Adaptec 2Gb SANbloc Series User manual

18F
18F
18F
18F
18F
18F
18F
18F
18F
18F
18F
18F
18F
18F
0
1
2
3
4
5
SAN bloc
Series
0
1
2
3
4
5
2
Gb
2Gb SANbloc Series
Quick Installation Guide
Unpacking and Installation
Cabling and Configuration
Getting More Information
1
2
3
September 2003
Revision: 1.1
P/N: MAN-FC2002-QUIK

Section 1: Unpacking and Initial Setup
NOTE: Before removing any of the components, ensure that anti-static precautions
have been taken. The minimum requirement is an anti-static wrist strap and ground-
ing wire.
STEP 1. Remove all the components from the packaging and place on an anti-static
surface until you are ready to use them.
STEP 2. Install the disk drives, power supplies and advanced cooling modules into
the enclosure in the locations shown below (install rackmount enclosures in
rack before installing components):
1
2
1
2
0
I
0
I
Disk Drives LSM
LSM
ACMs
Power Supplies I/O Module
I/O Module
18F
18F
18F
18F
18F
18F
18F
18F
18F
18F
18F
18F
18F
18F
0
1
2
3
4
5
SAN bloc
Series
0
1
2
3
4
5
2
Gb
2

Section 2: Cabling and Configuration
Each of the fourteen disk drive slots of the 2Gb SANbloc Series has a unique iden-
tifier assigned to it. This identifier is assigned using a combination of the Slot
number and the enclosure ID.
The enclosure ID is set, using the enclosure ID switch, located on the rear of the
enclosure.
This enclosure ID switch can be set to 0 through 7. The graphic below shows the
slot number and location.
1
2
1
2
0
I
0
I
Enclosure ID
Switch
1
LSM LSM
Slot 13 Slot 12 Slot 11
Slot 10 Slot 9 Slot 8 Slot 7 Slot 6 Slot 5 Slot 4 Slot 3 Slot 2 Slot 1 Slot 0
Slot location when viewed from the front of the enclosure
3

The fourteen disk drive slots (0 to 13), will be assigned an identifier based on the
enclosure ID and the slot number as shown in the following table.
Disk Drive Identifier Table
Enclosure
ID
Drive Slot 01234567
Slot 0 3 183348637893108
Slot 1 4 193449647994109
Slot 2 5 203550658095110
Slot 3 6 213651668196111
Slot 4 7 223752678297112
Slot 5 8 233853688398113
Slot 6 9 243954698499114
Slot 7 10 25 40 55 70 85 100 115
Slot 8 11 26 41 56 71 86 101 116
Slot 9 12 27 42 57 72 87 102 117
Slot 10 13 28 43 58 73 88 103 118
Slot 11 14 29 44 59 74 89 104 119
Slot 12 15 30 45 60 75 90 105 120
Slot 13 16 31 46 61 76 91 106 121
4

Supported Cables
WARNING: Only the following APPROVED cables must be used with the 2Gb SAN-
bloc Series enclosures.
This section lists the cables that must be used with the 2GB SANbloc Series enclo-
sure. Failure to adhere to these guidelines may cause the enclosure to operater in-
correctly.
Copper Cables
Only the following AMPHENOL copper Fibre Channel cables must be used with
the 2Gb SANbloc Series enclosure (copper applications).
Amphenol Cable Model Numbers:
Optical Cables
The optical Fibre Channel cables used with the 2Gb SANbloc Series enclosure
must conform to the following:
• Minimum Length: 2 Meters
• Maximum Length: 150 Meters
Model No. Description
515840001 .3m 2Gb Fibre Channel, copper cable, non-equalized, HSSDC-HSSDC
515840003 1m 2Gb Fibre Channel, copper cable, non-equalized, HSSDC-HSSDC
515840007 3m 2Gb Fibre Channel, copper cable, non-equalized, HSSDC-HSSDC
515840013 6m 2Gb Fibre Channel, copper cable, non-equalized, HSSDC-HSSDC
5

2Gb SANbloc Series (JBOD)
STEP 1. Attach the cables provided with your enclosure. The illustrations below
show the configuration for dual fibre channel loop systems. Daisy chaining
configurations is also shown.
NOTE: When enclosures are daisy chained, each enclosure must have a different
enclosure ID.
Connecting Dual
FC Loop Mode
Daisy Chaining
Enclosures with
Dual I/O Modules
1
2
1
2
0
I
0
I
To HBA To HBA
1
2
1
2
0
I
0
I
To HBA
1
2
1
2
0
I
0
I
To next
enclosure
To HBA
To next
enclosure
6

STEP 2. Attach the power cords provided, to the power connectors on each of the two
power supplies on the rear of the enclosure.
1
2
1
2
0
I
0
I
Insert Power cords into
power connectors
AC Power
Connection
7

2 Gb SANbloc Series Quad Loop
NOTE: Quad loop configuration requires that the enclosure be configured in split
loop mode. To set split loop mode, a jumper must be installed at jumper location
JP3 on each LS module in the enclosure.
This section describes the procedure for connecting the enclosure in quad loop
mode. For this configuration there must be two LS modules and two I/O modules
installed in the enclosure.
STEP 1. Remove both LS modules from the enclosure and install a jumper at jumper
location JP3 if one is not already installed. This sets the enclosure to operate
in split loop mode.
STEP 2. Attach cables to the top and bottom connector of both I/O modules.
STEP 3. Attach the other end of these four cables to your host systems.
NOTE: Enclosures in split loop mode can not be daisy chained to other enclosures.
1
2
1
2
0
I
0
I
To HBA To HBA
To HBA To HBA
8

STEP 4. Attach the power cords provided, to the power connectors on each of the two
power supplies on the rear of the enclosure.
1
2
1
2
0
I
0
I
Insert Power cords into
power connectors
AC Power
Connection
9

Section 3: Getting More Information
For more information on installing and configuring your enclosure, refer to the
“2Gb SANbloc Series Installation Guide” (on the Documentation CD).
To obtain Technical Support for the 2Gb SANbloc Series contact our World Wide
Support Centre at:
Telephone:[phone] (RAID, FC, External Storage)
408-934-7274 (Hardware)
E-mail:ask.adaptec.com
WWW http://www.adaptec.com/support
10