ADLINK Technology GIE64+ User manual

Advance Technologies; Automate the World.
Manual Rev.: 4.00
Revision Date: July 17, 2013
Part No: 50-11245-1030
GIE64+
4-CH PoE GigE Vision Interface Card
User’s Manual

ii
Revision History
Revision Release Date Description of Change(s)
2.00 Feb. 24, 2012 Initial release
2.10 Mar. 23, 2012 Minor spec changes
3.00 May 30, 2013 New product version release
4.00 July 17, 2013 Revision to new product version release

Preface iii
GIE64+
Preface
Copyright 2013 ADLINK Technology, Inc.
This document contains proprietary information protected by copy-
right. All rights are reserved. No part of this manual may be repro-
duced by any mechanical, electronic, or other means in any form
without prior written permission of the manufacturer.
Disclaimer
The information in this document is subject to change without prior
notice in order to improve reliability, design, and function and does
not represent a commitment on the part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, spe-
cial, incidental, or consequential damages arising out of the use or
inability to use the product or documentation, even if advised of
the possibility of such damages.
Environmental Responsibility
ADLINK is committed to fulfill its social responsibility to global
environmental preservation through compliance with the Euro-
pean Union's Restriction of Hazardous Substances (RoHS) direc-
tive and Waste Electrical and Electronic Equipment (WEEE)
directive. Environmental protection is a top priority for ADLINK.
We have enforced measures to ensure that our products, manu-
facturing processes, components, and raw materials have as little
impact on the environment as possible. When products are at their
end of life, our customers are encouraged to dispose of them in
accordance with the product disposal and/or recovery programs
prescribed by their nation or company.
Trademarks
Product names mentioned herein are used for identification pur-
poses only and may be trademarks and/or registered trademarks
of their respective companies.

iv Preface
Conventions
Take note of the following conventions used throughout this
manual to make sure that users perform certain tasks and
instructions properly.
NOTE:
NOTE:
Additional information, aids, and tips that help users perform
tasks.
CAUTION:
Information to prevent minor physical injury, component dam-
age, data loss, and/or program corruption when trying to com-
plete a task.
WARNING:
Information to prevent serious physical injury, component
damage, data loss, and/or program corruption when trying to
complete a specific task.

Table of Contents v
GIE64+
Table of Contents
Revision History...................................................................... ii
Preface.................................................................................... iii
List of Figures....................................................................... vii
List of Tables.......................................................................... ix
1 Introduction ........................................................................ 1
1.1 Overview.............................................................................. 1
1.2 Features............................................................................... 1
1.3 Applications ......................................................................... 2
1.4 Specifications....................................................................... 2
1.4.1 Power over Ethernet Port...........................................2
1.4.2 General Specifications................................................3
1.5 I/O and Indicators ................................................................ 4
1.5.1 RJ-45 Ethernet Port....................................................5
1.5.2 Status LEDs................................................................6
1.5.3 Power Connector........................................................7
1.5.4 Card ID Switch (S1)....................................................8
1.5.5 Onboard LED Status Indicators................................10
2 Getting Started ................................................................. 13
2.1 Unpacking Checklist.......................................................... 13
2.2 Installation.......................................................................... 13
Important Safety Instructions.............................................. 15
Getting Service...................................................................... 17

vi Table of Contents
This page intentionally left blank.

List of Figures vii
GIE64+
List of Figures
Figure 1-1: GIE64+ Schematic Diagram............................................4
Figure 1-2: GIE64+ Board Layout......................................................5
Figure 1-3: RJ-45 Ethernet Connector...............................................5
Figure 1-4: Status LEDs.....................................................................6
Figure 1-5: Power Connector.............................................................7
Figure 1-6: Card ID Switch Location..................................................8
Figure 1-7: LED Status Indicator Location.......................................10

viii List of Figures
This page intentionally left blank.

List of Tables ix
GIE64+
List of Tables
Table 1-1: Board Layout Legend ......................................................5
Table 1-2: RJ-45 Ethernet Port Connector Signals...........................6
Table 1-3: Status LED Legend .........................................................7
Table 1-4: Power Connector Pin Assignments.................................7
Table 1-5: ID Switch Position Legend...............................................9
Table 1-6: LED Status Indicator Display Definitions.......................11

xListofTables
This page intentionally left blank.

Introduction 1
GIE64+
1 Introduction
1.1 Overview
ADLINK's GIE64+ is a PCI Express®x4 lane, PoE (Power over
Ethernet) frame grabber with support for four independent Gigabit
Ethernet ports. Multiple Gigabit Ethernet Vision device connec-
tions are supported for standard Gigabit Ethernet Vision data
transfer rates of up to 1000 Mb/s.
The GIE64+ features not only PoE, combining power supply and
signal into a single cable, but also IEEE 1588 (precise time proto-
col), enabling synchronization with multi-camera acquisition.
The ADLINK GIE64+ also supports the Link aggregation control
protocol, offering inexpensive setup of a double-speed backbone
network for data transfers significantly exceeding those of a single
Gigabit Ethernet port or device.
Finally, the GIE64+ provides a SmartPoe API, allowing remote
on/off switching of PoE status via programming with no require-
ment for cable plug connection/disconnection.
1.2 Features
XIEEE802.3af (48 V, 15.4 W per channel) compliant, support-
ing classes 0,1,2,3,4
XPowered Device (PD) auto-detection and classification
XSupport for four independent GbE ports
XSupport for Link aggregation
XSupport for jumbo frames (9 kBytes)
XIEEE 1588 compliant, supporting multi-camera synchroni-
zation
XCurrent limit, and short-circuit protection
XPCI Express x4 compliant
XSoftware API for easy remote PoE switching
XPoE loading from PCIe bus requires no external power con-
nector (when total PoE loading is less than 20W)

