the Receiver ........................................................................................................... 4
2.1. Connecting the Receiver to an HDTV ............................................................................ 4
Part III. Setting U for the First Time ................................................................................................. 6
3.1. Connecting via Windows 8.1 ......................................................................................... 6
3.2. Connecting via Intel® WiDi A (Gen 4) ...................................................................... 10
3.2.1. Adjusting the HDTV Picture ................................................................................. 13
3.2.2. Intel® WiDi Software Version Su ort ................................................................ 14
3.3. Connecting via Intel® Pro WiDi A (Gen 5) ............................................................... 15
3.4. Ti s for O timal Performance ..................................................................................... 19
Part IV. Control and Dis lay ............................................................................................................. 20
4.1. Intel Pro WiDi and Managed Meeting ......................................................................... 20
4.2. Dis lay Mode .............................................................................................................. 21
4.3. Ultra-Low Delay ........................................................................................................... 21
4.3.1. Intel WiDi (Gen 4) ................................................................................................ 22
4.4. USB over Network ....................................................................................................... 22
Part V. Device Management for IT Administrator........................................................................... 23
5.1. Log into the Local Management Web Server .............................................................. 23
5.1.1. When Autonomous GO is Enabled ...................................................................... 23
5.1.2. When Autonomous GO is Disabled ..................................................................... 24
5.1.2.1. When SSID Broadcast is Enabled ................................................................. 24
5.1.2.2. When SSID Broadcast is Disabled ................................................................ 26
5.2. Log Out ........................................................................................................................ 29
5.3. Configuring the Receiver ............................................................................................. 29
5.3.1. Renaming the Receiver ....................................................................................... 29
5.3.2. Setting u Login Username and Password for the Local Management Console . 30
5.3.3. Setting u the Receiver’s Dis lay Language ........................................................ 31
5.3.4. Setting u Managed Meetings ............................................................................ 31
5.3.5. Setting u PIN Pairing Method ............................................................................ 32
5.3.6. Managing HDMI/VGA Port Out ut ..................................................................... 33
5.3.7. Setting u WiDi Lower Bandwidth ...................................................................... 34
5.3.8. Setting u Force EDID at RTSP M3 ...................................................................... 35
5.3.9. Setting u HDCP Encry tion ................................................................................ 36
5.3.10. Setting u the VGA Com atibility Mode ............................................................. 37
5.3.11. Setting u USB Local Access ................................................................................ 37

5.3.12. Adjusting TV Screen Size ..................................................................................... 38
5.3.13. Setting u Out ut As ect Ratio........................................................................... 39
5.3.14. Setting u One Touch Play (HDMI-CEC) ............................................................... 40
5.3.15. U dating the Receiver’s Background Image ....................................................... 41
5.3.16. U dating the Receiver’s Screensaver Image ....................................................... 42
5.3.17. Setting u Network Information Dis lay on TV Screen ....................................... 43
5.3.18. Setting u Autonomous Grou Owner (AGO) ..................................................... 44
5.3.19. Setting u Communication Channel .................................................................... 45
5.3.20. Setting u Grou Owner Intent ........................................................................... 46
5.3.21. Setting u P2P Network Parameters ................................................................... 46
5.3.22. Setting u Wireless Network Parameters ........................................................... 48
5.3.23. Modifying the Receiver’s Wireless Network Name (SSID) .................................. 49
5.3.24. Setting u Broadcast Network Name .................................................................. 50
5.3.25. Setting u Wireless Connection Pro erties ........................................................ 51
5.3.26. Setting u the Receiver’s IP Address ................................................................... 52
5.3.27. S ecifying a DNS Server for the Receiver ............................................................ 53
5.3.28. S ecifying the ScreenBeam CMS for the Receiver .............................................. 54
5.3.29. Rebooting the Receiver ....................................................................................... 55
5.3.30. Resetting the Receiver to Default........................................................................ 55
5.4. U grading the Receiver ............................................................................................... 56
Part VI. FAQs and Troubleshooting .................................................................................................. 58
6.1. FAQ .............................................................................................................................. 58
6.2. Troubleshooting .......................................................................................................... 60

