Adam Equipment Warrior Series User manual

(P.N. 3136611622 - Revision D, Apr 2014) © Adam Equipment Company 2014
Adam Equipment
WARRIOR SERIES
USER MANUAL
SW Ver. 1.24
Adam Equipment strives to be more environmentally focused and uses recycled materials and
environmentally friendly packaging where possible. As part of this initiative we have developed a short
manual that uses less paper and ink to describe the main functions of your new Adam product. A complete
version is available at www.adamequipment.com. Thank you for your support of Adam Equipment.

(P.N. 3136611622 - Revision D, Apr 2014) © Adam Equipment Company 2014
ENGLISH: P 1 - 18
FRANÇAIS: P 19 - 37
DEUTSCH: P 38 - 55
ESPAÑOL: P 56 - 75
ITALIANO: P 76 - 94
EU DECLARATION: P 95

EN
© Adam Equipment Company 2014 1 (P.N. 3136611622 - Revision D, Apr 2014)
CONTENTS
1.0 INTRODUCTION.................................................................................................................................. 2
2.0 SPECIFICATIONS................................................................................................................................ 3
3.0 INSTALLATION.................................................................................................................................... 4
3.1 UNPACKING.................................................................................................................................... 4
3.2 LOCATING....................................................................................................................................... 4
3.3 SETTING UP THE SCALES ............................................................................................................ 5
4.0 KEY DESCRIPTIONS........................................................................................................................... 6
5.0 DISPLAYS ............................................................................................................................................ 7
6.0 OPERATION......................................................................................................................................... 8
6.1 ZEROING THE DISPLAY................................................................................................................. 8
6.2 TARING............................................................................................................................................ 8
6.3 WEIGHING A SAMPLE.................................................................................................................... 9
6.4 PARTS COUNTING....................................................................................................................... 10
6.5 CHECK-WEIGHING....................................................................................................................... 10
6.6 ACCUMULATED TOTAL ............................................................................................................... 11
6.7 PERCENTAGE WEIGHING........................................................................................................... 11
6.8 ANIMAL (Dynamic) WEIGHING..................................................................................................... 11
7.0 USER PARAMETERS........................................................................................................................ 11
8.0 BATTERY OPERATION..................................................................................................................... 12
9.0 RS-232 INTERFACE.......................................................................................................................... 12
9.1 INPUT COMMANDS FORMAT...................................................................................................... 13
10.0 RELAY INTERFACE........................................................................................................................... 13
11.0 CALIBRATION.................................................................................................................................... 14
12.0 SERVICE PARAMETERS.................................................................................................................. 15
12.1 USING THE SERVICE PARAMETERS......................................................................................... 15
13.0 ERROR CODES................................................................................................................................. 16
WARRANTY INFORMATION ........................................................................................................................ 16

EN
© Adam Equipment Company 2014 2 (P.N. 3136611622 - Revision D, Apr 2014)
1.0 INTRODUCTION
•The WARRIOR series provide accurate, fast and versatile general
purpose type weighing scales with parts counting, percentage
weighing and check-weighing functions.
•The WARRIOR has LED’s next to the display to indicate when a
weight is below the low limit, in between the limits or above the
high limit. These can work in conjunction with an audible alarm for
check weighing as well as the display showing LO, OK and HI.
•The WARRIOR is supplied with a RS-232 bi-directional interface
and real time clock (RTC).
•The WARRIOR has a sealed keypad with colour coded
membrane switches, a large easy to read liquid crystal display
(LCD) and a green backlight.
•Included functions are automatic zero tracking, semi-automatic
tare and an accumulation facility that allows the weight to be
stored and recalled as an accumulated total.