2Introduction
1.3 Applications
The GIE64+ is ideally suited to frame grab functions in a wide vari-
ety of applications, including:
XMachine Vision Inspection systems
XScientific research instrumentation
XMedical research instrumentation
1.4 Specifications
1.4.1 Power over Ethernet Port
The GIE64+ Power over Ethernet specification supports
XFour fully-integrated Gigabit Ethernet Media Access Control
(MAC) and physical layer (PHY) ports
XFull controller compliance with IEEE 802.3.af standard for
maximum 15.4 watts, with power up to 48 V over existing
CAT-5 Ethernet infrastructure, with no modifications
required
XStandard IEEE 802.3 Ethernet interface provided for
1000BASE-T, 100BASE-TX, and 10BASE-T applications
(802.3, 802.3u, and 802.3ab)
NOTE:
NOTE:
The GIE64+ Function Library Reference can be downloaded
from the product’s pages at http://www.adlinktech.com
CAUTION:
If total POE loading exceeds 20W, Power Connector connec-
tion is required to avoid system damage. Please see
Section 1.5.3 Power Connector

Introduction 3
GIE64+
1.4.2 General Specifications
Function Description
Power Requirements
XInput voltage: 3.3VDC and 12VDC, (w/ PC
system power)
XInput from power connector (see
Figure 1-2): Max 7A @ 12VDC (support-
ing up to 4 ports at 15.4W per PoE port)
XInput from PCIe slot: Max 2.1 A @ 12VDC
(compatible to PCIe Spec), with connec-
tion cut off by fuse when exceeded
PCI Express
PCIe X4 ports 1 port PCIe X4, for GigE Vision
Differential Output Peak
to Peak Voltage +0.8 V to +1.2 V
Differential Input Peak
to Peak Voltage +0.175 V to +1.2 V
Input voltage for
PERST#, WAKE#, and
SMBus -0.75 V to +4.05 V
Gigabit Ethernet
LAN chip Intel®82574L, PCIe v1.1 (2.5GT/s)
Gigabit Ethernet Ports 4
PoE Signal
Max Output Power 15.4 W per channel, IEEE 802.3af compliant
PoE Output Voltage 44 to 48 V, PoE port positive voltage feed
Physical
Dimensions 145 W x 111.12 L mm (5.71 X 4.38 in.)
Operating Temperature 0° C to 55° C
Storage Temperature -40° C to 85° C
Safety Compliance CE/FCC Class A; RoHS

4Introduction
1.5 I/O and Indicators
Figure 1-1: GIE64+ Schematic Diagram
NOTE:
NOTE:
All dimensions shown are in mm
101.26
145

Introduction 5
GIE64+
Figure 1-2: GIE64+ Board Layout
Table 1-1: Board Layout Legend
1.5.1 RJ-45 Ethernet Port
Figure 1-3: RJ-45 Ethernet Connector
APCIelane
B RJ-45 Ethernet Ports
C PoE Status LED
D Power Connector
AA
B
C
D
1 8

6Introduction
Table 1-2: RJ-45 Ethernet Port Connector Signals
1.5.2 Status LEDs
Figure 1-4: Status LEDs
Pin Signal
1 MDI0+ (PoE_DC48V)
2 MDI0- (PoE_DC48V)
3 MDI1+ (PoE_DC0V)
4 MDI2+ (PoE_DC48V)
5 MDI2- (PoE_DC48V)
6 MDI1- (PoE_DC0V)
7 MDI3+ (PoE_DC0V)
8 MDI3- (PoE_DC0V)

Introduction 7
GIE64+
The GIE64+ provides four yellow LEDs to indicate operating con-
ditions of the four PoE ports, as shown, with corresponding status
as follows.
Table 1-3: Status LED Legend
1.5.3 Power Connector
Figure 1-5: Power Connector
Table 1-4: Power Connector Pin Assignments
LED Status
1ON: Port 1 PoE On
OFF: Port 1 PoE Off
2ON: Port 2 PoE On
OFF: Port 2 PoE Off
3ON: Port 3 PoE On
OFF: Port 3 PoE Off
4ON: Port 4 PoE On
OFF: Port 4 PoE Off
Pin Signal
1 +12V
2GND
3GND
4NC
4
3
2
1

8Introduction
1.5.4 Card ID Switch (S1)
The GIE64+ is equipped with a card ID switch allowing identifica-
tion of individual cards in a multi-card system.
Figure 1-6: Card ID Switch Location

Introduction 9
GIE64+
Table 1-5: ID Switch Position Legend
ID S1 Slider ID S1 Slider
4321 4321
0 off off off off 8 on off off off
1 off off off on 9 on off off on
2 off off on off 10 on off on off
3 off off on on 11 on off on on
4 off on off off 12 on on off off
5 off on off on 13 on on off on
6 off on on off 14 on on on off
7 off on on on 15 on on on on

10 Introduction
1.5.5 Onboard LED Status Indicators
9 LEDs on the rear side of the GIE64+ indicate the data stream for
each port, as follows.
Figure 1-7: LED Status Indicator Location
LED Status Definition
1, 2, 3, 4 OFF Abnormal, PCIe switch downstream
function is disabled.
Blinking Normal
5, 6, 7, 8 OFF Abnormal, PCIe switch downstream
function is disabled.
ON/Blinking Normal