Adam Equipment UG119 User manual

© Adam Equipment Company 2012 700660229revA-Jul12
Adam Equipment
MUW EALT AND FITNESS SCALE
SERIE MUW 300L BÁSCULA DE SALUD Y GIMNASIA CON IMC
USER MANUAL
(P.N. 7.00. . .0229 Revision A - July 2012)

© Adam Equipment Company 2012 700660229revA-Jul12
ENGLIS : P1 - 18
ESPAÑOL: P19 - 41
EU DECLARATION: P42

EN
© Adam Equipment Company 2012 1 700660229revA-Jul12
CONTENTS
CONTENTS.........................................................................................................................1
1.0 INTRODUCTION ......................................................................................................2
2.0 SET UP.....................................................................................................................2
2.1 UNPACKING AND SETTING UP YOUR MUW.....................................................2
3.0 LOCATING AND PROTECTING YOUR SCALE ......................................................3
4.0 KEYPAD / DISPLAY FUNCTION..............................................................................4
4.1 REAR PANEL .......................................................................................................5
4.2 INTERNAL RECHARGEABLE BATTERY.............................................................5
5.0 BASIC OPERATION.................................................................................................6
5.1 SWITCHING THE BALANCE ON..........................................................................6
5.2 ZEROING..............................................................................................................6
5.3 WEIGHING UNITS................................................................................................6
5.4 HEIGHT UNITS.....................................................................................................6
5.5 WEIGHING/HEIGHT/BMI......................................................................................7
5.6 PRINTING AND OUTPUTTING THE RESULTS...................................................8
5.7 CLEARING A PREVIOUS RESULT......................................................................8
6.0 PARAMETERS.........................................................................................................9
6.1 SETTING THE BACKLIGHT OPERATION F1 EL ....................................................9
6.2 SETTING AUTO OFF F2 OFF ................................................................................10
6.3 SETTING THE PRINTING CONTROLS F3 SEr ....................................................10
6.4 PRINTING DETAIL CONTROL F4 PtSEL..............................................................11
6.5 ULTRASONIC HEIGHT CALIBRATION F5 ULtrA ................................................12
6.6 SETTING THE HOLD FUNCTION F6 HOLD..........................................................12
6.7 SETTING DATE AND TIME F7 d-t........................................................................13
6.8 SET UP F8 SET UP .................................................................................................13
6.9 TECHNICAL PARAMETERS F9 TECH ..................................................................14
7.0 USER CALIBRATION.............................................................................................15
8.0 SERIAL INTERFACE SPECIFICATIONS...............................................................16
9.0 TROUBLE SHOOTING...........................................................................................17
9.1 ERROR MESSAGES..........................................................................................17
10.0 TECHNICAL SPECIFICATIONS.............................................................................17
11.0 WARRANTY INFORMATION.................................................................................18

EN
© Adam Equipment Company 2012 2 700660229revA-Jul12
1.0 INTRODUCTION
The MUW Health and Fitness scale provides the weight and height of a patient
before calculating the BMI based on the results. Each result will be displayed on
the Indicator and held until the result is cleared, the BMI result can be used to
help evaluate some ones overall health. Units of weighing are Kg, Lbs, and Lbs
and Ounces. Height measurements are displayed in cm, feet and inches, and
inches. There is an internal rechargeable battery as well as wheels fitted to the
base that make the MUW totally portable. The results can be sent to a printer
or PC via the RS232 communication port, either manually or automatically.
2.0 SET UP
2.1 UNPACKING AND SETTING UP YOUR MUW
The MUW has been packed in such a way to make it quick and easy for the
USER to assemble, please follow the instructions as below.
1) Remove the base and pillar sections from the packaging.
2) Lift the lower pillar section and place it with the screw holes at the rear
onto the back of the base allowing for the cable to hang freely in the
open area.
3) Fit and tighten the 4 x M5 x 15 bolts and washers through the fixing plate
of the lower pillar section and into the base then slide the pillar cover
down so that it locates securely. Fix the pillar cover at the rear using 2 x
M4 x 10 screws.
4) Lift the central pillar section into position and slide it with the screw
holes at the rear onto the fixing insert ensuring the cable hangs freely
inside the pillar.
5) Fit and tighten 4 x M4 x 10 screws through the pillar and into the insert.
) Lift the top pillar section into position and slide it onto the fixing insert
with the sensor housing facing the front, again ensuring the cable hangs
freely inside the pillar.
7) Fit and tighten 4 x M4 x 10 screws through the pillar and into the insert.