EN
© Adam Equipment Company 2014 3 (P.N. 3136611622 - Revision D, Apr 2014)
2.0 SPECI ICATIONS
Model #
WSK 8
WSK 16a
WSK 16
WSK 35a
WSK 32
WSK 70a
WBK 32
WBK 70a
WBK 32H
WBK70aH
WBK 75
WBK 165a
Maximum
Capacity 8000g/16lb 16kg/35lb 32kg/70lb 32kg/70lb 32kg/70lb 75kg/165lb
Readability 0.5g/0.001lb 0.001kg/
0.002lb 0.002kg/ 0.005lb 0.002kg/ 0.005lb 0.001kg/ 0.002lb 0.005kg/ 0.01lb
Resolution 1:16000 1:16000 1:16000 1:16000 1:32000 1:15000
Repeatability
(Std. Dev) 1g/0.002lb 0.002kg/ 0.004lb 0.004kg/ 0.01lb 0.004kg/ 0.01lb 0.002kg/ 0.004lb 0.01kg/ 0.02lb
Linearity + 1g/0.002lb 0.002kg/
0.004lb 0.004kg/ 0.01lb 0.004kg/ 0.01lb 0.002kg/ 0.004lb 0.01kg/ 0.02lb
Pan size
w x d 250mm x 250mm/ 9.8in x 9.8in 300mm x 400mm/ 11.8in x 15.7in
Units of
Measure g / Kg / Lb / Lb:oz / Newtons / Ounces
Model #
WFK 75
WFK 165a
WFK 75H
WFK 165aH
WFK 15
0
WFK 330a
WLK 150
WLK 330a
Maximum
Capacity 75kg/165lb 75kg/165lb 150kg/330lb 150kg/330lb
Readability 0.005kg/0.01lb 0.001kg/0.002lb 0.01kg/0.02lb 0.01kg/0.02lb
Resolution 1:15000 1:75000 1:15000 1:15000
Repeatability
(Std. Dev) 0.01kg/0.02lb 0.002kg/0.004b 0.02kg/0.04lb 0.02kg/0.04lb
Linearity + 0.01kg/0.02lb 0.002kg/0.004lb 0.02kg/0.04lb 0.02kg/0.04lb
Pan size
w x d 400mm x 500mm/ 15.7in x 19.7in 450mm x
600mm/ 17.7in x
23.6in
Units of
Measure g / Kg / Lb / Lb:oz / Newtons/Ounces
COMMON SPECIFICATIONS FOR ALL MODELS
Stabilization Time 2-3 Secs
Operating Temperature -10°C to +40°C / +32°F to +104°F
Power Supply + 6v 4.5Ah battery
12vDC 800mA External adaptor
Calibration External
Calibration Mass User Selectable
Display Backlit Green display 40mm high digits with capacity tracker
Balance Housing 304 Stainless steel housing, IP66 rated

EN
© Adam Equipment Company 2014 4 (P.N. 3136611622 - Revision D, Apr 2014)
3.0 INSTALLATION
3.1 UNPACKING
The WARRIOR scales have already been adjusted to work with a platform
and have been configured for this application. The platform and indicator
have been calibrated as a pair and must be used together.
3.2 LOCATING
•
The scales should not be placed in a location that
will reduce the accuracy.
•Avoid extremes of temperature. Do not place in
direct sunlight or near air conditioning vents.
•Avoid unsuitable tables. The table or floor must be
rigid and not vibrate.
•Avoid unstable power sources. Do not use near
large users of electricity such as welding equipment
or large motors.
•Do not place near vibrating machinery.
•Avoid high humidity that might cause condensation.
Avoid direct contact with water. Do not spray or
immerse the scales in water.
•Avoid air movement such as from fans or opening
doors. Do not place near open windows or air-
conditioning vents.
•Keep the scales clean. Do not stack material on the
scales when they are not in use.

