ADLINK Technology NuPRO-775 Series User manual

NuPRO-775 Series
Half Size Socket-370
Pure PCI Industrial SBC
User’s Guide
Recycled Paper

Copyright Notice
Manual Rev 2.10: August 8, 2001
Part NO: 50-13017-202
This publication is protected by copyright and all rights are reserved. No
part of it may be reproduced or transmitted by any means or in any form,
without prior consent of the original manufacturer.
The information in this document has been carefully checked and is
believed to be accurate. However, the original manufacturer assumes no
responsibility for any inaccuracies that may appear in this manual. In no
event will the original manufacturer be liable for direct, indirect, special,
exemplary, incidental or consequential damages resulting from any
defect or omission in this manual, even if advised of possibility of such
damages. The material contained herein is for informational purposes
only.
Acknowledgments
Award is a registered trademark of Award Software International, Inc.
IBM and PS/2 are trademarks of International Business Machines
Corporation.
Intel and Pentium are registered trademarks of Intel Corporation.
Microsoft Windows is a registered trademark of Microsoft Corporation.
All other product names or trademarks are properties of their respective
owners.

Getting service from ADLINK
♦Customer Satisfaction is always the most important thing for
ADLINK Tech Inc. If you need any help or service, please contact us
and get it.
ADLINK Technology Inc.
Web Site http://www.adlink.com.tw
Sales & Service [email protected]
NuDAQ + USBDAQ [email protected]
NuDAM [email protected]
NuIPC [email protected]
NuPRO [email protected]
Technical
Support
Software [email protected]
TEL [phone] FAX [phone]
Address 9F, No. 166, Jian Yi Road, Chungho City, Taipei, 235 Taiwan, R.O.C.
♦Please inform or FAX us of your detailed information for a prompt,
satisfactory and constant service.
Detailed Company Information
Company/Organization
Contact Person
E-mail Address
Address
Country
TEL FAX
Web Site
Questions
Product Model
OS :
Computer Brand :
Environment to Use
M/B : CPU :
Chipset : BIOS :
Video Card :
Network Interface Card :
Other :
Challenge Description
Suggestions to ADLINK

Table of Contents •i
Table of Contents
Chapter 1 Introduction ................................................ 1
1.1 Checklist.............................................................................1
1.2 Description .........................................................................2
1.3 Features.............................................................................3
1.4 Specifications.....................................................................4
1.5 Intelligence.........................................................................7
Chapter 2 Installations .............................................. 10
2.1 CPU Installation ...............................................................10
2.2 Memory Installation..........................................................11
2.3 Jumpers on the NuPRO-775............................................11
2.4 Connectors on the NuPRO-775.......................................12
2.5 Watchdog Timer Configuration ........................................21
Chapter 3 BIOS Configuration .................................. 24
3.1 BIOS Introduction.............................................................25
3.2 BIOS Setup ......................................................................25
Chapter 4 Intel 810 Chipset Hardware
Configuration & Driver Installation......... 52
4.1 Hardware Configuration File Installation..........................52
4.2 VGA Driver Installation.....................................................54
Chapter 5 LAN Driver Installation Guide.................. 56
5.1 Introduction ......................................................................56
5.2 Features...........................................................................56
5.3 Software Drivers Support.................................................57
5.4 Running Diagnostics ........................................................57
Hardware Doctor Utility .............................................. 61
Product Warranty/Service .......................................... 66

Introduction •1
1
Introduction
This manual is designed to give you information on the NuPRO-775 CPU
board.
The topics covered in this chapter are as follows:
•Checklist
•Description
•Features
•Specifications
•Intelligence
•Layout of Key Components and Dimensions
1.1 Checklist
Please check that your package is complete and contains the items below.
If you discover damaged or missing items, please contact your dealer.
•The NuPRO-775 Industrial Computer Main Board
•This User’s Manual
•1 IDE Ribbon Cable
•1 Floppy Ribbon Connector
•2 Serial Port Ribbon Cable and 1 Parallel Port Attached to a
Mounting Bracket
•1 Optional 2-port USB cable

2 •Introduction
•1 CD Containing hardware configuration file, VGA Driver, Intel
82559 LAN Driver and Hardware Monitor utility
1.2 Description
The NuPRO-775 is a Celeron/Pentium III Industrial Computer Main board
based on the Intel i82810 chipset and is fully designed for harsh industrial
environment. It features a Socket-370 processor connector that is
compatible with Intel Celeron/Pentium III processors. This board
accommodates up to 256MB SDRAM configuration.
The NuPRO-775 comes with Winbond’s W83627HF Super I/O chip. The
embedded hardware monitoring device that monitors system and CPU
temperature, system voltages, and CPU and chassis fan speeds to prevent
system crashes by warning the user of adverse conditions. NuPro775 also
has a case-open indicator for security.

