ADLINK Technology NuPRO-865 User manual

Recycled Paper
NuPRO-865
Full-Size SBC
User’s Manual

©Copyright 2004 ADLINK Technology Inc.
All Rights Reserved.
Manual Rev. 1.00: July 23, 2004
Part No.:
The information in this document is subject to change without prior notice in
order to improve reliability, design, and function and does not represent a
commitment on the part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special,
incidental, or consequential damages arising out of the use or inability to use
the product or documentation, even if advised of the possibility of such
damages.
This document contains proprietary information protected by copyright. All
rights are reserved. No part of this manual may be reproduced by any
mechanical, electronic, or other means in any form without prior written
permission of the manufacturer.
Trademarks
NuDAQ®, NuIPC®, NuDAM®, NuPRO®are registered trademarks of ADLINK
Technology Inc. Other product names mentioned herein are used for
identification purposes only and may be trademarks and/or registered
trademarks of their respective companies.

Getting Service from ADLINK
Customer Satisfaction is top priority for ADLINK Technology Inc. If you need
any help or service, please contact us.
ADLINK TECHNOLOGY INC.
Web Site http://www.adlinktech.com
Sales & Service [email protected]
TEL [phone] FAX [phone]
Address 9F, No. 166, Jian Yi Road, Chungho City, Taipei, 235 Taiwan
Please email or FAX your detailed information for prompt, satisfactory, and
consistent service.
Detailed Company Information
Company/Organization
Contact Person
E-mail Address
Address
Country
TEL FAX
Web Site
Questions
Product Model
Environment
OS:
Computer Brand:
M/B: CPU:
Chipset: BIOS:
Video Card:
NIC:
Other:
Detail Description
Suggestions for ADLINK

Introduction •i
Table of Contents
Chapter 1 Introduction..................................................................1
1.1 Unpacking Checklist........................................................................ 2
1.2 Features.......................................................................................... 4
1.3 System Block Diagram.................................................................... 5
1.4 Specifications.................................................................................. 6
Chapter 2 Installation....................................................................9
2.1 System Installation.......................................................................... 9
2.2 Board Layout................................................................................. 14
2.3 Jumper setting............................................................................... 15
2.4 Connectors Description................................................................. 16
2.5 Optional IP-ALCS20 Audio Card................................................... 27
Chapter 3 Award BIOS Setup.....................................................29
3.1 BIOS Instructions.......................................................................... 29
3.2 Main Menu .................................................................................... 29
3.3 Standard CMOS Features............................................................. 31
3.4 IDE Adaptors................................................................................. 34
3.5 Advanced BIOS Features.............................................................. 36
3.6 Advanced Chipset Features.......................................................... 40
3.7 Integrated Peripherals................................................................... 43
3.8 Power Management Setup............................................................ 48
3.9 Plug and Play / PCI Configurations............................................... 51
3.10 PC Health Status........................................................................... 52
3.11 Frequency/Voltage Control............................................................ 53
3.12 Load Fail-Safe Defaults................................................................. 54
3.13 Load Optimized Defaults............................................................... 54
3.14 Supervisor/User Password Setting................................................ 54
3.15 Exit Selecting ................................................................................ 55
Warranty Policy ...........................................................................57

Introduction •1
1
Introduction
The NuPRO-865 single board computer is optimized for socket 478 FC-PGA
processors, supporting an 800/533MHz Front Side Bus. The memory can
accommodate is up to 2GB DDR333/400 SDRAM. This board is based on the
Intel®865G chipset and is fully designed for harsh industrial environment. The
NuPRO-865 chipset is an on-die enhanced Intel®Extreme Graphics 2 with one
10/100/1000 Mbps Gigabit Ethernet controller. It is optimized for CTI and
high-performance applications.
I/O functions include two SATA ports, two serial ports, one parallel port, two
ATA100 IDE interface, one FDC interface, four USB 2.0 ports, Watch Dog Timer
and PS/2 Keyboard & Mouse. Key components are selected based on the
long-term availability.

2•Introduction
1.1 Unpacking Checklist
1. Take out the NuPRO-865 series unit from the carton box, check if the unit is
properly secure in the plastic bag.
2. Check the contents of the carton box:
¡Single Board Computer ¡Installation guide
¡ATA-66/100 HDD ribbon cable ¡Floppy ribbon cable
¡Print & COM1 ribbon cable ¡USB cable (1 Set)
¡S-ATA & Power cable ¡KB & MS Y type cable

Introduction •3
¡Driver CD ¡ATX control round cable
(4-pins to 4-pins)
¡KB extend to BP round cable
(5-pins to 6-pins)
3. Optional Audio Card / Cable
¡IP-ALCS20 Audio Card ¡Audio 9-pins round cable
Note: NuPRO-865 OEM versions with non-standard configurations may
vary in function or contents according to request.
CAUTION: This board must be protected from static discharge and physical
shock. Never remove any of the socketed parts except at a
static-free workstation. Use the anti-static bag shipped with the
product to handle the board. Wear a wrist strap grounded through
one of the system's ESD Ground jacks while servicing system
components.
!