EN
© Adam Equipment Company 2014 5 (P.N. 3136611622 - Revision D, Apr 2014)
3.3 SETTING UP THE SCALES
•Remove the Indicator from its box and fix it to the U shaped
bracket using the 2 x fixing handles. Take the Indicator and place
it onto the pillar ensuring the slack cable is pushed inside. Fix the
Indicator to the pillar using the screw provided.
•Remove all upper internal packaging, place the pillar into the base
bracket fitting and remove the complete machine from the box.
Remove any plastic bags that may have been used for protection.
•Fix the pillar to the base bracket fitting using the screws provided
•Adjust the viewing angle of the Indicator to the ideal position and
tighten the 2 x locking handles.
•Level the scale by adjusting the five feet on the WSK/WBK or the
four feet on the WFK/WLK. If the scale rocks re-adjust the feet.
NOTE: Use of a food-safe grease is recommended on the threaded part
of the feet to keep them turning freely.
•Attach the power to the indicator and press the [On/Off] key. The
software revision number will be displayed followed by a self-test
showing all digits before the zero is displayed along with the unit
of weight that was last used.
•Optional connections to RS232 port and relay wiring port should
be made if required.

EN
© Adam Equipment Company 2014 6 (P.N. 3136611622 - Revision D, Apr 2014)
4.0 KEY DESCRIPTIONS
Used to reset the display to zero.
Tares the scale. Used to deduct and store the weight
currently on the scale if it is not required as part of the
final weighing result.
A secondary function, is of an “Enter” key used
when setting up a value for the Parameters.
Selects parts counting. Used to set the sample
quantities while parts counting.
A secondary function is of incrementing the active
digit when setting a value for Parameters.
Selects the weighing unit to be displayed from those
which are enabled. See parameter S1 in the full
manual.
A secondary function is to move the active/flashing
digit to the left when setting values for Parameters.

EN
© Adam Equipment Company 2014 7 (P.N. 3136611622 - Revision D, Apr 2014)
Selects the Function parameters of the scale.
A secondary function (C) is to act as a clear key when
clearing an accumulated total.
Sends the results to a PC or a Printer using the RS-
232 interface. It also adds the value to the
accumulation memory if the accumulation function is
not automatic.
A secondary function (ESC) is to return to normal
operation when the scale is in a Parameter setting
mode.
To switch the Indicator on or off.
The WARRIOR will store the weighing unit and the
check weighing values currently in use if power is
powered off. These will be re called when the Indicator
is next powered on
5.0 DISPLAYS
The LCD display will show a value as well as the unit currently being used. In
addition the LED’s above the display will show when a weight is below, inside
or above the check-weighing limits.
Other symbols will show when a weight has been tared (NET), the scale is at
zero and stable, if a value has been stored in memory, or when the animal
weighing function has been enabled. A battery symbol will show the state of
charge of the internal battery.

EN
© Adam Equipment Company 2014 8 (P.N. 3136611622 - Revision D, Apr 2014)
6.0 OPERATION
6.1 ZEROING THE DISPLAY
•You can press the [0/T] key at any time to set the display to zero.
This will usually be when the platform is empty. When the zero
point is obtained the display will show an indicator for zero.
•The scale has an automatic re-zeroing function to account for
minor drifting or accumulation of material on the platform.
However you may need to press the [0/T] key to re zero the scale
if small amounts of weight are shown when the platform is empty.
6.2 TARING
•Zero the scale by pressing the [0/T] key if necessary. The
“ZERO” indicator will be ON.
•Place a container on the platform and a value for its weight will be
displayed.

EN
© Adam Equipment Company 2014 9 (P.N. 3136611622 - Revision D, Apr 2014)
•Press the [0/T] key to tare the scale. The weight is deducted and
stored as the tare value leaving zero on the display. The “NET”
indicator will be ON and as a product is added only the net weight
of the product will be shown. The scale could be tared a second
time if another type of product was to be added to the first one.
Again only the weight that is added after taring will be displayed.
NOTE: The “NET” indicator will only be ON when the tare weight
exceeds 4% (+/- 2weighing divisions) of the scale capacity.
•When the container is removed a negative value will be shown. If
the scale was tared just before removing the container this value
is the gross weight which includes the container and the entire
product it contains. The “ZERO” indicator will be on to indicate
that the platform is back to the same condition as it was when
zero was last set.
•To delete a Tare value, press [0/T] when the pan is empty.
6.3 WEIGHING A SAMPLE
To determine the weight of a sample, first tare the empty container if it is to
be used and then place the sample in the container. The display will show the
net weight of the sample and the unit of weight currently in use.

