Adexa HBS-300L User manual

MEAT SLICER
INSTRUCTION MANUAL
Model
MEAT SLICER
HBS-300L ●HBS-300A ●HBS-275A ● HBS-250L ● HBS-250A ●
HBS-220A
ADEXA DIRECT LIMITED
GROUND FLOOR UNIT 1 214 PURLEY WAY CROYDON CR0 4XG LONDON UNITED KINGDOM
T: [phone] [e-mail] www.adexa.co.uk

INTRODUCTION:
You should read this user manual carefully before using the appliance.
This appliance is intended for commercial use only and must not be used for
household use.
The appliance must only be used for the purpose for which it was intended and
designed.
Consult Local and National Standards to comply with the following:
Health and Safety at Work Legislation
BS EN Codes of Practice
Fire Precautions
IEE Wiring Regulations
Building Regulations
The manufacturer is not liable for any damage caused by incorrect operation
and improper use.
Keep the appliance and electrical plug away from water and any other liquids. In
the event that the appliance should fall into water, immediately remove plug
from the socket and do not use until the appliance has been checked by a
certified technician.
Failure to follow these instructions could cause a risk to lives.
Never attempt to open the casing of the appliance yourself.
Do not insert any objects in the casing of the appliance.
Do not touch the plug with wet or damp hands.
Danger of electric shock! Do not attempt to repair the appliance yourself. In
case of malfunctions, repairs are to be conducted by qualified personnel only.
Never use a damaged appliance! Disconnect the appliance from the electrical
outlet and contact the retailer if it is damaged.
Warning! Do not immerse the electrical parts of the appliance in water or other
liquids.
Never hold the appliance under running water.
Regularly check the power plug and cord for any damage. If the power plug or
power cord is damaged, it must be replaced by a service agent or similarly
qualified persons in order to avoid danger or injury.

Make sure the cord does not come in contact with sharp or hot objects and keep
it away from open fire. To pull the plug out of the socket, always pull on the plug
and not on the cord.
Ensure that the cord (or extension cord) is positioned so that it will not cause a
trip hazard.
Always keep an eye on the appliance when in use.
Warning! As long as the plug is in the socket the appliance is connected to the
power source.
Turn off the appliance before pulling the plug out of the socket.
Never carry the appliance by the cord.
Do not use any extra devices that are not supplied along with the appliance.
Only connect the appliance to an electrical outlet with the voltage and
frequency
mentioned on the appliance label.
Connect the power plug to an easily accessible electrical outlet so that in case of
emergency the appliance can be unplugged immediately.
To completely switch off theappliance pull the power plug out of the electrical
outlet.
Always turn the appliance off before disconnecting the plug.
EN
Never use accessories other than those recommended by the manufacturer.
Failure to do so could pose a safety risk to the user and could damage the
appliance.
Only use originalparts and accessories.
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge.
This appliance must not be used by children under any circumstances.
Keep the appliance and its cord out of reach of children.
Always disconnect the appliance from the mains if it is left unattended or is not
in use,and before assembly, disassembly or cleaning.
Never leave the appliance unattended during use.

SPECIAL SAFETY REGULATIONS:
• This appliance should be operated on a level, horizontal, dry, stable and heat
resistant surface.
• This appliance should be operated by trained personnel.
• The user must wear close-fitting dressing during operation. Scarf is not
allowed.
• Do not use the appliance to slice frozen food, meat that has not been
deboned, fish or anynon-food products.
• Though the appliance has built-in safety features, keep away from the blade
and movingparts at all times.
• Stop using the appliance as soon as the blade’s diameter has become thinner
than 6 mm. replace the blade.
PRODUCT DESCRIPTION:
HBS220A Meat Slicer with 220mm blade diameter
HBS250A Meat Slicer with 250mm blade diameter
HBS275A Meat Slicer with 275mm blade diameter
HBS300A Meat Slicer with 300mm blade diameter
HBS250L Meat Slicer with 250mm blade diameter Premium design
HBS300L Meat Slicer with 300mm blade diameter Premium design

CONTENTS:
Slicer parts
1 Blade sharpener
2 Stop plate
3 Carriage
4 On/off switch
5 Slice thickness dial
6 Product clamp
7 Blade guard
8 Blade
9 Carriage lock
10 Blade guard bolt (not displayed)
9

Top view of the appliance
Attach the sharpening module in such a way that the blade does not move
between the wheels.
Secure the sharpening device to the machine by tightening the holder. Check to
make sure that the sharpening device is well secured before using the machine.
NOTE! The sharpening device is equipped with a safety switch. If the sharpening device
is not properly at- tached, you will not be able to use the appliance.

ASSEMBLY:
The plastic safety guard has been removed from the appliance to prevent damage
during transit.
Safety guard must be fitted before using the machine.
Adexa accept no responsibility for any injury caused by operation of this appliance
without the guard installed or correctly fitted.
1. Place both screws in the carriage.
2. Attach the hand guard

3. Place the two washers over the bolts.
4.Screw on the two dome nuts.

Operation.
1. Connect the appliance to the power supply
2. Set the thickness to the desired level by turning the Thickness knob anti-clockwise.
3. Place the meat in the cradle and secure in place with the Grip handle.
4. Switch On the power [I].
Warning: Never use your hands to secure the meat when slicing.
5. Holding the carriage and grip handles, push the carriega backwards and forwards
across the blade.
Warning: The blade starts immediately.
6. After slicing the desired amount press the off button to turn off the Appliance.
Warning: The balde continues to turn for a few seconds after switching off.
7. Remove the sliced food from the catchment area.
Warning: Always disconnet the meat slicer from the mains power supply when not in
use.

