Adaptec ARO-1130SA Assembly Instructions

R
Installation and Hardware Guide
ARO-1130SA
RAID Option Card
for PC Servers
with RAIDport I or II

Adaptec, Inc.
691 South Milpitas Boulevard
Milpitas, CA 95035
© 1998 Adaptec, Inc.
All rights reserved. Adaptec, and the Adaptec logo are trade-
marks of Adaptec, Inc. which may be registered in some
jurisdictions.
Printed in Singapore
STOCK NO.: 511930-00, Rev. A RQ 3/98
R

R
▼ ▼ ▼ ▼ ARO-1130SA
RAID Option Card
for PC Servers
with RAID
port I or II
Installation and Hardware Guide

ii
Copyright
© 1998 Adaptec, Inc. All rights reserved. No part of this publication may be repro-
duced, stored in a retrieval system, or transmitted in any form or by any means, elec-
tronic, mechanical, photocopying, recording or otherwise, without the prior written
consent of Adaptec, Inc., 691 South Milpitas Blvd., Milpitas, CA 95035.
Trademarks
Adaptec, the Adaptec logo, AHA, AIC, ARO, Array1000, CI/O, RAIDport, RAIDport II,
ArrayConfig, and SCSISelect are trademarks of Adaptec, Inc. which may be registered
in some jurisdictions. Windows and Windows 95 are registered trademarks and Win-
dows NT is a trademark of Microsoft Corporation in the U.S. and other countries used
under license. All other trademarks are owned by their respective owners.
Changes
The material in this document is for information only and is subject to change with-
out notice. While reasonable efforts have been made in the preparation of this docu-
ment to assure its accuracy, Adaptec, Inc. assumes no liability resulting from errors or
omissions in this document, or from the use of the information contained herein.
Adaptec reserves the right to make changes in the product design without reservation
and without notification to its users.
Disclaimer
IF THIS PRODUCT DIRECTS YOU TO COPY MATERIALS, YOU MUST HAVE PER-
MISSION FROM THE COPYRIGHT OWNER OF THE MATERIALS TO AVOID VIO-
LATING THE LAW WHICH COULD RESULT IN DAMAGES OR OTHER
REMEDIES.

iii
Federal Communications Commission Radio Frequency Interference Statement
WARNING: Changes or modifications to this unit not expressly approved by the party responsi-
ble for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy, and if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. However, if this equipment does cause
interference to radio or television equipment reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/television technician for help.
Use a shielded and properly grounded I/O cable and power cable to ensure compliance of this
unit to the specified limits of the rules.
This device complies with part 15 of the FCC rules. Operation is subject to the following two con-
ditions: (1) this device may not cause harmful interference and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Canadian Compliance Statement
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matérial
brouilleur du Canada.
Adaptec, Inc. ARO-1130B
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE

v
▼ ▼ ▼ ▼ Contents
1 Introduction
System Requirements 1-2
Installation Overview 1-3
2 Installing ARO-1130SA Hardware
ARO-1130SA Layout 2-2
Verifying Presence of DIMM Memory 2-3
Installing the ARO-1130SA 2-4
Connecting the LED Cable to the ARO-1130SA 2-5
Completing the Installation 2-6
3 Using the Array1000xA BIOS & Driver Selection
Utility
Running the Array1000xA BIOS & Driver Selection
Utility 3-2
4 Creating the First Array With the Array
Config
SA
Utility
Creating an Array 4-2
Making the Array Bootable 4-5
5 Installing Software on a Windows NT Server
Installing the Array1000xA Driver for Windows NT 5-2
Installing the Driver When Installing Windows NT 5-2
Installing the Driver When Windows NT is Already
Installed 5-4
Installing Adaptec CI/O Management Software for
Windows NT Server 5-5

vi
ARO-1130SA Installation and Hardware Guide
6 Installing Software on a Novell NetWare Server
Installing the Array1000SA Driver for Novell NetWare 6-2
Installing the Driver When Installing NetWare 6-2
Installing the Driver When NetWare is Already
Installed 6-5
Installing the TIRPC Communications Module 6-6
NetWare 3.12 6-6
NetWare 4.11 6-6
Installing the Adaptec CI/O Management Software for
Novell NetWare 6-7
Adaptec CI/O Management Software Installation
Hints 6-8
7 Installing Software on a Remote Client
Installing Adaptec CI/O Management Software 7-2
Hints for Establishing Communications With Your
Server 7-3
A Configuring ARO-1130SA with the SCSI
Select
Utility
Starting the SCSISelect Utility A-2
Using SCSISelect Menus A-2
Exiting SCSISelect A-3
Using the SCSI Disk Utilities A-3
SCSISelect Settings A-4
SCSI Bus Interface Definitions A-4
SCSI Device Configuration A-5
Additional Options A-6

vii
Contents
B Using the ARO-1130SA with Other Adaptec
Products
Using Driver Disk B B-2
Using the ARO-1130SA with an AHA-294x, AHA-3940, or
Other AIC-78x0 Based Host Adapter and Driver Disk B
(Windows NT Only) B-2
Scenario #1: Adding an ARO-1130SA to a RAIDport I or
II System with an AHA-294x, AHA-3940, or Other
AIC-78x0 Based Host Adapter B-3
Scenario #2: Adding an AHA-294x, AHA-3940, or Other
AIC-78x0 Based Host Adapter to a RAIDport I or II
System with an ARO-1130SA B-6
Backing up the Windows NT Registry B-10
C Troubleshooting
Troubleshooting Checklist C-1
Problems Running the Software On Your Windows NT
Server C-2
Problems Running SNMP Agent on Your Windows NT
Server C-4
D Using a CD-ROM Drive
Using a CD-ROM Drive with DOS D-1
Using a CD-ROM Drive with NetWare D-5
E Using the SNMP Agent
NetWare E-1
Windows NT E-2
Loading MIBs in the MIB Database E-3
Index
❒