EN
© Adam Equipment Company 2014 1 0 (P.N. 3136611622 - Revision D, Apr 2014)
6.4 PARTS COUNTING
If parts counting is enabled (see section full user manual), it is possible to
count parts using a sample of the parts to determine an average piece
weight.
•If using an empty container, place the container on the top pan
and press [0/T] to zero the display. Press the [PCS] key to enter
parts counting mode.
•The scale will show “P 10”. Change the sample size to the desired
quantity by pressing the [PCS/]key. It will cycle through the
options: 10, 20, 50, 100, 200 and back to 10.
•Place the nominated sample size into the container and press
[0/T]. The sample number should match the sample amount
options available for parts counting, i.e., 10, 20, 50, 100 or 200
pieces.
•The display will now show the amount of parts in the container,
and as more parts are added the display will increase to show the
number of parts in the container at that time. (PCS).
Pressing the [Unit/]key will display the net weight (PCS and kg), pressing
it a second time will display the unit weight (g/pcs), and the third time will
display the count again (PCS).
•Press the [PCS/]key to return to normal weighing. Press the
[PCS/]key again to start counting a different sample.
6.5 CHECK-WEIGHING
Check-weighing is a procedure where the LED’s come on (and if enabled, an
alarm to sound) when the weight on the scale meets values stored in
memory. The memory holds the last values for a high and a low limit when
the power is turned off. The user can set either one limit or both, see the full
version of the user manual for details of the check weighing function.

EN
© Adam Equipment Company 2014 1 1 (P.N. 3136611622 - Revision D, Apr 2014)
6.6 ACCUMULATED TOTAL
The scale can be set to accumulate manually by pressing the [Print/M+/Esc]
key, or automatically when a weight is removed from the scale. See full
version of the user manual for complete details.
6.7 PERCENTAGE WEIGHING
The scale can be set to perform percentage weighing. See full version of the
user manual for complete details.
6.8 ANIMAL (DYNAMIC) WEIGHING
The scale can be set to animal (dynamic) weighing for weighing any items
that are unstable or may move. See full version of the user manual for
complete details.
7.0 USER PARAMETERS
Pressing the [Func/C] key during normal operation allows the user to access
the parameters for customizing the scale. The parameters are split into 4
groups-
1. Check weighing parameters,
2. Percentage and Animal Weighing Functions
3. RS-232 parameters
4. Scale parameters
•When [Func/C] is pressed the display will first show “FunC 1” for
Check weighing parameters.
•Press either the [Func/C] key or the [Pcs/

] to advance through
the groups “FunC 1”, “FunC 2” , “FunC 3” and “FunC 4”. When the required
function is displayed, press [

0/T

] to enter the sub-menu for
setting desired parameters for this function.
•When in one of the sections press [Print/M+/Esc] to regress one
step each time. If you press [Print/M+/Esc] repeatedly, you will exit
the User Parameter section and return to normal weighing.
Complete details of all parameters can be found in of the full version of the
user manual.

EN
© Adam Equipment Company 2014 1 2 (P.N. 3136611622 - Revision D, Apr 2014)
8.0 BATTERY OPERATION
•The scales can be operated from the battery if desired. The
battery life can be up to 70 hours depending on the load cells and
how the backlight is used.
•A battery symbol is shown on the display which indicates the
current charge of the battery, 3 bars means fully charged. When
just the outline of the battery and no bars are visible the battery
needs to be re charged.
•To charge the battery, simply plug the adaptor into the mains
power, and also into the input connector on the rear of the
Indicator marked DC 12V. The scale does not need to be turned
on.
•The battery should be charged for 12 hours to reach full capacity.
•Near the display is an LED to indicate the status of battery
charging. When the scale is plugged into the mains power the
internal battery will be charged. If the LED is green the battery has
a full charge. If it is red the battery is nearly discharged and yellow
indicates the battery is being charged.
9.0 RS-232 INTER ACE
The Warrior indicator is supplied with bi-directional RS-232 interface as
standard. The scale, when connected to a printer or computer outputs the
weight with the selected weighing unit through the RS-232 interface.
Specifications:
RS-232 output of weighing data
ASCII code
600 - 19200 Baud (user selectable, default 9600)
8 data bits, No Parity, 1 stop bit, no flow control