4•Introduction
1.2 Features
•Intel®Pentium®4 / Celeron™processor
•Intel®865G + ICH5 AGPset
•Support 2GB DDR333/400 SDRAM (Max.) Memory
•Front Side Bus Frequency: 533 / 800 MHz
•Chipset integrated AGP8X graphic function
•Single 10/100/1000 Mbps Gigabit Ethernet using Intel®82547GI chip
•Software programmable watchdog timer
•Hardware Monitoring
•AC97 Audio pin-header (Option IP-ALCS20 audio card)
Hardware Monitoring
Hardware monitoring allows the user to monitor various aspects of their systems
operations and status. Features include the CPU temperature, voltage, and RPM of
fan.
I/O Shield Connector
The SBC is equipped with an I/O bracket. Please use the appropriate I/O shield.
Figure 1: I/O back panel layout
NuPRO-865 Series Overview
Function NuPRO-865
Chipset i865G
SCSI Function /
LCD Function /
VGA Function (i865G)
Gigabit Ethernet Function 
AC97 Audio Pin-header (Option IP-ALCS20 Audio Card)
Two EIDE Interface 
Two SATA Interface 
One Floppy Interface 
Two Serial, One Parallel 
Four USB 2.0 ports 
KB
MS

Introduction •5
1.3 System Block Diagram
P4 Socket 478-pins ClockVRM
DATACTRLADDR
GMCH (865G)
932 FC-BGA
ICH5
460 uBGA
DDR333/266 X1
CRT
SuperI/O
W83627HF
ATA100
USB
IDE Primary
IDE Secondary
USB Port 0/1
USB Port 2/3
SATAPort1
SATAPort2
FWH
Keyboard
Mouse
COM Port
LPT Port
Floppy
iTEBridge
IT8888F ISABUS
PCI BUS
PICMG SLOT
10/100/1000
Base-TX
82547GI
CSA
DDR333/266 X1
AGP 8X
SATA
Figure 2: System Block Diagram

6•Introduction
1.4 Specifications
•Processor:
•Socket 478 processors, for Intel®Pentium®4/ Celeron™processor
•Up to 3.2GHz
•Chipset:
•Intel®865G + ICH5 AGPset
•Front Side Bus:
•400 / 533 / 800 MHz
•DRAM Module:
•Two 184pins DIMM for DDR SDRAM up to 2GB (max.)
•Support DDR 266 / 333 / 400 SDRAM
•VGA Function:
•Intel®865G chipset integrated graphic function
•Gigabit Ethernet Function:
•Intel®82547GI Gigabit Ethernet controller
•For 10 / 100 / 1000 Base-TX Ethernet
•Audio Function: (Optional)
•AC97 audio interface, by option audio card --- IP-ALCS20
•Onboard 9-pins (pin-header) interface
•SATA Function:
•Two S-ATA ports, support data transfer rates up to 150MB/s
•Onboard I/O:
•On-Chip I/O integrated with K/B, Mouse, FDD, Parallel and Serial controller
•Onboard PCI / IDE:
•Intel®ICH5 South Bridge controller
•PCI rev2.2 Compliant
•ACPI Compliant Power Management
•PCI Bus IDE Port with PIO /ATA-100 x 2 (Up to 4 Devices)

Introduction •7
•Bracket I/O Connectors:
•D-Sub Serial port (COM1)
•Single RJ-45 connector
•15-pins D-Sub VGA connector
•PS/2 style Mouse or Keyboard connector
•USB 2.0 Ports:
•Four USB 2.0 ports (pin-header)
•BIOS:
•Award Plug and Play BIOS
•Extended Function:
•Hardware monitoring function
•IrDA by pin-header
•Form Factor:
•13.3” x 4.8” (338 x 122mm)
•Weight:
•0.93lb (420g) - NuPRO-865

Award BIOS Setup •9
2
Installation
2.1 System Installation
CPU Installation
Carefully follow the steps below to install the CPU:
1. Check and confirm that the jumpers are correctly set for the CPU being
installed (figure 3).
2. Lift the releasing lever of the Socket 478.
3. Align the pins of the CPU with the pinholes of the Socket 478. Be sure to pay
attention to the orientation of the CPU.
Figure 3: CPU Socket
4. Push down the CPU into the Socket 478.
5. Push down the release lever and lock it against the key hook.
6. Hook the hole in ZIF clip for the CPU cooling fan onto the notch on the socket
478.
7. Place the CPU cooling fan on top of the CPU surface.

