ADJ ikon profile ww User manual

User Manual
IKON PROFILE WW
Rev. 01/2021

©2021 ADJ Products, LLC all rights reserved. Information, specications, diagrams, images, and
instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying
product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection
claimed includes all forms and matters of copyrightable materials and information now allowed by
statutory or judicial law or hereinafter granted. Product names used in this document may be trade-
marks or registered trademarks of their respective companies and are hereby acknowledged. All
non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of their
respective companies.
ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,
equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic
loss associated with the use or reliance of any information contained within this document, and/or as
a result of the improper, unsafe, insucient and negligent assembly, installation, rigging, and opera-
tion of this product.
Europe Energy Saving Notice
Energy Saving Matters (EuP 2009/125/EC)
Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical products when
they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power
when not in use. Thank you!
ADJ Products, LLC - www.adj.com - Ikon Prole WW User Manual Page 2

ADJ Products, LLC - www.adj.com - Ikon Prole WW User Manual Page 3
To optimize the performance of this product, please read these operating instructions carefully to
familiarize yourself with the basic operations of this unit. These instructions contain important safety
information regarding the use and maintenance of this unit. Please keep this manual with the unit for
future reference.
Unpacking: Thank you for purchasing the Ikon Prole WW by ADJ Products, LLC. Every Ikon Prole
WW has been thoroughly tested and has been shipped in perfect operating condition. Carefully check
the shipping carton for damage that may have occurred during shipping. If the carton appears to be
damaged, carefully inspect your unit for any damage and be sure all equipment necessary to operate
the system has arrived intact. In the event damage has been found or parts are missing, please con-
tact our toll free customer support number for further instructions. Please do not return the unit to your
dealer without rst contacting customer support.
Customer Support: ADJ Products, LLC provides a toll free customer support line, to provide set up
help and to answer any questions should you encounter problems during your set up or initial opera-
tion. You may also visit us on the web at www.adj.com for any comments or suggestions. Service
Hours are Monday through Friday 8:00 a.m. to 4:30 p.m. Pacic Standard Time.
Voice: [phone]
Fax: [phone]
E-mail: [email protected]
Warning! To prevent or reduce the risk of electrical shock or re, do not expose this unit to rain or
moisture.
Caution! This may cause eye damage. Avoid looking directly into the light source. Use sensible pre-
caution.
Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself,
doing so will void your manufacturer’s warranty. In the unlikely event your unit may require service
please contact ADJ Products, LLC.
PLEASE do not discard the shipping carton in the trash. Please recycle when ever possible.
Ikon Profile WW Introduction

ADJ Products, LLC - www.adj.com - Ikon Prole WW User Manual Page 4
The Ikon Profile WW carries a two year (730 days) limited warranty. Please fill out the enclosed war-
ranty card to validate your purchase. All returned service items, whether under warranty or not, must
be freight pre-paid and accompany a return authorization (R.A.) number. If the unit is under warranty
you must provide a copy of your proof of purchase invoice. Please contact ADJ customer support for
an R.A. number.
Ikon Profile WW Precautions
Ikon Profile WW Warranty Registration
Safety Issue: This unit may blow the fuse if the maximum allotted load of 2 amps is reached. If the
fuse needs replacement, please see the section of this manual for Fuse Replacement for directions.
• Be sure the local power outlet match the required voltage of the unit.
• Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user serviceable parts inside.
• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6”
(15cm) between this device and a wall.
• To reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture.
• This unit is intended for indoor use only. Use of this product outdoors voids all warranties.
• During long periods of non-use, disconnect the unit’s main power.
• Always mount this unit in safe and stable matter.
• Power Cord Protection - Power-supply cords should be routed so that they are not likely to be
walked on or pinched by items placed upon or against them, paying particular attention to cords
at plugs, convenience receptacles, and the point where they exit from the fixture.
• Do not attempt to remove or break off the ground prong from the electrical cord. This prong is
used to reduce the risk of electrical shock and fire in case of an internal short.
• The fixture should be serviced by qualified service personnel when:
A. The power cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into, the appliance.
C. The appliance has been exposed to rain or water.
D. The fixture does not appear to operate normally or exhibits a marked change in performance.

ADJ Products, LLC - www.adj.com - Ikon Prole WW User Manual Page 5
Ikon Profile WW Fixture Layout
1. LED:
DMX On DMX input present
PRIMARY On Primary Mode
SECONDRY On Secondary Mode
2. Button:
MENU Select the displayed function
UP Scroll backward through function list
DOWN Scroll forward through function list
ENTER Confirm the selected function
3. Fuse (T 2A): Protects the unit from overcurrent damage.
4. Display: Shows the various menus and selected functions.
5. Power In/Out: Power cable input/output connections.
6. DMX In/Out: 3-pin XLR connections the DMX-512 operation.
7. Flags: Used to adjust the gobo framing.
8. Knobs: Used to adjust the beam angle and focus the gobo.
9. Spring: Locks the color gel frame into place.

