Daintree GE current Lumination RC Series User manual

Installation Guide
IND259 | A-1028951
Lumination®LED Luminaire
RC/LRC/RX/LRX Series - New Construction Installation
BEFORE YOU BEGIN
Read these instructions completely and carefully.
WARNING / AVERTISSEMENT
RISK OF ELECTRIC SHOCK
• Turn power o before inspection, installation or removal.
• Properly ground electrical enclosure.
RISK OF FIRE
• Follow all NEC and local codes.
• Use only UL approved wire for input/output connections.
Minimum size 18 AWG (0.75mm2).
• Do not install insulation within 3 inches (76 mm) of luminaire top.
Prepare Electrical Wiring
Electrical Requirements
• The LED luminaire must be connected to the mains
supply according to its ratings on the product label.
• Class 1 wiring should be in accordance with NEC.
Grounding Instructions
• The grounding and bonding of the overall system
shall be done in accordance to local electric code of
the country where the luminire is installed.
RISQUES DE DÉCHARGES ÉLECTRIQUES
• Coupez l’alimentation avant d’inspecter, installer ou déplacer le luminaire.
• Assurez-vous de correctement mettre à la terre le boîtier d’alimentation électrique.
RISQUES D’INCENDIE
• Respectez tous les codes NEC et codes locaux.
• N’utilisez que des ls approuvés par UL pour les entrées/sorties de connexion.
Taille minimum 18 AWG (0.75mm2).
• Maintenir une distance de 76 mm (3 pouces) entre le luminaire et l’isolant.
Save These Instructions
Use only in the manner intended by the manufacturer.
If you have any questions, contact the manufacturer.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
CAN ICES-005(A)/NMB-005(A)
Note: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.

Lumination®RC/LRC/RXLRX Series Installation Guide
2
Provided Components
The components have been properly packed to avoid damage during transit. Inspect the components to conrm there is no physical
damage. Do not install damaged components.
Option A: If no holes are present on short side, use #8-1/2” self-drilling
screws
Option B: If holes are present on the short side, use the screws provided
with the frame.
Frame Installation
Cut the appropriate size
hole into the ceiling tile.
Ensure frame hole diameter
matches xture diameter.
Option A: Mount xture by attaching hanger bars to T-Grid
ceiling (BH3 SKU 94890)
Option B: Mount xture with 1.2” EMT conduit (not supplied)
Adjust xture height to be ush with ceiling and tighten both
mounting bracket wing nuts.
Place side L-brackets on existing frame
screws and tighten with screwdriver on
both sides of the frame. Then attach
mounting brackets to both L-brackets with
provided wing nuts.
Slide hanger bars
through adjustable
mounting brackets.
Fixture
Diameter
Ceiling Hole
Diameter
LRXR4 4.9-5.2in
RC6/LRC6 6.4-7.2in
RX6/
LRXR6/
LRXGR6
5.91-6.60in
RC8/LRC8 7.5-8.9in
RX8/LRXR8 7.68-8.27in
LRXR10 10.2-11.0in
LRXR12 12.2-13.0in
1
4 5
2 3

3
Open RC/LRC PSU box cover, disconnect AC conduit. Remove AC conduit wire from PSU box knockout hole using
at head screwdriver.
Insert AC line wires into the PSU box through
the knockout hole and connect wires (see
wiring diagrams to the right)
6
7
RC/LRC-Series Mounting
(RX-Series skip to step 15. LRXR and LRXG - Series, skip to step 18.
For additional information, refer to RC-series or LRC-series Installation Guides
Lumination®RC/LRC/RXLRX Series Installation Guide

4
Place PSU box onto frame next to unused
junction box and secure with U-bracket by
tightening wing nut.
Place PSU box onto frame next to unused
junction box and secure with U-bracket by
tightening wing nut.
Cut cable tie on light xture Align the xture so that two of the three springs are on each
side of the L-bracket. This is necessary in order to make
sure that when the springs release, the L-bracket does not
interfere and prevent the springs from making contact with
the top of the ceiling for proper support.
Plug together the light xture to the driver
enclosure with the supplied quick connects and
assemble the connector housing once nished.
Take the provided safety tether and loop one
end of the tether around the L-bracket.
8
10
12 13
11
9
Lumination®RC/LRC/RXLRX Series Installation Guide

5
Push xture through the hole in the ceiling. This will
engage the protruding arms, thus, releasing the springs.
The springs will draw the xture up into the ceiling and
hold it tightly in place.
Connect AC line to existing junction box. Connect conduit tting to the existing junction box. Connect the black,
white, and green/yellow wires of the input leads to the black, white and green AC line wires using UL Listed twist-
on wire connectors and close the junction box (see wiring diagram).
Connect the two quick connectors and reassemble
the connector box.
Load springs into an upright position by twisting
the springs upware. Carefully insert the xture into
the frame hole. Ensure xture is secure.
14
15
16 17
RX Series Mounting
Lumination®RC/LRC/RXLRX Series Installation Guide

6
Note:
For 1000/650lm luminaires, the default lumen output is 1000lm. Push the switch up to activate the 650lm setting.
For 4000/3000lm luminaires, the default lumen output is 4000lm. Push the switch up to activate teh 3000lm setting.
Adjusting Lumen Output
(for compatible xtures only)
LRX Series Mounting
Connect conduit end with input leads to existing
junction box and make proper connections. Connect
the black, white and green/yellow wire of the input
leads to the black, white and green wires using twist-on
wire connectors and close junction box.
Optional dimmer: When connecting a dimming
controller, wires must be run through another separate
knockout hole. Connect the violet (dimming +) and
gray (dimming - ) wires to the violet and gray wires of
the xture.
Note: Cap unused dimming leads with wire nuts
For dimming device compatibility for 0-10V and phase
cut dimming, please refer to:
www.gecurrent.com/dimming
18
19
Lumination®RC/LRC/RXLRX Series Installation Guide

7
Note:
For 2700K/3000K/3500K, default output CCT is 3000K. Push
switch UP to activate 2700K or DOWN to select 3500K.
For 3500K/4000K/5000K, default output CCT is 4000K.
Push switch UP to select 3500K and DOWN to select 5000K
Note: For 10inch and 12inch adjustable lumen xtures,
the default lumen output is set to 6000lm. Push switch
left to activate 5000lm and 4000lm respectively.
Adjusting CCT
(for compatible xtures only)
20
Lumination®RC/LRC/RXLRX Series Installation Guide
Note: The cover of the CCT switch can be used as a tool
for switching CCT settings more easily.

www.gecurrent.com
© 2020 Current Lighting Solutions, LLC. All rights reserved. GE and the GE monogram are trademarks of the
General Electric Company and are used under license. Information provided is subject to change without
notice. All values are design or typical values when measured under laboratory conditions.
IND259 (Rev 12/18/20) A-1028951
Once installed, LRX Gimbal downlight’s light
engine can be rotated up to 359° horizontally
and tilted up to 35° vertically.
Note: it is recommended to use gloves while
handling and adjusting the Gimbal light engine
to prevent dirt and oils from contaminating the
surface of the luminaire.
Load springs into an upright position by twisting
the springs upward a. Carefully insert the xture
into the hole of the rough-in frame. Verify that
the reector trim is ush to the ceiling.
23 24
Lumination®RC/LRC/RXLRX Series Installation Guide
Connect the two quick connectors and reas-
semble the connector box.
Note: Applicable only to 10in and 12 in Fixtures
Afx the hook of the safety tether onto the bracket of
the frame kit.
22
21