10 •Award BIOS Setup
8. Push down the opposite side of the ZIF clip and hook it.
9. Slide the head of the clip to left and lock it.
10. Connect the cooling fan cable to the socket as shown below. Be careful not
to place the cable on the CPU cooling fan.
Removing a CPU:
1. Before removing the CPU, turn off the NuPRO-865 Series power; then wait
for about three minutes until the heat radiation plate of the cooling fan and
the CPU cools down.
2. To remove the CPU, lift the releasing lever of the Socket 478.
CAUTION: The CPU and the heat radiation plate are hot. They may cause
burns.
To remove the CPU, reverse the installation steps.
Heat Sink & Retention Module Installation
It is highly recommended that only NuPRO-865 Heat sink and fan (Figure 4),
designed for use in the chassis be used - the use of other heat sinks, including
those boxed with CPUs, may damage the NuPRO-865 SBC.
Make sure that good contact is made between the processors and the heat sinks.
Insufficient contact, incorrect types of heat sinks, fans, or thermal compound
used or improper amount of thermal compound applied on the CPU die can
cause the processors to overheat, which may crash the system.
The Retention Module is used to hold up the weight of the Heat sink and fan.

Award BIOS Setup •11
Figure 4: Heat Sink Installation
Memory Module Installation
Figure 5 illustrates the notch marks and what they should look like on the DIMM
memory module.
DIMMs have 184-pins and two notches matching the onboard DIMM socket.
DIMM modules are installed by placing the chip firmly into the socket at a
90-degree angle and pressing straight down (figure 6) until it fits tightly into the
DIMM socket.
Figure 5: DIMM Memory and 184-pins Socket
Figure 6: Memory Installation
Heat Sink & Fan
(For P4 processor only) Installation
Retention Module
(For P4 Heat Sink & Fan)

12 •Award BIOS Setup
Carefully follow the steps below to install the DIMMs:
1. To avoid generating static electricity and damaging the DIMM, ground
yourself by touching a grounded metal surface or using a ground scrap
before touching the DIMM.
2. Do not touch the connector of the DIMM. Dirt residues may cause
malfunctions.
3. Hold the DIMM with its notch to the front side of the NuPRO-865 Series and
insert it completely into the socket. A DIMM should be inserted into the inner
socket first. Guide the hole on each end of the DIMM over the retaining post
at each end of the DIMM socket.
4. If installing two DIMMs, install the second DIMM using the same procedure
as above.
5. Do not forcefully insert the DIMM if it does not go in smoothly. Remove the
DIMM completely and try again.
6. Make sure the DIMM is properly installed and locked by the tabs on both
sides of the socket.
Removing a DIMM:
To remove the DIMM, use fingers or a small screwdriver to carefully push away
the plastic tabs that secure the DIMM at each end. Lift it out of the socket.
Make sure the DIMM is stored in an anti-static bag which must be of
the same size and manufacture of memory modules.
Setting Jumpers and DIP Switches
There are jumpers and DIP-switches on the Embedded Board of the NuPRO-865
Series. The jumpers can be set for various operations.
Figure 7: Jumper Connector

Award BIOS Setup •13
For three-pin jumpers (Figure 7), the jumper setting is 1-2 when the jumper
connects pins 1 and 2. The setting is 2-3 when pins 2 and 3 are connected and so
on. The pins are numbered “1“ and “3“ on the circuit board for identification
purposes. Also, pin 1 has a thick line surrounding the jumper.
To move a jumper from one position to another, use needle-nose pliers or
tweezers to pull the pin cap off the pins and move to the required position.

14 •Award BIOS Setup
2.2 Board Layout
CN7 LPT
CN4 FLOPPY
COM2
CN10
CN11 COM1
LAN
CN14
CN17 VGA CN18 CN19
KB/MS
KB/MS
CN16 AC97
JP2
SATA2
SATA1
CN12
ATX CTL.
BATT1
JP1
CN3 CN6
IDE1IDE2
CN13
CN15
USB0/1 USB2/3
CN9
CN8
SYSTEMFAN
CPUFAN
DIMM1DIMM2
CN1
BZ1
CN2
92003
Figure 8: Jumper and Connector Locations