EN
© Adam Equipment Company 2012 3 700660229revA-Jul12
The MUW comes with 4 x wall fixing brackets that can be secured to the
pillar before fixing to the wall. If the wall fixing brackets are being used
attach these when you fix the M4 x 10 screws to the pillar fixing inserts.
Fasten securely to the wall once you have selected the position the MUW
will be used in.
3.0 LOCATING AND PROTECTING YOUR SCALE
Avoid extremes of temperature. Do not place in
direct sunlight or near air conditioning vents.
Avoid unstable power sources. Do not use near large
users of electricity such as welding equipment or
large motors. Do not let the balance battery go flat.
If you are not using it for a long time you should
charge the battery periodically to make sure the
battery does not lose its charge.
Keep free from vibration. Do not place near heavy or
vibrating machinery.
Avoid high humidity that might cause condensation.
Keep away from direct contact with water. Do not
spray or immerse the balance in water.
Do not place near open windows, air-conditioning
vents or fans that may cause a draft and unstable
readings.
Keep the scale clean. Do not stack material on the
top pan when it is not in use.

EN
© Adam Equipment Company 2012 4 700660229revA-Jul12
4.0 KEYPAD / DISPLAY FUNCTION
The keypad and display have a number of features as shown and explained
below:
Charging LED
Battery Symbol
Zero Indicator
Stable Indicator
Tare Symbol
Ultrasonic Sensor
Symbol

EN
© Adam Equipment Company 2012 5 700660229revA-Jul12
4.1 REAR PANEL
The rear panel has a connector input for the external power adaptor (12 volts
DC @800ma).
4.2 INTERNAL RECHARGEABLE BATTERY
The scale can be operated from the internal rechargeable battery or using an
adapter. The battery life is approximately 24 hours with the backlight off.
Depending on the usage of the backlight the lifetime of the battery will reduce.
The display will show an indication when the battery needs to be charged. To
charge the battery plug the adapter into the POWER input socket in the rear
panel and connect it to the mains power supply. The charging indicator in the
lower left corner of the LCD will be on to show it is charging and will turn green
when the battery is fully charged.
KEYS PRIMARY FUNCTION SECONDARY FUNCTION
To turn the scale On or Off.
To clear the readings on the display
ready for the next weighing
To change the displayed height
reading between cm, feet or feet and
inches
To save and escape back to the
parameter settings
To send a command to print the
current displayed readings
To change the setting when in a USER
parameter
To change the displayed weight
reading between Kg, Lb’s or Lb’s and
Ounces
To change the USER parameter
To Zero the scale before weighing
To Tare any item to obtain net
weight
To enter the selected setting when in
a USER parameter

EN
© Adam Equipment Company 2012 6 700660229revA-Jul12
5.0 BASIC OPERATION
5.1 SWITCHING THE BALANCE ON
Plug in the unit using the adapter or use the internal rechargeable battery. It is
recommended that you charge the battery for at least 8 hours before first use.
1) To turn on press the [On/Off] key once and release. The scale will show
the software revision, the battery voltage, and then a self-test before
showing the stable sign and zero weight on the display.
2) The scale can now be used.
3) To turn the scale off after use press the [On/Off] key again. There is an
auto power-off function that will automatically turn the unit off if not
used for a period of time. This can be set in the parameters section .0.
5.2 ZEROING
You can press the [Zero] key to set a new zero point and show a zero reading.
This may be necessary if the weight reading is not indicating zero with nothing
on the platform, and should be done if required before each new weighing
takes place. The zero indicator will show up in the upper left corner of the LCD
when the scale displays Zero.
5.3 WEIGHING UNITS
To change the displayed weighing unit, press the [kg/lb] key which will then
cycle you through the available options of weighing units. This can only be done
before or after a weighing takes place.
5.4 HEIGHT UNITS
To change the displayed height measuring unit, press the [cm/ft] key which will
then cycle you through the available options of height measuring units. This
can only be done before or after a weighing takes place.