EN
© Adam Equipment Company 2014 1 3 (P.N. 3136611622 - Revision D, Apr 2014)
The RS-232 serial interface is located inside the housing, access is gained by
removing the 8 x case screws whereby connections can be made to COM 1
as shown below.
RXT Received Data
TXT Transmitted Data
GND Signal Ground
The cable used should be routed through the gland marked RS 232 on the
case and tightened securely to ensure a watertight connection is made.
The scale can be set to print text in English, French, German or Spanish.
See the RS-232 parameters section for details
9.1 INPUT COMMANDS FORMAT
The scale can be controlled with the following commands. Press the [Enter]
key of the PC after each command.
T<cr><lf>
Tares the scale to display the net weight. This is the same as pressing [0/T].
Z<cr><lf> Sets the zero point for all subsequent weighing. The display
shows zero.
P<cr><lf> Prints the results to a PC or printer using the RS-232
interface. It also adds the value to the accumulation memory
if the accumulation function is not set to automatic.
10.0 RELAY INTER ACE
The indicator is supplied with drivers to control external relays. The drivers
could be used to control a number of different relays depending upon the
users needs. The relay drivers are isolated outputs requiring the use of an
external power supply and the relay option kit.
See of the full version of the user manual for complete details.

EN
© Adam Equipment Company 2014 1 4 (P.N. 3136611622 - Revision D, Apr 2014)
11.0 CALIBRATION
The scale can be calibrated using the following procedure. To enter this
procedure it is necessary to use Func 4 which is accessible using the
[Func/C] key as described in section 7.4 in the full manual, or by using the
passcode access as described in section 12.0.
The scales calibrate using either metric or pound weights depending on the
weighing unit being used before calibration. The display will show either "kg"
or "lb" to identify the weights expected.
PROCEDURE
•Enter the calibration section using Func 4, C8 CAL or using the
passcode as described in section 12.0.
•The display will show "unLoAd".
•Remove any weight from platform and when the stable symbol is
on press [0/T].
•The display will show "Ld" then “0000XX” which shows the last
calibration weight used. Place this calibration weight on the scale
and press the [0/T] key. If the weight you put on the scale does
not match the value displayed, press the [Func/C] key to clear the
vale then use the [Unit/]key and [PCS/]key to set the correct
value. When it is correct press [0/T].
•If the calibration is acceptable the scale will run a self-test during
which the calibration weight should be removed. If an error
message “FAiL L” is shown try calibration again as a disturbance
may have prevented a successful calibration.
After calibration the scale should be checked to verify the calibration is
correct. If necessary repeat the calibration making sure that the scale is
stable before accepting any weight.

EN
© Adam Equipment Company 2014 1 5 (P.N. 3136611622 - Revision D, Apr 2014)
12.0 SERVICE PARAMETERS
The scales will allow entry to the parameters if the [Tare] key is pressed
during the power on cycle. The passcodes work as explained earlier.
In this case the display will show the passcode request screen, “ P - - - - “ . To
continue enter a passcode as described below.
Entering passcode 0000 will allow calibration as shown in section 11.
Entering 1000 will allow access to a limited set of parameters described in
section 12.1.
12.1 USING THE SERVICE PARAMETERS
Press the [0/T] key during the display countdown when turning on,
When “Pn“ is displayed, enter the number 1000 using the [Unit/]and
[PCS/]keys and then press [0/T].
The display will show the first parameter called “F4 Int”.
To select another parameter press the [PCS/]key which will advance
through the parameters available. Full details are in the full version of the
user manual.

