Adaptec ULTRAbloc 320 JBOD User manual

ULTRAbloc 320 JBOD
Quick Installation Guide
P/N: MAN-SC2100-QUIK
Revision: 1.7
September 2003
1
2
3
Unpacking and Installation
Cabling and Configuration
Getting More Information
1
2
3

Section 1: Unpacking and Initial Setup
NOTE: Before removing any of the components, ensure that anti-static precautions
have been taken. The minimum requirement is an anti-static wrist strap and ground-
ing wire.
STEP 1. Remove all the components from the packaging and place on an anti-static
surface until you are ready to use them.
STEP 2. Install the disk drives, power supplies and advanced cooling modules into
the enclosure in the locations shown below (install rackmount enclosures in
rack before installing components):
1
2
1
2
0
I
0
I
Mute
Disk Drives LED
ACMs
Power Supplies I/O Module
I/O Module
1
2
3
Module
2

Section 2: Cabling and Configuration
SCSI ID Assignments
The SCSI ID’s for the ULTRAbloc Series enclosure are hard set and cannot be
changed in anyway. The ULTRAbloc Series enclosure has two modes of operation:
Single (Joined) SCSI bus mode (1x14), and Dual (Split) SCSI bus mode (1x7 and
1x7). The I/O Modules are set at ID 15 in all cases and SCSI ID 7 is reserved for
the host. The illustration below show how the SCSI ID’s are assigned.
ID 0
ID 1
ID 2
ID 3
ID 4 ID 5 ID 6
ID 8
ID 9 ID 10 ID 11
ID 12 ID 13 ID 14
Single (Joined)
Bus Mode
ID 8
ID 9
ID 10
ID 11
ID 12
ID 13
ID 14
Dual (Split)
Bus Mode
Both rear I/O Modules are at SCSI ID 15 in all configurations
Bus A
Bus B
1
2
3
ID 8
ID 9
ID 10
ID 11
ID 12
ID 13
ID 14
3

ULTRAbloc Series JBOD Configurations
STEP 1. Attach the cables provided with your ULTRAbloc Series enclosure. The
illustrations below show the configurations and how to cable them.
1
2
1
2
0
I
0
I
To Host
ID 7
ESM TSM
(Joiner Module
may be used also)
Mute
01
23
4
5
6
8
9
10
11
121314
15 15
ID
ID
IDID
ID
ID
ID
ID
ID
ID
ID
ID
ID
ID
ID
ID
DiskDisk
Disk
Disk
Disk
Disk
DiskDisk
Disk
Disk
Disk
DiskDiskDisk I/O
Module
I/O
Module
SCSI ID Assignments shown from front of enclosure
1
2
1
2
0
I
0
I
To Host
ID 7
To Host
ID 7
ESM TSM
(Terminator Module
may be used also)
Mute
89
10
11
12
13
14
8
9
10
11
1213
14
15 15
ID
ID
IDID
ID
ID
ID
ID
ID
ID
ID
ID
ID
ID
ID
ID
Disk
Disk
Disk
Disk
Disk
Disk
DiskDisk
Disk
Disk
Disk
DiskDiskDisk I/O
Module
I/O
Module
SCSI ID Assignments shown from front of enclosure
BUS A
BUS B
Single/Joined
SCSI Bus
Dual/Split
SCSI Bus
4

NOTE: Both I/O modules are at ID 15. Only one module will be active at any one
time and the other will be in standby mode. If the active I/O module fails the stand-
by will take over.
STEP 2. Attach the power cords provided, to the power connectors on each of the two
power supplies on the rear of the enclosure.
1
2
1
2
0
I
0
I
Insert Power cords into
power connectors
Mute
AC Power
Connection
5

ULTRAbloc Series Dual CSM Configuration
STEP 1. Attach the cables provided with your ULTRAbloc Series enclosure. The
illustration below shows how the configuration should be cabled.
1
2
1
2
0
I
0
I
To Cluster 1 Master Host
To Cluster 1 Slave Host
CSM CSM
To Cluster 2 Slave Host
To Cluster 2 Master Host
Mute
Bus A
Bus B Bus A
Bus B
89
1011
12
13
14
8
9
10
11
12
13
14
15 15
ID
ID
IDID
ID
ID
ID
ID
ID
ID
ID
ID
ID
ID
ID
ID
Disk
Disk
Disk
Disk
Disk
Disk
DiskDisk
Disk
Disk
Disk
DiskDiskDisk I/O
Module
I/O
Module
SCSI ID Assignments shown from front of enclosure
BUS B BUS A
6

STEP 2. Attach the power cords provided, to the power connectors on each of the two
power supplies on the rear of the enclosure.
1
2
1
2
0
I
0
I
Insert Power cords into
power connectors
Mute
AC Power
Connection
7

Section 3: Getting More Information
For more information on installing and configuring your ULTRAbloc Series Enclo-
sure refer to the “ULTRAbloc 320 JBOD User Guide” (on the documentation CD).
To obtain Technical Support for the ULTRAbloc Series contact our World Wide
Support CentreMonday-Friday 3am to 5pm Pacific at:
Telephone:[phone] (RAID, FC, External Storage)
408-934-7274 (Hardware)
E-mail:ask.adaptec.com
WWW http://www.adpatec.com/support
8