ADEMCO Alarm System Instruction manual

Ademco Alarm System
Quick User Guide
Arming & Disarming the System
Arming (Turning on)
Close all sensors (i.e. close doors and windows). The Ready indicator should be on. Arm the system
using either of the methods below.
AWAY mode: Enter your access code + AWAY (2 button).
STAY mode: Enter your access code + STAY (3 button).
Note: If motion detectors have not been installed on the alarm system, there is no difference in
arming in STAY or AWAY mode.
Disarming (Turning off)
Enter your access code + OFF (1 button) to disarm anytime the system is armed. The keypad will
beep if you walk through the entry door. Enter your code within 45 seconds to avoid an alarm
condition.
Open Zones
If you do not have a Ready light, press 4to view open zone(s). Close door or window and check for
ready light. If motion detector is open, stop movement and check for ready light. Once you have
ready light, proceed with arming process.
Bypassing Zones
Use the zone bypassing feature when you want to arm the system, but skip a zone that you want to
leave open or requires service. Bypassed zones will not be able to sound an alarm.
Zones cannot be bypassed once the system is armed. Bypassed zones are automatically cancelled
each time the system is disarmed and must be bypassed again, if required, before the next arming.
Bypass
1. Enter code + BYPASS (6 button).
2. Enter zone number(s) to be bypassed (use 2-digit entry).
3. Proceed with arming.
Quick Bypass (automatically bypasses all open zones)
1. Enter code + BYPASS (6 button).
2. Proceed with arming.
Alarm Memory
When an alarm occurs, the keypad displays Alarm in Memory along with zone number.
Enter code + OFF (1 button) to clear.
Sensor Reset
Certain sensors (such as smoke detectors and glass break detectors) have to be reset after an alarm.
To reset enter Code + OFF, Code + OFF.
Note: If unable to reset, call your alarm company for service.
Ademco Quick User Guide Page 1
ADE8

Access Codes
All Ademco panels have different instructions for adding, deleting or changing Master Access Code or
User Access Codes. See specific User Manuel for your model of control panel for detailed
instructions.
Chime Mode
Your system can alert you to the opening of a door while it is disarmed by using the CHIME feature.
When activated, three beeps will sound at the keypad whenever a door is opened.
Enter Code + CHIME (9 button) to turn chime feature on and off.
CHIME will appear in display when feature is turned on.
Trouble Conditions
When a trouble condition is detected, the word CHECK appears on the keypad display, accompanied
with rapid “beeping” at the keypad. Press any key to silent beeps. Use the chart below to determine
the trouble condition.
CHECK + zone Zone or sensor is not functioning properly.
Action:Check sensor or contact and verify it is intact. If no obvious problem
found, call for service.
TELCO FAULT The system has detected no dial tone on phone line.
(or CHECK
Zone 94) Action:If telephones do not have dial tone, call Phone Company for service. If
phones are working, call Alarm Company for service.
COMM FAILURE The system attempted to send a signal to the monitoring company, but failed.
(or FC) This may be related to TELCO FAULT.
Action:If Telco Fault is also active, follow steps above first. Once phone line
problem corrected, the only way to clear this trouble is to send signal to
monitoring company. Put system into test with monitoring company or alarm
company, arm system, set off alarm, after 10-20 seconds of siren enter code to
disarm.
SYSTEM LO Panel back-up battery is low.
BAT (or BAT
with no zone #) Action:If this appears along with power failure, allow 2 hours after power returns
to allow panel to recharge. If trouble remains, replace battery.
AC LOSS Panel has lost power.
(or NO AC)
Action:If building/house has power, but panel has no power, call for service.
LO BAT + Wireless transmitter has a low battery.
zone (or BAT
with zone #) Action:Replace battery or batteries.
If any above troubles do not clear automatically or after correction is made, call for service.
Ademco Quick User Guide Page 2
ADE8