Addonics Technologies HD9SITDRHS User manual

Technical Support
If you need any assistance to get your unit functioning properly, please have your
product information ready and contact Addonics Technical Support at:
Hours: 8:30 am - 6:00 pm PST
Phone: [phone]
Email: http://www.addonics.com/support/query/
v3.1.11
www.addonics.com
User Guide
1:9 HS HDD Duplicator Pro
(HD9SITDRHS)
T E C H N O L O G I E S

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: [phone] Email: www.addonics.com/support/query/
Drive InstallationGuide
Step 1
Use a Philips screwdriver to
turn the cover securing screw
clockwise into the "OPEN"
position.
Step 2
Slide the aluminum cover towards
the back end of the Diamond
enclosure and remove it.
Step 3
For SATA Drive:
Carefully place the SATA hard
drive with the label facing up into
the Diamond Enclosure. Push
the hard drive towards the back
end to secure the drive connec-
tors onto the Diamond
enclosure’s SATA connector.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: [phone] Email: www.addonics.com/support/query/
For IDE Drive
Note: Configure your IDE hard
drive as Master device
Connect the 4-Pin Molex cable to
the power connector on the IDE
hard drive. Carefully place the IDE
hard drive with the label facing up
into the Diamond enclosure. Push
the hard drive toward the back
end to secure the drive connectors
onto the Diamond enclosure’s IDE
connector.
Step 4
Turn the Diamond enclosure over
with the hard drive mounting holes
facing up. Use the included flat
head screws to secure the hard
drive onto the bottom of the enclo-
sure and turn in the screw to the
“LOCK” position.
Step 5
Insert the enclosure into a cradle in
the duplicator and secure it in place
with the handle and turn the cradle's
lock to the LOCK position. Note: the
drive will not power up until the
cradle's lock is in the LOCK posi-
tion.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: [phone] Email: www.addonics.com/support/query/
Connecting the Power Cable and Powering On
a.Connect the power cord provided from the wall outlet tothe back of the tower.
b. Turn on the main power switch on the rear of the chassis.
c. Push the power button on the front of the unit to turn on the HDD duplicator.
There are four buttons and an LCD on the panel of HDD Duplicator.
1 – LCD shows a function or a message.
2 – it is used to scroll up function menus.
3 – it is used to scroll down function menus.
4 – it is used to execute a function.
5 – it is used to cancel a function.
Duplicator Panel
ENT
ESC
2
3
4
5
1