EN
© Adam Equipment Company 2012 7 700660229revA-Jul12
5.5 WEIGHING/HEIGHT/BMI
To determine a person’s weight, height and BMI the patient should stand on
the platform within the marked area and look straight ahead. The ultrasonic
sensor will detect that a person is on the platform signified by the symbol in
the upper right part of the display and start to determine the height. When a
stable reading of weight is obtained the three readings will be displayed.
The results will remain on the display until the [Clear] key is pressed.
Results from a BMI measurement can be determined as the table below.
BMI Weight Status
Below 18.5 Underweight
18.5 – 24.9 Normal
25.0 – 29.9 Overweight
30.0 and Above Obese

EN
© Adam Equipment Company 2012 8 700660229revA-Jul12
5.6 PRINTING AND OUTPUTTING THE RESULTS
If a printer or other data collection device is being used the results will be sent
automatically or manually depending on the printing control set up. The data
transmission speed must be set correctly to allow the results to be received.
The Doctor and patients identity number can be programmed into the Indicator
to give you a traceable record which also records date and time.
To enter the Doctors Id press and hold the [Print] key for 2 seconds. The
display will show as below, use the [Print] and [Clear] keys to move the flashing
digit and the [kg/lb] and [cm/ft] keys to enter the Id number you require and
press [Zero] to save.
The display will now show the Patients Id screen, use the keys as above to set
the Id number and press [Zero] to save and exit back to normal weighing.
See section .3 and .4 for printing controls and data transmission speed
options
5.7 CLEARING A PRE IOUS RESULT
Once the results have been calculated and displayed they will remain displayed
until the [Clear] key is pressed. When the patient has stepped off the platform
and the results have been recorded or printed, the [Clear] key can then be
pressed which will return the display to zero ready for the next patient to be
weighed.

EN
© Adam Equipment Company 2012 9 700660229revA-Jul12
6.0 PARAMETERS
The balance has 8 parameters where options can be set by the user.
FUNCTION SECTION DESCRIPTION
F1
F1F1
F1 EL
ELEL
EL See section .1 Sets the backlight operation
Default is AUTO
F2
F2F2
F2 OFF
OFFOFF
OFF
See section .2 Auto off function
Default is 10
F
FF
F3
33
3 SE
SESE
SE R
RR
R See section .3 Sets the printing control and data transmission speed
Default is 9 00
F
FF
F4
44
4 P
PP
P T
T T
T S
SS
SEL
ELEL
EL See section .4 Printing controls
F
FF
F5
55
5 UL
ULUL
UL TR
TRTR
TR A
AA
A See section .5 Calibration of the height sensor
F6
F6F6
F6 HOLD
HOLDHOLD
HOLD See section . Sets the HOLD function to ON or OFF
F7
F7F7
F7 D
DD
D -
--
- T
TT
T
See section .7 Setting the date and time
F8
F8F8
F8 SET
SETSET
SET UP
UPUP
UP
See section .8 Set up parameters
F9
F9F9
F9 TECH
TECHTECH
TECH Service only
6.1 SETTING THE BACKLIGHT OPERATION F1
F1F1
F1 EL
ELEL
EL
The backlight function can be set by the user.
AUTO Sets the backlight to operate automatically when a weight is
placed on the platform or a key is pressed.
OFF Sets the backlight to be on at all times.
ON Sets the backlight to be off at all times.
1) Switch on the scale then press the [kg/lb] key during the self-checking
test of the display.
2) The display will show the first function F1
F1F1
F1 EL
ELEL
EL.
..
.
3) Press the [Zero] key to select F1
F1F1
F1 EL
ELEL
EL and show the current setting, default
is AUTO.
4) Press the [Print] key to change the setting for the backlight and press
[Zero] to save, then [kg/lb] to select the next parameter.