Ikon Profile WW System Menu
ADJ Products, LLC - www.adj.com - Ikon Prole WW User Manual Page 6

ADJ Products, LLC - www.adj.com - Ikon Prole WW User Manual Page 7
On-Board System Menu. The Ikon Prole WW comes with an easy to navigate system menu. This
next section will detail the functions of each command in the system menu. Please read the next
section thoroughly!
To access the main menu press the MENU button. Press the UP or DOWN buttons until you reach
the desired function, press the ENTER button to select. Once a function is selected, use the UP or
DOWN buttons to change the function settings. Once your changes are made press the ENTER
button, and then press and hold the MENU button for at least three seconds to conrm and lock the
change into the system memory. If the MENU button is not pressed and held within eight seconds,
the xture will automatically conrm and lock the change into the system memory. To exit without
making any changes press the MENU button.
ADDR - DMX Address Setting
1. Press the MENU button until “ADDR” is displayed, and press ENTER.
2. The current DMX address will now be displayed and ashing. Press the UP or DOWN buttons to
nd your desired address. Press ENTER to set your desired DMX address.
NOTE: If after you connect your DMX controller the unit does not fall into DMX mode, press and hold
the MENU button for at least 3 seconds.
SCND - This will let you set unit as a primary or secondary in a primary/secondary congura-
tion.
1. Press the MENU button until “SCND” is displayed, and press ENTER. “Prl” or “SEC” will be dis-
played.
2. Press the UP or DOWN buttons until your desired setting is displayed, press ENTER to conm
and exit.
DNST - This mode denes how the xture will behave in the event that DMX communication is
lost or interrupted.
1. Press the MENU button until “DNST” is displayed, and either “Pr Se”, “BLND”, or “LAST” will be
displayed beneath.
2. Press ENTER and the bottom choice will begin to ash. Use the UP or DOWN buttons to choose
an operating mode you would like the unit to start up in when power is applied or the DMX signal
is lost.
• PrSe (Primary-Secondary) - If the DMX signal is lost or power is applied, the unit will auto-
matically go into Primary/Secondary mode and run a built-in show.
• BLND (Blackout) - If the DMX signal is lost or interrupted, the unit will automatically go into
stand by mode.
• LAST - If the DMX signal is lost the xture will stay in the last DMX setting. If power is ap-
plied and this mode is set, the unit will automatically go into the last DMX set up.
3. Press ENTER to conrm your desired set up.
Ikon Profile WW System Menu

ADJ Products, LLC - www.adj.com - Ikon Prole WW User Manual Page 8
Ikon Profile WW System Menu
DIND - This will let select your desired dimmer curve.
1. Press the MENU button until “DIND” is displayed, and press ENTER. 1 of 5 dimmer curves will be
displayed. “STDA” (standard), “STGE” (stage), “TV” (TV), “ARAL” (Architectural), or “THAL” (The-
atre).
2. Press the UP or DOWN buttons to nd your desired dimmer curve and press ENTER to conm
and exit.
LED - With this function the LED display will turn o after 2 minutes.
1. Press the MENU button until “LED” is displayed, and press ENTER.
2. The display will show either “ON” or “OFF”. Press the UP or DOWN buttons to select “ON” to
keep the LED display on at all times, or “OFF” to allow the LED display to turn o after 2 minutes.
Press any button to turn on the LED display again.
3. Press ENTER to conrm and exit.
DISP - This function will reverse the display 180º.
1. Press the MENU button until “DISP” is displayed, and press ENTER.
2. Press the UP button to select “DISP” to activate this function, or “DSIP” to deactivate this func-
tion.
3. Press ENTER to conrm.
MANU - In this submenu you are able to test the dimmer and strobe.
1. Press the MENU button until “MANU” is displayed, and press ENTER.
2. Use the UP and DOWN buttons to scroll through the various functions able for testing. Once you
have found your desired function, press ENTER.
3. After you have pressed ENTER, use the UP and DOWN buttons to adjust the values and test the
function. To exit press the MENU button.
TEST - This function will run a self test program.
1. Press the MENU button until “TEST” is displayed, and press ENTER.
2. The xture will now run a self test.
TEMP - With this function you can check the temperature of the xture.
1. Press the MENU button until “TEMP” is displayed, and press ENTER.
2. The xture temperature will now be displayed. Press MENU to exit.
FHRS - With this function you can display the running time of the unit.
1. Press the MENU button until “FHRS” is displayed, and press ENTER.
2. The display shows the running time of the unit. Press MENU to exit.
VER - Use this function to display the Software version of the unit.
1. Press the MENU button until “VER” is displayed, and press ENTER.
2. The display will show the software version.

ADJ Products, LLC - www.adj.com - Ikon Prole WW User Manual Page 9
Ikon Profile WW DMX Values & Traits
Ikon Profile WW CAD Drawing

ADJ Products, LLC - www.adj.com - Ikon Prole WW User Manual Page 10
Ikon Profile WW Gobo Replacement
The Ikon Prole WW gobo can be interchanged at any time, allowing you to customize your system.
To replace gobo:
1. Gently slide the gobo housing out of the top of unit. The gobo housing is located in front of the
top ag.
2. Once the gobo housing has been removed, remove the retaining ring that holds the gobo in. This
can easily be done using needle nose pliers.
3. Remove and replace the gobo with your desired replacement. Reinsert the retainer ring, and
make sure the ring rests rmly against the gobo.
4. Slide the gobo assembly back into place.
Ikon Profile WW Adding a Color Gel
A color gel (not included) can be added to the front of the Ikon Prole WW and can be interchanged
at any time. This allows you to customize your system.
To add a color gel:
1. Locate the color gel frame at the front of the unit. Slide the spring lever back and slide the gel
frame out of the holder.
2. Once the gel frame has been removed slide your desired color gel into the middle of the frame.
3. Slide the spring back and slide the gel frame into place.