ADJ H2O DMX IR User manual

User Manual
H2O DMX IR
Rev. 01/2021

©2021 ADJ Products, LLC all rights reserved. Information, specications, diagrams, images, and
instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying
product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection
claimed includes all forms and matters of copyrightable materials and information now allowed by
statutory or judicial law or hereinafter granted. Product names used in this document may be trade-
marks or registered trademarks of their respective companies and are hereby acknowledged. All
non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of their
respective companies.
ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,
equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic
loss associated with the use or reliance of any information contained within this document, and/or as
a result of the improper, unsafe, insucient and negligent assembly, installation, rigging, and opera-
tion of this product.
Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical products when
they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power
when not in use. Thank you!
ADJ Products, LLC - www.adj.com - H2O DMX IR User Manual Page 2

ADJ Products, LLC - www.adj.com - H2O DMX IR User Manual Page 3
Introduction: Thank you for purchasing the H2O DMX IR by ADJ Products, LLC. The H2O DMX IR is
an improvement of the very popular H2O DMX LED. This new unit has better optics and brighter LED
output producing vibrant colors. The unit can now be controlled using the ADJ UC IR. The unit has 3
operating modes: show mode, manual mode & DMX Controlled. It can be used as a stand alone unit
or in a primary-secondary conguration. This unit is suitable for theaters, studios, retail stores, and
other similar locations.
Unpacking: Every H2O DMX IR has been thoroughly tested and has been shipped in perfect operat-
ing condition. Carefully check the shipping carton for damage that may have occurred during ship-
ping. If the carton appears to be damaged, carefully inspect your unit for any damage and be sure all
accessories necessary to operate the system have arrived intact. In the event damage has been found
or parts are missing, please contact our toll free customer support number for further instructions.
Please do not return the system to your dealer without rst contacting customer support.
Customer Support: ADJ Products, LLC provides a toll free customer support line, to provide set up
help and to answer any questions should you encounter problems during your set up or initial opera-
tion. You may also visit us on the web at www.adj.com for any comments or suggestions. Service
Hours are Monday through Friday 8:00 a.m. to 4:30 p.m. Pacic Standard Time.
Voice: [phone]
Fax: [phone]
E-mail: [email protected]
To purchase parts online visit parts.adj.com.
Warning! To prevent or reduce the risk of electrical shock or re, do not expose this unit to rain or
moisture.
Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself,
doing so will void your manufacturer’s warranty. In the unlikely event your unit may require service
please contact ADJ Products, LLC.
PLEASE recycle the shipping carton when ever possible.
H2O DMX IR Introduction

ADJ Products, LLC - www.adj.com - H2O DMX IR User Manual Page 4
H2O DMX IR General Instructions
To optimize the performance of this product, please read these operating instructions carefully to
familiarize yourself with the basic operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please keep this manual with the unit for
future reference.
• Includes Built-In Hanging Yoke
• 5 Colors Plus White & Split Colors
• Manually Control Color, Rotation Speed, & Dimmer
• 37 Degree Lens & Optional 27 Degree Lens
• Power Cord Daisy Chain Capability (See Power Cord Daisy Chain section of this manual)
• ADJ UC IR Compatible (Sold Separately)
The H2O DMX IR carries a two year (730 days) limited warranty. Please fill out the enclosed war-
ranty card to validate your purchase. All returned service items, whether under warranty or not, must
be freight pre-paid and accompany a return authorization (R.A.) number. The R.A. number must be
clearly written on the outside of the return package. A brief description of the problem as well as the
R.A. number must also be written down on a piece of paper and included in the shipping container. If
the unit is under warranty, you must provide a copy of your proof of purchase invoice. You may obtain
an R.A. number by contacting customer support at [phone].
H2O DMX IR Warranty Registration
H2O DMX IR Features
The unit should be mounted using a mounting clamp (not provided), which should be affixed to the
mounting bracket that is provided with the unit. Always ensure that the unit is firmly fixed to avoid
vibration and slipping while operating. Always ensure that the structure to which you are attaching the
unit is secure and is able to support at least 10 times the weight of the unit. Also always use a safety
cable that can hold 12 times the weight of the unit when installing the fixture.
The equipment must be installed by a professional, and it must be installed in a place where it is out
of the reach of people’s grasp.
H2O DMX IR Installation