EN
© Adam Equipment Company 2012 10 700660229revA-Jul12
6.2 SETTING AUTO OFF F2
F2F2
F2 OFF
OFFOFF
OFF
An automatic power down time can be set so that the MUW turns off after a
period where no activity is detected. This preserves the life time of the battery
when used in this mode.
Settings are OFF, 5, 10, 20, and 30 minutes.
1) Switch on the scale then press the [kg/lb] key during the self-checking
test of the display.
2) The display will show the first function
F1
F1F1
F1 EL.
EL.EL.
EL.
3) Press the [kg/lb] key to select F2
F2F2
F2 OFF
OFFOFF
OFF and then [Zero] to enter and show
the current setting, default is 10.
4) Press the [Print] key to change the setting for the backlight and press
[Zero] to save, then [kg/lb] to select the next parameter.
6.3 SETTING THE PRINTING CONTROLS F
FF
F3
33
3 SE
SESE
SE R
RR
R
The MUW can be set to automatically print “AUTO”, or print on demand “PrN”
by pressing the [Print] button.
The data transmission speed “Bps” of the MUW must match that of the Printer
or other device being used to collect data information successfully.
The printing control and speed can be selected as follows.
1) Switch on the scale then press the [kg/lb] key during the self-checking
test of the display.
2) The display will show the first function
F1
F1F1
F1 EL.
EL.EL.
EL.
3) Press the [kg/lb] key to select F
FF
F3
33
3 S
SS
S ER
ERER
ER and then [Zero] to enter and show
the current printing control setting “UArt”.
4) Either printing on demand (PrN), pressing the [Print] key following a
weighing, or printing automatically (AUTO), automatically prints out
when a stable reading and BMI calculation is displayed can be selected.

EN
© Adam Equipment Company 2012 11 700660229revA-Jul12
5) Press the [Print] key to change the setting for the printing control and
press [Zero] to save.
) The current setting for data transmission speed “Bps” will now be
displayed.
00, 1200, 2400, 4800, 9 00 are available. Default is 9 00.
Press the [Print] key to change the setting and press [Zero] to save.
Test will be displayed, press the [Print] key to send a test print
command.
7) Press [Zero] to save, [cm/ft] to exit, then [kg/lb] to select the next
parameter.
6.4 PRINTING DETAIL CONTROL
F
FF
F4
44
4 P
PP
P T
TT
T S
SS
SE
EE
EL
LL
L
The MUW can be programmed to provide a customised print out to give you
the readings you require. Doctor, patient, DiSP1, DiSP2, DiSP3 details can all be
enabled or disabled to suit the information you need to see.
1) Switch on the scale then press the [kg/lb] key during the self-checking
test of the display.
2) The display will show the first function
F1
F1F1
F1 EL.
EL.EL.
EL.
3) Press the [kg/lb] key to select F4
F4F4
F4 P
PP
P T
TT
T S
SS
SE
EE
EL
LL
L and then [Zero] to enter and
show the current settings.
SETTING DESCRIPTION SELECTIONS
dr.Id Doctors Id number ON/OFF
PAt.Id Patient Id number ON/OFF
DiSP 1 Display 1 shows the weight of the patient ON/OFF
DiSP 2 Display 2 shows the height of the patient ON/OFF
DiSP 3 Display 3 shows the BMI of the patient ON/OFF
CAL Print out following calibration ON/OFF
d-t Date and time ON/OFF

EN
© Adam Equipment Company 2012 12 700660229revA-Jul12
4) Press the [Print] key to change the setting for the printing detail control
and press [Zero] to save.
5) Press the [kg/lb] key to exit and continue.
6.5 ULTRASONIC HEIGHT CALIBRATION F
FF
F5
55
5 UL
ULUL
UL TR
TRTR
TR A
AA
A
The Ultrasonic height sensor has been factory calibrated and should not require
frequent calibration. If there is a problem with height measuring proceed as
below.
1) Switch on the scale then press the [kg/lb] key during the self-checking
test of the display.
2) The display will show the first function
F1
F1F1
F1 EL.
EL.EL.
EL.
3) Press the [kg/lb] key to select F
FF
F5
55
5 U
UU
U LTRA
LTRALTRA
LTRA and then [Zero] to enter the
sensor calibration section “AdJUST” XX (XX being a factory set figure)
4) Press the [Zero] key and the display will show “base- H 220”, press [Zero]
to calibrate the “Zero” height reading.
5) The display will show “test” and a 4 digit number. Press the [Zero] key
from a position where the height sensor cannot detect you.
) When calibration is complete the display will show “AdJUST XX”.
If after calibration the height sensor is not measuring correctly, press [Print] or
[Clear] at point 3 to change XX. A lower number will decrease the height
measurement and a higher number will increase it. Then continue from point 4
on.
*A print out with date and time can be issued following every calibration.
6.6 SETTING THE HOLD FUNCTION
F6
F6F6
F6 HOLD
HOLDHOLD
HOLD
The Hold function can be set so that the height and BMI readings are visible as
they are being calculated (OFF), or remain as dashes until the weight reading is
stable upon where they will be displayed (ON).
1) Switch on the scale then press the [kg/lb] key during the self-checking
test of the display.