1
Part I. Getting Started
Thank you for your purchase of Actiontec’s ScreenBeam Pro Wireless Display Receiver
Business Edition (hereinafter refer to as “ScreenBeam Pro”).
The Receiver lets you wirelessly stream what’s on your Intel WiDi or Miracast™ compatible
device to your HDTV, including movies, videos, photos, music, and more. The Receiver frees
your eyes from a tiny screen.
The Receiver boasts some great features, including fast setup, enhanced security and IT
manageability, managed meeting (Gen 5 WiDi), smooth video playback, full 1080p HD
support, ultra-low delay, Windows 8.1 optimization, versatile compatibility, low power
consumption, and more.
With ScreenBeam Pro, it's easy to make presentations and impromptu meetings in the
conference room a breeze, as users don't need to scramble to find the right HDMI or VGA
cable in order to share a spreadsheet or presentation on the big screen. And the Managed
Meeting feature allows meeting participants to interactively share their own screens on the
big screen.
This user manual will take you through the procedures needed to install, connect to, operate,
configure, and upgrade the Receiver, and also describe a few different possible scenarios
about locating faults.
1.1. Contents in the Box
Contents in the Receiver’s package are listed below:
ScreenBeam Pro Wireless Display Receiver (SBWD100B) - Business Edition (1)
HDMI Cable (1)
HDMI-to-VGA Adapter & 3.5mm audio cable (1)
AC Power Adapter (1)
Installation Guide

2
1.2. Meeting ScreenBeam Pro
Reset Button, for resetting the device to default
Video Out Port (HDMI), connecting to HDTV/projector for video and audio output
Power Input Port, for powering the device
LED Indicator, indicating power supply status
USB Port, for firmware upgrade or USB over network application (UoIP)
1.3. System Requirements
System requirements for the receiver are shown below:
1.3.1. Receiver
To install the Receiver, you must have the following items:
A display device with one HDMI port (Type A) or one VGA port
An available power outlet
1.3.2. Compatible Devices
The Receiver is compatible with the following devices:
Tablets, Ultrabook™ devices, and 2-in-1 devices with the latest Intel® Core™ vPro™
processors and Intel WiDi 5 (or higher)
Tablets, Laptops, and Notebooks with Intel WiDi 4 (or higher)*
Wi-Fi Certified Miracast™ devices with Windows 8.1*
* Note: Recommended devices with Intel Dual-Band Wireless-AC or Wireless-N models (7260 or 7265)

3
1.3.3. Best Known Configurations (BKCs) for Intel Pro WiDi
For o timal ex erience with Intel Pro WiDi, we recommend to u date your system drivers and Intel
WiDi a lication to the latest versions rovided by Intel. You can find the latest version by visiting
Intel’s wireless dis lay su ort website
htt ://www.intel.com/ /en_US/su ort/highlights/wireless/wireless-dis lay/
•4th Gen or Higher Intel Core vPro* Platform with pGFX
•Core m, I5, or i7 with vPro
•Graphics Package v15.36.x.x
•Wireless Driver v10.18.x.x
•Intel WiDi App v5.1.x.x

4
Part II. Installing the Receiver
This chapter explains how to connect the Receiver to an HDTV. Make sure you have all the
contents from the Receiver’s package available before starting.
2.1. Connecting the Receiver to an HDTV
It is quite easy and fast to set up the Receiver. You can complete the connection in just one
minute.
To connect the Receiver to an HDTV:
1. Get the Receiver, AC power adapter, and HDMI cable from the Receiver’s package.
2. Plug one end of the supplied HDMI cable into the HDMI port (Video Out) on the Receiver,
and the other end into an available HDMI port on the HDTV.
3. Plug the connector of the power cord to the Receiver’s power input port labeled "5V DC",
and plug the power adapter to a power outlet.
When Steps 1, 2, and 3 are complete, the hardware should be connected as shown in
the figure below:
4. Turn on the HDTV and set it to display the input from the correct HDMI port (the one you
have plugged into in Step 2).
5. Verify that the “Ready to connect” screen appears on the HDTV.

5
The Receiver is connected to the HDTV, and it is ready for use.
Note: Connections to other display devices are similar.

6
Part III. Setting Up for the First
Time
This chapter explains how to connect ScreenBeam Pro for the first time to the source device.
There are three source device options: Intel WiDi (Intel Pro WiDi), Windows 8.1, and
Miracast™.
For Windows 8.1 devices, please proceed to Section “Error! Reference source not found.”;
For Windows 7/8 devices (Gen 4 WiDi), please proceed to Section “Connecting via Intel®
WiDi App (Gen 4)”;
For Intel Pro WiDi (Gen 5) devices, please proceed to Section “Connecting via Intel® Pro
WiDi App (Gen 5)”.
3.1. Connecting via Windows 8.1
This section explains how to connect a device running Windows 8.1 to ScreenBeam Pro.
1. From the Windows desktop, go to the Charms menu and select Devices to open the
Devices menu. You can also use the shortcut keys, Windows logo + K.
2. From the Devices menu, click Project.