ADJ Products, LLC - www.adj.com - H2O DMX IR User Manual Page 5
H2O DMX IR Safety Precautions
• To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture.
• Do not spill water or other liquids into or on to your unit.
• Do not attempt to operate this unit if the power cord has been frayed or broken. Do not attempt
to remove or break off the ground prong from the electrical cord. This prong is used to reduce the
risk of electrical shock and fire in case of an internal short.
• Disconnect from main power before making any type of connection.
• Do not remove the cover for any reason. There are no user serviceable parts inside.
• Never operate this unit with the cover removed.
• Never plug this unit in to a dimmer pack.
• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6”
(15cm) between this device and a wall.
• Do not attempt to operate this unit if it has been damaged in any way.
• This unit is intended for indoor use only. Use of this product outdoors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power-supply cords should be routed so that they are not likely to be walked on or pinched by
items placed upon or against them, paying particular attention to the point at which they exit from
the unit.
• Cleaning - The fixture should be cleaned only as recommended by the manufacturer. See the
Cleaning section of this manual for details.
• Heat - The appliance should be situated away from heat sources such as radiators, heat registers,
stoves, or other appliances (including amplifiers) that produce heat.
• The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen onto, or liquid has been spilled into, the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a marked change in perfor-
mance.

H2O DMX IR DMX Set Up
ADJ Products, LLC - www.adj.com - H2O DMX IR User Manual Page 6
Power Supply: The ADJ H2O DMX IR contains an automatic voltage switch, which will automati-
cally sense the voltage when it is plugged into the power source. With this switch there is no need to
worry about the correct power voltage, allowing this unit to be plugged in anywhere.
DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of commu-
nication between intelligent xtures and controllers. A DMX controller sends DMX data instructions
from the controller to the xture. DMX data is sent as serial data that travels from xture to xture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX xtures (most controllers only
have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of dierent manufacturers to be
linked together and operate from a single controller, as long as all xtures and the controller are DMX
compliant. To ensure proper DMX data transmission, try to use the shortest cable path possible
when linking several DMX xtures. The order in which xtures are connected in a DMX line does not
inuence the DMX addressing. For example, a xture assigned a DMX address of 1 may be placed
anywhere in a DMX line: at the beginning, at the end, or anywhere in the middle. When a xture is
assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that
unit, no matter where it is located in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX Operation): The H2O DMX IR is a three chan-
nel DMX unit. The DMX address is set on the top panel of the H2O DMX IR. Your unit and your DMX
controller require an approved DMX-512 110 Ohm Data cable for data input and data output. We
recommend Accu-Cable DMX cables. If you are making your own cables, be sure to use standard
110-120 Ohm shielded cable (This cable may be purchased at almost all professional sound and
lighting stores). Your cables should be made with a male and female XLR connector on either end of
the cable. Also remember that DMX cable must be daisy chained and cannot be split.

ADJ Products, LLC - www.adj.com - H2O DMX IR User Manual Page 7
Notice: Be sure to follow gures two and three when making your own cables. Do not use the
ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug
or allow the shield conductor to come in contact with the XLR cable’s outer casing. Grounding the
shield could cause a short circuit and erratic behavior.
Special Note: Line Termination. When longer runs of cable are used, you may need to use a termi-
nator on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor which
is connected between pins 2 and 3 of a male XLR connector (DATA+ and DATA-). This unit is inserted
in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable
terminator (ADJ part number Z-DMX/T) will decrease the chances of erratic behavior.
5-Pin XLR DMX Connectors. Some manufacturers use 5-pin DMX-512 data cables for DATA trans-
mission in place of 3-pin. 5-pin DMX xtures may be implemented in a 3-pin DMX line. When insert-
ing standard 5-pin data cables in to a 3-pin line a cable adaptor must be used. These adaptors are
readily available at most electric stores. The chart below details a proper cable conversion.
H2O DMX IR DMX Set Up

H2O DMX IR System Menu
ADJ Products, LLC - www.adj.com - H2O DMX IR User Manual Page 8