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: [phone] Email: www.addonics.com/support/query/
Main Menu
1. Copy HDD
Scans the ports, then copies from the source to any targets found.
2. Async Copy HDD
Scans the ports, then copies from the source to any targets found. More
drives may be added before the process is complete, they will begin the
process as soon as they are detected.
3. Compare HDD
Scans the ports, then any targets found will be compared to the source.
4. Async Compare
Scans the ports, then any targets found will be compared to the source.
More drives to compare may be added before the process is complete,
they will begin the process as soon as they are detected.
Quick Start
By default, the duplicator will initialize, scan for drives and offer the
copy function. Insert the source and target drives, power up the unit,
wait for the copy function to appear, then press ENT.
Canceling Functions
When selecting menu options, canceling is done by pressing ESC.
When the unit is busy performing an operation such as copy, verify,
or overwrite, the operation can be canceled by holding the ESC
button until the unit beeps.
Duplicator Functions
The duplicator has three menu sections: The Main menu, Setup
Options, and Advanced Setup Options. Setup Options is accessed
through the Main menu. Advanced Setup Options is accessed by
holding the ESC button from any other menu until the unit beeps.
When the duplicator completes some of the functions it will record a
log of the most recent activity. Select VIEW LOG from the Main
Menu to review the latest function's results.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: [phone] Email: www.addonics.com/support/query/
5. PreScan Source
Reads all blocks on the source drive to confirm no I/O errors are encoun-
tered.
6. ReScan BUS
Manually scans all ports and reports how many units were found.
7. Source Size
Examines the source drive and reports total space and space used, if
drive contains compatible partitions. Press up/down to change display,
ESC to exit.
8. Secure Erase
Scans all ports, then erases all data on all connected drives.
NOTE: some drives will remain in a locked state when the process is
complete. Drives that are locked may not appear to an operating system
and will cause an I/O error if used as a target in the duplicator. If this
happens, start secure erase again and hold ESC to cancel the operation
a few moments after it begins.
9. Overwrite
Overwrite is used to write data onto the entire hard disk, it will destroy all
data on all HDDs connected to the duplicator (including Source HDD) by
writing data to all sectors. There are 4 sub-options: One pass (zero), One
pass (random), 3 pass and 7 pass.
10. Setup
Enters the Setup menu. See Setup Options.
11. View Log
Shows the results from the most recent drive operation, such as copy,
overwrite, etc.
12. Adv Setup
Enters the Advanced Setup Menu. Only available by holding ESC on any
Main Menu option. See Advanced Setup Options.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: [phone] Email: www.addonics.com/support/query/
Setup options
10-1. Language
Use this option to select the language of the system, currently only Eng-
lish is supported.
10-2. Copy Size
Controls how much of the source drive to use for copy operations, in
percentage. Default setting is ALL (100%).
10-3. Startup Menu
Sets the first menu option to appear after boot. Default setting is Copy
HDD.
10-4. Auto Compare
Controls whether or not targets are compared automatically when copy is
complete. Default setting is OFF.
10-5. Button Sound
Enables audible beep when pressing buttons. Default setting is ON.
10-6. Device Info
Displays information about connected drives. Main display is drive manu-
facturer and size. Press up/down to select drives, ENT to display model
number and firmware revision of selected drive.
10-7. System Info
Displays firmware version and date.
10-8. Fast Copy
When this setting is ON, the duplicator will attempt to copy the source
drive's contents instead of the entire disk. Also controls Compare function.
Default setting is OFF.
NOTE: Target drive size is still required to be equal to or greater than
source. Only works with source drives formatted using Master Boot
Record. If the source drive has a boot record other than MBR, the entire
disk will be copied as if Fast Copy were OFF. If the source drive is format-
ted with a Master Boot Record and contains only FAT32 or NTFS parti-
tions, identical partitions will be created on the target(s) and only the files
will be copied. If the source drive with MBR format includes partitions
other than FAT32 or NTFS, all sectors of all partitions (including FAT32
and NTFS) will be duplicated.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: [phone] Email: www.addonics.com/support/query/
10-9. Auto Start Drive
When source drive is present, inserting a target drive will cause copy
process to begin automatically. Default setting is OFF.
10-10. Auto Start Timer
Sets delay in time after target insertion before beginning auto copy
process if Auto Start Drive is ON. Default setting is OFF (no delay).
10-11. Tolerance Size
Sets the minimum target size in percentage compared to the source that
is allowed to use for copying. Default is 100% (equal in size).
NOTE: Leaving this setting at 100% or using for minor adjustments only
is strongly recommended. Permitting target size less than source size
may result in inaccurate copies.
10-12. BootTime Delay
This option is used to set boot delay time. Default setting is 5 seconds.
10-13. Quick Compare
Sets Compare function to stop after a small amount of data has been
verified, up to 100MBytes. Default setting is OFF.
10-14. Copy with Size
Causes duplicate drive to report to an operating system the exact same
total size as source when copy is complete. Works only on drives format-
ted using a Master Boot Record. Default setting is OFF.
Advanced Setup Options
12-01. Read Error Skip
Allows duplicator to ignore I/O errors while reading source drive. Default
setting is OFF.
12-02. Update Firmware
Used to apply firmware updates. Connect a drive formatted as FAT
containing one partition with the firmware file in the root directory.
NOTE: This function scans the entire disk before proceeding. Providing a
drive that is as small as possible is strongly recommended.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: [phone] Email: www.addonics.com/support/query/
12-03. Compare Firmware
Used to confirm correct firmware. Connect a drive formatted as FAT
containing one partition with the firmware file in the root directory.
NOTE: This function scans the entire disk before proceeding. Providing
a drive that is as small as possible is strongly recommended.
12-04. Quick Erase HDD
Scans the ports, then quickly erases all sectors on all connected drives.
12-05. Full Erase HDD
Scans the ports, then completely erases all sectors on all connected
drives.
12-06. H/W Diagnostic
Starts comprehensive tests for Ram, LCD, buttons, ports and Flash.
12-07. Load Default
Resets all configuration settings to default.
12-08. Copy HPA
Enables copy functions to duplicate the source drive's Host Protected
Area. Normally this area is defined as not available to a host controller
as defined by ATA/SATA specifications.
12-09. Burn In
Runs a function continuously until aborted. Selections are Copy &
Compare, Compare, Async Cpy & Cmp, Async Compare.

www.addonics.com
Phone: [phone]
Fax: [phone]
Email: http://www.addonics.com/sales/query/
CONTACT US