Introduction •3
1.3 Features
•Intel Celeron 300~533MHz, Pentium III 500E/550E, or later version
processors
•Bus Speed 66/100MHz
•Intel i82810 chipset(built-in VGA controller)
•Up to 256MB SDRAM system memory
•Two 16550 UART compatible ports with RS-232 interface
•High speed bi-directional SPP/ECP/EPP parallel port
•Programmable watchdog timer
•Hardware Monitoring
•Modem ring-in
•10/100 Base-T Ethernet interface
•Wake On LAN

4 •Introduction
1.4 Specifications
•Processor Socket: Socket-370 connector
•Processor: Intel Celeron 300~533MHz, Pentium III 500E/550E, or
later version
•Bus Speed: 66/100MHz
•Chipset: Intel i82810
•Secondary Cache: built in CPU
•Memory Sockets:
One 168-pin DIMM socket
Max. 256MB SDRAM
Memory type: PC-100 unbuffered DIMM
•Integrated Graphics Controller:
3D Graphics Visual Enhancement
24-bit 230 MHz RAMDAC
DDC2B compliant
Up to 1600x1200 in 8-bit color at 85Hz refresh
•BIOS: Award BIOS, PnP support
Intel 82802AB Firmware Hub(512KB) for BIOS update
Power management
Y2K Compliant
•DMI BIOS Support:
Desktop Management Interface (DMI) allows users to download
system hardware-level information such as CPU type, CPU speed,
internal/external frequencies and memory size.
•Super I/O: Winbond W83627HF
•Parallel Port:
One high-speed parallel port, SPP/EPP/ECP mode
ESD protection to 4KV
Downstream device protection to 30V
•Serial Port:
Two 16550 UART compatible ports with RS-232 interface

Introduction •5
ESD protection to 2KV
•Enhanced IDE: Bus Master IDE controller, two EIDE interfaces for
up to four devices, support PIO Mode 3/4 or Ultra DMA/66 IDE Hard
Disk and ATAPI CD-ROM.,LS120,ZIP
•FDD Interface: Two floppy drives (360KB, 720KB, 1.2MB, 1.44MB,
2.88MB)
•CRT:
On-board VGA Controller
Built-in AGP2X (3D hyper pipelined architecture)
RAMDAC Latch-up protection
•USB Interface:
Two USB pin-header connectors, compliant with USB Specification
Rev. 1.1
Individual over-current protection
•Watchdog Timer: programmable
Programmable I/O port 2Eh and 2Fh to configure watchdog timer
Time-out timing select 0~255 seconds/minutes
•Green Function: Power management via BIOS, activated through
mouse/keyboard movement
•PCI Bus Ethernet Interface:
Intel 82559 chipset
PCI local bus Ethernet controller
IEEE 802.3 10base-T and 100base-TX compatible physical longer
support
IEEE802.3u auto-negotiation support for automatic speed selection
10/100Mbps operation in a single port PCI bus master architecture
IEEE 802.3X (100base-TX Flow control support)
Wake on Lan support
Optional Alert on LAN II support
Management communication support to reduce the total cost of
ownership (TCO)
•Keyboard and Mouse Connectors: PS/2 type mini-DIN that
supports PC/AT; supports a 5-pin external keyboard connector

6 •Introduction
•PCI Compliance: Fully compliant to PCI rev. 2.1 standards
•Power supply: ATX
•Environmental and Mechanical:
Power Consumption: +5V@10A(max), +3.3V@10A(max),
[email protected], -12V@130mA, [email protected]
Temperature: 0°C to 70°C
Humidity: 5% to 95%
Dimensions: 185mm x 122mm