ADJ Products, LLC - www.adj.com - H2O DMX IR User Manual Page 9
On-Board System Menu. The H2O DMX IR comes with an easy to navigate system menu. This next
section will detail the functions of each command in the system menu. Please read the next section
thoroughly!
To access the main menu press the MENU button. Press the UP or DOWN buttons until you reach
function you wish to change. When you reach the function you wish to change press the ENTER
button. When a function is selected use the UP or DOWN buttons to change the func-tion settings.
Once your changes are made press the ENTER button, and then press and hold the MENU button
for at least three seconds to conrm and lock the change into the system memory. If the MENU but-
ton is not pressed and held within eight seconds the xture will automatically conrm and lock the
change into the system memory. To exit without making any changes press the MENU button.
DMX Address - This will let you set your desired DMX address.
1. Press the MENU button until “DMX Address” is displayed, and press ENTER.
2. The current DMX address will be displayed. Press the UP or DOWN buttons to nd your desired
address.
3. Press ENTER to conrm, then connect your DMX controller.
Show Mode - Show modes 1-3 (Factory programs). Show mode can run with or without sound
active mode.
1. Press the MENU button until “Show Mode” is displayed, and press ENTER.
2. “Show X” will now be displayed, “X” representing a number between 1-3. Use the UP or DOWN
buttons to nd your desired show.
3. When you have found your desired show press ENTER, then press and hold the MENU button
for at least 3 seconds to activate. After you have set your desired show, it can be changed at any
time using the UP or DOWN buttons.
Pri/Sec Mode - This will let you set the unit as a primary or secondary unit in a primary/sec-
ondary conguration.
1. Press the MENU button until “Pri/Sec Mode” is displayed, and press ENTER. Either “Pri.”,
“Sec. 1”, or “Sec. 2” will be displayed.
2. Press the UP or DOWN buttons until your desired setting is displayed, and press ENTER to con-
rm.
H2O DMX IR System Menu

ADJ Products, LLC - www.adj.com - H2O DMX IR User Manual Page 10
H2O DMX IR System Menu
DMX State - This mode denes the behavior of the xture in the event that the DMX signal is
lost or interrupted. It also denes the mode that the xture will default to when power is rst
connected.
1. Press the MENU button until “DMX State” is displayed, and press ENTER. The current last state
setting will be displayed.
2. Use the UP or DOWN buttons to nd a mode you would like the unit to go into in case the DMX
signal is lost.
• Pri Sec - If the DMX signal is lost or power is applied, the unit will automatically go into Pri-
mary Secondary mode and run a built-in show.
• Blackout - If the DMX signal is lost or interrupted, the unit will automatically go into stand by
mode.
• Last State - If the DMX signal is lost the xture will stay in the last DMX setting. If power is
applied and this mode is set, the unit will automatically go into the last DMX set up.
3. Press ENTER to conrm your desired set up.
Back Light - With this function the display back light will turn o after 2 minutes.
1. Press the MENU button until “Back Light” is displayed, and press ENTER.
2. Either “ON” or “OFF” will now be displayed. Press the UP or DOWN buttons to select “ON” to
keep the LED display on at all times, or “OFF” to allow the LED display to turn o after 2 minutes.
Press any button to turn on the LED display again.
3. Press ENTER, and then press and hold the MENU button for at least three seconds to conrm.
Manual Mode - This function will let you manually test the color wheel, water wave, and dim-
mer. In this function you can also manually adjust and set the color wheel, rotation speed, and
dimmer.
1. Press the MENU button until “Manual Mode” is displayed, and press ENTER.
2. Use the UP or DOWN buttons to scroll between “Color”, “Wave”, or “Dimmer”. Select the func-
tion you would like to test and press ENTER.
3. Use the UP or DOWN buttons to adjust the values in order to test/check the function. Press the
MENU button after testing the functions.
4. Manual Mode can also be used to manually congure that xture display. In this case, the user
may simply leave the xture in Manual Mode after dialing in the desired conguration.
Auto Test - This function will run a self test program.
1. Press the MENU button until “Auto Test” is displayed, and press ENTER.
2. The xture will now run a self test. Press the MENU button to exit
Fixture Temp. - With this function you can display the xture temperature.
1. Press the MENU button until “Fixture Temp.” is displayed, and press ENTER.
2. The xture temperature will now be displayed. Press the MENU button to exit.
Fixture Hours - With this function you can display the running time of the unit.
1. Press the MENU button until “Fixture Hours” is displayed, and press ENTER.
2. The running time of the xture will now be displayed. Press the MENU button to exit.