7
3. From the Project menu, select Add a wireless display. Windows will search for
available devices.
Note: If you are running Windows 8.1 and the screens above do not appear, go to
http://www.actiontec.com/widi81 for the latest software update. Or, you can update your
Windows 8.1 via the Windows Update application.
4. Select your receiver from the device list.
5. A PIN entry box is displayed on the screen of your Windows 8.1 device. And you can
see a PIN code and the host name (QA-PC01 in this example) of the connecting device
displayed on the HDTV. Type the PIN in the PIN entry box and click Next to continue.

8
Note: You should obtain the security PIN from your network administrator if no PIN is
displayed on the connected display device.
6. The HDTV displays messages to show the status of the connection.

9
7. The device has connected to the Receiver. And the device’s screen is displayed on the
HDTV.
Note: Intel Pro WiDi will run automatically if your device is compatible with Intel Pro WiDi
and has the app installed.

10
3.2. Connecting via Intel® WiDi App (Gen 4)
Note: Connection using Intel WiDi (4.x.x.x) is available when the receiver’s AGO feature is
disabled. Refer to Section Error! Reference source not found.Error! Reference source not
found. for details about AGO.
This section explains how to connect a device running Intel's WiDi application to the receiver.
Follow the procedure below to connect your device to the Receiver:
1. Launch the Intel Wireless Display application on the device. To find the application, go
to Windows Search on the device and search for “Intel WiDi”.
2. The Intel WiDi application scans for available receivers automatically. Select your
receiver and click Connect. (The “Connect Automatically” checkbox is optional.)
Note: If your receiver is not found, you can click the Scan button to scan again.
3. A PIN entry box is displayed on the screen of the WiDi device. And you can see a PIN
code and the host name (QA-PC01 in this example) of the connecting device displayed
on the HDTV. Type the PIN in the PIN entry box on the WiDi device, and then click
Continue.

11
Note: You should obtain the security PIN from your network administrator if no PIN is
displayed on the connected display device.

12
4. The HDTV displays messages to show the status of the connection.

13
5. A "Connection Successful" screen appears on the device's screen. Click Finished,
and the device’s screen is displayed on the HDTV.
3.2.1. Adjusting the HDTV Picture
If edges of the device screen cannot be seen on the HDTV or you can see black edges, you
can adjust the cropping settings.
Follow the steps below to adjust cropping:
1. Go to the Intel WiDi application and click the Settings button to open the Settings page.
2. Go to the "Picture and Sound" section, and select “Adjust cropping”.

14
3. Adjust the HDTV picture by clicking “+”(plus) or “-”(minus).
3.2.2. Intel® WiDi Software Version Support
Make sure the device supports Intel Wireless Display (WiDi) software version 3.5 or higher.
To find out which version of Intel WiDi the device is running, launch the Intel WiDi
application and click the Help button, and then navigate to the "About Intel
®
WiDi" section.
To obtain the latest Intel WiDi software and drivers, go to:
http://www.intel.com/go/wirelessdisplayupdate; or directly click the Check Intel
®
WiDi
website for updates link on the page.

15
3.3. Connecting via Intel® Pro WiDi App (Gen 5)
ScreenBeam Pro supports Managed Meetings, which is only available with Intel® Pro WiDi.
To use this feature, ScreenBeam Pro must enable the AGO feature. In this case, Intel WiDi
(4.x.x.x) can’t connect to ScreenBeam Pro.
Note:
To install Intel® Pro WiDi, you need a compatible Haswell system (Intel® Core ™ vPro ™
processor).
For details about AGO, refer to Section Error! Reference source not found.Error!
Reference source not found..
Follow the procedure below to connect your device to ScreenBeam Pro:
1. Launch the Intel® Pro WiDi application on the device.
2. The Intel® Pro WiDi application scans for available receivers automatically. Select your
receiver to start the connection procedure.
Note: If your receiver is not found, you can click the Scan button to scan again.

16
3. A PIN entry box is displayed on the screen of the WiDi device. And you can see a PIN
code and the host name (QA-PC01 in this example) of the connecting device displayed
on the HDTV. Type the PIN in the PIN entry box on the WiDi device, and then click
Continue.
Note: You should obtain the security PIN from your network administrator if no PIN is
displayed on the connected display device.

17
4. The HDTV displays messages to show the status of the connection.