Introduction •7
1.5 Intelligence
•System Health Monitoring: A sensor for the CPU temperature on
the NuPRO-775 monitors the CPU temperature, an external sensor
for system temperature, case-opened indicator, fan-speed
detection, system voltages monitoring
•Windows 98 shut-off: Allows shut-off control from within Windows
98 and through an ATX power supply.
•Modem ring-in: Allows system powering on through an external
modem and through an ATX power supply.
•Year 2000 Compliant BIOS: The onboard Award BIOS is Year
2000 Compliant
•Wake On LAN: Through an ATX power supply and network
connection, systems can be turned on from the power-off state.
•Alert on LAN II : Allows SOS hardware event alert, watchdog, and
Advanced Power Management (APM) through Ethernet.

8 •Introduction
Figure 1 Layout of key components:

Introduction •9
Figure 2 NuPRO-775 Mechanical Drawing

10 •Installations
2
Installations
This chapter provides information on how to use the jumpers and
connectors on the NuPRO-775 in order to set up a workable system. The
topics covered are:
•CPU Installation
•Memory Installation
•Jumpers on the NuPRO-775
•Connectors on the NuPRO-775
•Watchdog timer configration
2.1 CPU Installation
The NuPRO-775 industrial computer Main board supports a Socket-370
processor socket for Intel Celeron, Pentium III processors.
Before inserting the CPU, make sure the notch on the corner of the CPU
corresponds with the notch on the inside of the socket.
After you have installed the processor into place, check if the jumpers for
the CPU type and speed are correct.
Note: Ensure that the CPU heat sink and the CPU top surface are in
total contact to avoid CPU overheating problem that would
cause your system to hang or be unstable.

Installations •11
2.2 Memory Installation
The NuPRO-775 industrial computer main board supports one 168-pin
DIMM socket for a maximum total memory of 256 MB. The memory
modules can come in sizes of 16MB, 32MB, 64MB, 128MB, and 256MB
SDRAM.
2.3 Jumpers on the NuPRO-775
The jumpers on the NuPRO-775 allow you to configure your main board
according to the needs of your applications. If you have doubts about the
best jumper configuration for your needs, contact your dealer or sales
representative. The figure and table below show the correct setting to match
the CPU frequency.
CPU Frequency SDRAM
Frequency JP1 JP2
66 100 1-2 2-3
100 100 2-3 2-3
66/100 auto 100 3-4 2-3
Reserved for future 1-2
♦JP3: Power button
♦JP4: Standby power connector

12 •Installations
2.4 Connectors on the NuPRO-775
The connectors on the NuPRO-775 allow you to connect external devices
such as keyboard, floppy disk drives, hard disk drives, printers, etc. The
following tables list the connectors on NuPRO-775 and their respective
functions.
CN1: Floppy Drive Connector..............................................................14
CN2, CN3: EIDE Connectors...............................................................15
CN2: Secondary IDE Connecto:..........................................................16
CN4, CN5: Serial Port (CN5 : COM1, CN4 : COM2)...........................17
CN9: Parallel Port Connector ..............................................................18
CN13: PS/2 Mouse Connector ............................................................19
CN14: VGA CRT Connector................................................................19
CN15: RJ45 Connector .......................................................................19
FN1: CPU Fan Power Connector ........................................................20
LED1: LAN Activity Indicators..............................................................20

Installations •13
Figure 3 Connector location on the NuPRO-775

14 •Installations
CN1: Floppy Drive Connector
CN1 is a 34-pin header and will support up to 2.88MB floppy drives.
Signal Name Pin# Pin# Signal Name
Ground 1 2
Drive density
selection
Ground 3 4 No connect
Ground 5 6
Drive density
selection
Ground 7 8 Index
Ground 9 10 Motor enable 0
Ground 11 12 Drive select 1
Ground 13 14 Drive select 0
Ground 15 16 Motor enable 1
Ground 17 18 Direction
Ground 19 20 Step
Ground 21 22 Write data
Ground 23 24 Write gate
Ground 25 26 Track 00
Ground 27 28 Write protect
Ground 29 30 Read data
Ground 31 32 Side 1 select
Ground 33 34
Diskette
change