EN
© Adam Equipment Company 2012 13 700660229revA-Jul12
2) The display will show the first function F1
F1F1
F1 EL.
EL.EL.
EL.
3) Press the [kg/lb] key to select F
FF
F6
66
6 HOLD
HOLDHOLD
HOLD and then [Zero] to enter and
show the current setting, default is ON.
4) Press the [Print] key to change the setting for Hold, press [Zero] to save,
then [kg/lb] to select the next parameter.
6.7 SETTING DATE AND TIME
F7
F7F7
F7 D
DD
D -
--
- T
TT
T
1) Switch on the scale then press the [kg/lb] key during the self-checking
test of the display.
2) The display will show the first function F1
F1F1
F1 EL
ELEL
EL ..
3) Press the [kg/lb] key to select F7
F7F7
F7 D
DD
D -
--
- T
TT
T and then [Zero] to enter the date
setting display.
4) The display will show the day, month and year.
5) To change any setting press the [kg/lb] key to increment the flashing
digit and either the [Print] or [Clear] key to move the flashing digit to the
left or right.
) Press the [Zero] key to save the date and enter the time setting
parameter
7) To change the time press the [kg/lb] key to increment the flashing digit
and either the [Print] or [Clear] key to move the flashing digit to the left
or right.
8) Press [Zero] to save, [cm/ft] to exit then [kg/lb] to select the next
parameter.
6.8 SET UP
F8
F8F8
F8 SET
SETSET
SET UP
UPUP
UP
Four performance parameters, Filter, Auto Zero, Stability and weight tracking
are available to the USER.
These parameters influence the speed of the display update and have been
factory set, the default settings should normally be used to optimise
performance.

EN
© Adam Equipment Company 2012 14 700660229revA-Jul12
Available parameters and settings are as below.
PARAMETER
DESCRIPTION DEFAULT VALUE
FILT Filter settings of 1- are available
1 is the fastest filter, 3 is the slowest.
ERO Automatic Re-zero range
Settings of 1 to are available 2
STA
Stability symbol range
Settings of 1 to are available
1 is the smallest stability range and is the largest.
TR Weight Tracking Range
Settings of 1 to are available 4
1) Switch on the scale then press the [kg/lb] key during the self-checking
test of the display.
2) The display will show the first function F1
F1F1
F1 EL.
EL.EL.
EL.
3) Press the [kg/lb] key to select F
FF
F8
88
8 SET
SETSET
SET UP
UPUP
UP and then [Zero] to enter and
show the first parameter.
4) Press the [Print] key to change the setting and [Zero] to save and move
to the next parameter, press [cm/ft] to exit.
To return to normal operation turn the scale OFF and then ON again.
6.9 TECHNICAL PARAMETERS
F9
F9F9
F9 TECH
TECHTECH
TECH
This is a menu available only to qualified service personnel for factory
adjustments.

EN
© Adam Equipment Company 2012 15 700660229revA-Jul12
7.0 USER CALIBRATION
1) Switch on the scale and whilst the display counts down press the [Clear]
key.
2) The display will show kg or lb, press [Print] to select the unit of weight
being used for the calibration and then [Zero] to confirm.
3) The display will show CAL XX (XX being the last calibration weight to be
used).
4) Press the [Print] key to change the value if required and [Zero] to
confirm.
5) The display will show the Zero A-D which should be stable.
) Press the [Zero] key to confirm the Zero point and the display will show
LOd XX (XX being the calibration weight value to be loaded onto the top
pan).
7) Load the top pan with the calibration weight and press the [Zero] key.
8) The display will show “PASS” for a successful calibration and return to
normal weighing displaying the calibration weight value correctly.
9) Remove the weight from the pan and the scale will return to Zero.
*A print out with date and time can be issued following every calibration.
If an error code was displayed when calibrating please see the error code
table in section 9.1