NL
SAFE BLADE REMOVAL TOOL
The blade cleaning must be carried out with metal gloves and a wet cloth!
Unplug the slicer from the power supply.
Remove the blade guard cover by unscrewing the pin at the back of the appliance.
Place and fit the supplied blade removal tool with the notch at the right top side.
Rotate and align the 2 screw holes on the blade with the 2 screw handles of the blade
removal tool.
Then, screw and tighten 2 handles of the blade removal tool into the blade and locking it
into place.
Unscrew the screws that fasten the blade to the appliance.
Lift the blade removal tool with the 2 handles to remove the blade.
Keep the blade removal tool in place when clean- ing.
Refit and reinstall the blade in reverse after cleaning.

CLEANING , CARE AND MAINTENANCE:
• Always turn off and disconnect the appliance from
the power supply before cleaning.
• Always use extreme care when handling the blade.
• Use soapy water and a damp cloth to clean the appliance.
• Clean the appliance regularly.
Cleaning the Blade and Cover
1. Disconnect the appliance from the power supply.
2. Push the carriage away from the blade.
3. Unscrew the blade cover release bolt.
Blade cover release bolt

4. Carefully lift off the blade cover.
5. Attach the blade removal tool by placing it over the blade and screweing two
bolts into the corresponding holes in the balde.
6.Unscrew the 3 screws holding the blade, leaving it sat on the slicer.
7.Lift the blade off the slicer using the knobs of the blade removal tool as handles.
8.Wash the blade by wiping from the centre towards the edge. Keep the removal tool
in place when cleaning. If necessary, wipe clean the face of the blade once it has been
reattached.
9. Dry thoroughly.
10.Replace the blade and cover, ensuring the blade securing bolt is securely tightened.
We recommend the use of cut-resistant wire mesh gloves when cleaning the blade.

SHARPENING THE BLADE:
If the meat slicer begins to produce uneven or broken slices, it may be blunt and
require sharpening. To sharpen the blade:
To sharpen the blade:
1. Unscrew the Sharpener release bolt and lift off the blade sharpener.
2. Rotate the sharpener 180° and insert it back into the appliance.
3. Tighten the Sharpener release bolt to secure the sharpener.
4. Start the appliance.
5. Press and hold down the rear sharpening stone button to sharpen the blade. Do
not exceed one minute of constant sharpening.
6. Release the rear stone and press down the front sharpening stone button for a few
seconds to smooth the edge of the blade.
7. Turn off the appliance and return the sharpener to its original position, ensuring it
is securely tightened.
FRONT SHARPENING STONE
BUTTON
SHARPENER RELEASE BOLT
REAR SHARPENING STONE
BUTTON

LUBRICATING THE PUSHER AXLE:
1. Push the carriage to one side and clean the axle with a dry cloth.
2. Lubricate the axle surface with grease suitable for use in food
preparation areas.
3. Push the carriage backwards and forwards several times to distribute
the grease evenly.
Carriage knob
CARRIAGE KNOB
PUSHER AXLE

TROUBLESHOOTING:
Problem
Possible cause
Solution
Appliance does not slice well
Blunt blade
Sharpen blade
Dirty appliance
Clean the appliance
Appliance stops slicing
Overheated motor
Let the machine cool off for an
extended period. The motor’s
safetythermostatwillresetitself
automatically.
Carriage does not slide
Dirty slide bar
Cleantheslidebarandlubricate
with food grade oil.
Blade stops when product is
being cut
v-belt worn out or dirty
Replace or clean the v-belt

Technical Specifications
Model:
HBS300L
HBS250L
HSB-300A
Voltage
220-240V 50HZ
220-240V 50HZ
220-240V 50HZ
Power
250W
150W
250W
Slicing
thickness
0~15mm
0~12mm
0~15mm
Blade
diameter
300mm
250mm
300mm
Max slicing
width
22mm
18mm
22mm
Weight
22.30KGS
16.40KGS
21.10KGS
Measurement
597x520x495MM
537x460x400MM
597x520x495MM
Noise Level
< 70 dB
< 70 dB
< 70 dB
Protection
Class
CLASS I
CLASS I
CLASS I
Model:
HBS275A
HBS-250A
HBS-220A
Voltage
220-240V 50HZ
220-240V 50HZ
220-240V 50HZ
Power
250W
150W
120W
Slicing
thickness
0~15mm
0~12mm
0~12mm
Blade
diameter
275mm
250mm
220mm
Max slicing
width
22mm
18mm
16mm
Weight
18.50KGS
15.50KGS
14.40KGS
Measurement
567x490x465MM
537X460X400MM
498X435X380MM
Noise Level
< 70 dB
< 70 dB
< 70 dB
Protection
Class
CLASS I
CLASS I
CLASS I

ELECTRICAL WIRING
This appliance is supplied with a 3 pin, moulded, BS1363 plug and lead, with a 3 amp
fuse as standard. The plug is to be connected to a suitable mains socket.
This appliance is wired as follows:
•Live wire (coloured brown) to terminal marked L
•Neutral wire (coloured blue) to terminal marked N
•Earth wire (coloured green/yellow) to terminal marked E
This appliance must be earthed, using a dedicated earthing circuit. If in doubt consult
a qualified electrician.
Electrical isolation points must be kept clear of any obstructions. In the event of any
emergency disconnection being required they must be readily accessible.

SPARE PART LIST