EN
© Adam Equipment Company 2014 1 6 (P.N. 3136611622 - Revision D, Apr 2014)
13.0 ERROR CODES
ERROR
CODES DESCRIPTION SUGGESTIONS
- -oL - - Over-range Remove weight from the scale.
If the problem persists contact your dealer or Adam
Equipment for assistance.
Err 1 Time Setting
Error Enter time using correct format and reasonable values. Format: hh:mm:ss
Err 2 Date Setting
Error Enter date using correct format and reasonable values. Format: yy:mm:dd
Err 4 Zero Setting
Error The scale was outside the normal zero setting range either when it was turned on, or when the
[Zero] key was pressed.
Remove weight from the scale and try re-zeroing
again.
Use the [0/T] key to set the display to zero value.
If the problem persists contact your dealer or Adam
Equipment for assistance.
Err 6 A/D out of range
The values from the A/D converter are outside the
normal range.
Remove the weight from the scale if overloaded.
Make sure the pan is fitted correctly.
Indicates the load cell or the electronics may be
faulty.
If the problem persists contact your dealer or Adam
Equipment for assistance.
Err 7
100% weight out
of range Weight value set as 100% for percentage weighing must be greater than 50 weighing divisions of the
scale.
Err 9 Check weigh
limits error Shown if the low limit is set higher than the current high limit. Reset High limit or change the low limit.
FAIL Calibration
error. Improper calibration (should be within + 10% of the factory calibration). The old calibration data will be
retained until the calibration process is complete.
If the problem persists contact your dealer or Adam
Equipment for assistance.

EN
© Adam Equipment Company 2014 1 7 (P.N. 3136611622 - Revision D, Apr 2014)
WARRANTY STATEMENT
Adam Equipment offers Limited Warranty (Parts and Labour) for any components that fail due to defects in
materials or workmanship. Warranty starts from the date of delivery.
During the warranty period, should any repairs be necessary, the purchaser must inform its supplier or Adam
Equipment Company. The company or its authorised Technician reserves the right to repair or replace the
components at any of its workshops at no additional cost, depending on the severity of the problems. However,
any freight involved in sending the faulty units or parts to the Service Centre should be borne by the purchaser.
The warranty will cease to operate if the equipment is not returned in the original packaging and with correct
documentation for a claim to be processed. All claims are at the sole discretion of Adam Equipment.
This warranty does not cover equipment where defects or poor performance is due to misuse, accidental damage,
exposure to radioactive or corrosive materials, negligence, faulty installation, unauthorised modifications or
attempted repair, or failure to observe the requirements and recommendations as given in this User Manual.
This product may include a rechargeable battery that is designed to be removed and replaced by the user. Adam
Equipment warrants that it will provide a replacement battery if the battery manifests a defect in materials or
workmanship during the initial period of use of the product in which the battery is installed.
As with all batteries, the maximum capacity of any battery included in the product will decrease with time or use,
and battery cycle life will vary depending on product model, configuration, features, use, and power management
settings. A decrease in maximum battery capacity or battery cycle life is not a defect in materials or workmanship,
and is not covered by this Limited Warranty.
Repairs carried out under the warranty do not extend the warranty period. Components removed during warranty
repairs become company property.
The statutory rights of the purchaser are not affected by this warranty. The terms of this warranty is governed by
the UK law. For complete details on Warranty Information, see the terms and conditions of sale available on our
web-site.

EN
© Adam Equipment Company 2014 1 8 (P.N. 3136611622 - Revision D, Apr 2014)
This manual covers the details of operation. If you have a problem with the
scale that is not directly addressed by this manual then contact your supplier
for assistance. In order to provide further assistance, the supplier will need
the following information which should be kept ready:
A.
Details of your company
- Name of your company:
- Contact person’s name:
- Contact telephone, e-mail,
- Fax or any other methods:
B. Details of the unit purchased
(This part of information should always be available for any future
correspondence. We suggest you to fill in this form as soon as the unit is
received and keep a print-out in your record for ready reference.)
Model name of the scale:
Serial number of the unit:
Software revision number
(Displayed when power is first turned
on):
Date of Purchase:
Name of the supplier and place:
C. Brief description of the problem
Include any recent history of the unit. For example:
-Has it been working since it’s delivered
-Has it been in contact with water
-Damaged from a fire
-Electrical Storms in the area
-Dropped on the floor, etc.