EN
© Adam Equipment Company 2012 16 700660229revA-Jul12
8.0 SERIAL INTERFACE SPECIFICATIONS
The balance comes equipped with an RS-232 Serial Interface.
The connector is a DE-9P female fitting with the following connections.
Pin 2 TXD Transmitted data
Pin 3 RXD Received data
Pin 5 GND Signal ground
Printing Output:
The lines will include a heading for each detail then the value. A typical output
when weighing is shown below. lines of data are printed if all are enabled.
All lines end with a carriage return <cr> and a line feed <lf>, (0dH and 0aH in
ASCII).
Input command format:
The balance can be controlled by a PC with the following commands. The
commands must be sent in upper case letters, i.e. “T” not “t”.
Z<cr><lf> Will Zero the scale, performs the same functions as pressing the [Zero] key.
P<cr><lf> Will send a Print command to a PC or Printer. Performs the same functions as
pressing the [Print] key.
C<cr><lf> Will clear the last recorded reading from the display. Performs the same
functions as pressing the [Clear] key
W<cr><lf> Will change the Weight measuring unit being used between kg, lbs and lbs
and ounces. Performs the same functions as pressing the [kg/lb] key.
H<cr><lf> Will change the Height measuring unit being used between cm, inches and
feet and inches. Performs the same functions as pressing the [cm/ft] key.
Doctor Id: 00001
Patient Id: 0000000123
Weight: 80.00 kg
Height: 183 cm
BMI: 23.9
D&T
30/07/2012 11.20

EN
© Adam Equipment Company 2012 17 700660229revA-Jul12
9.0 TROUBLE S OOTING
9.1 ERROR MESSAGES
If an error message is shown, repeat the step that caused the message. If the
error message is still shown then contact your dealer for support.
DISPLAYED MESSAGE DESCRIPTION
Err Measured height is above
210cm/82.5 inches
UNDER Measured height is below
80cm/31.5 inches
Err H Calibration weight value
used too high
Err L Calibration weight value
used too low
- - - - - - Weight on top pan exceeds
300kg/ 0Lbs
10.0 TEC NICAL SPECIFICATIONS
Model MUW 300L
Maximum Capacity 300kg/ 0Lbs
Readability 0.05kg/0.1Lbs
Repeatability (s.d.) 0.1kg/0.2Lbs
Linearity ± 0.1kg/0.2Lbs
Units of Height Cm, inches, feet and inches
Height range 80cm – 210cm/ 31.5 - 82.5 inches
Units of Weight Kg, lb’s, lb’s and ounces
Power Supply 12vDC 500mA or 800ma, or
Internal rechargeable vDC battery
Overall Dimensions
w x d x h
0.38m x 0. m x 2.3m
15 x 23. x 90.2 inches

EN
© Adam Equipment Company 2012 18 700660229revA-Jul12
11.0 WARRANTY INFORMATION
Adam Equipment offers Limited Warranty (Parts and Labour) for any components that fail due to defects in
materials or workmanship. Warranty starts from the date of delivery.
During the warranty period, should any repairs be necessary, the purchaser must inform its supplier or
Adam Equipment Company. The company or its authorised Technician reserves the right to repair or
replace the components at any of its workshops at no additional cost, depending on the severity of the
problems. However, any freight involved in sending the faulty units or parts to the Service Centre should be
borne by the purchaser.
The warranty will cease to operate if the equipment is not returned in the original packaging and with
correct documentation for a claim to be processed. All claims are at the sole discretion of Adam
Equipment.
This warranty does not cover equipment where defects or poor performance is due to misuse, accidental
damage, exposure to radioactive or corrosive materials, negligence, faulty installation, unauthorised
modifications or attempted repair, or failure to observe the requirements and recommendations as given in
this User Manual.
This product may include a rechargeable battery that is designed to be removed and replaced by the user.
Adam Equipment warrants that it will provide a replacement battery if the battery manifests a defect in
materials or workmanship during the initial period of use of the product in which the battery is installed.
As with all batteries, the maximum capacity of any battery included in the product will decrease with time
or use, and battery cycle life will vary depending on product model, configuration, features, use, and power
management settings. A decrease in maximum battery capacity or battery cycle life is not a defect in
materials or workmanship, and is not covered by this Limited Warranty.
Repairs carried out under the warranty do not extend the warranty period. Components removed during
warranty repairs become company property.
The statutory rights of the purchaser are not affected by this warranty. The terms of this warranty is
governed by the UK law. For complete details on Warranty Information, see the terms and conditions of
sale available on our web-site.