ADLINK Technology cPCI-3610 Series User manual

Advance Technologies; Automate the World.
Manual Rev.: 2.00
Revision Date: June 2, 2010
Part No: 50-15070-1000
cPCI-3610 Series
3U CompactPCI® Dual-Core Intel® Atom™
Processor Blade
User’s Manual

Revision History
Revision Release Date Description of Change(s)
2.00 2010/06/02 Initial Release

Preface iii
cPCI-3610
Preface
Copyright 2010 ADLINK Technology Inc.
This document contains proprietary information protected by copy-
right. All rights are reserved. No part of this manual may be repro-
duced by any mechanical, electronic, or other means in any form
without prior written permission of the manufacturer.
Disclaimer
The information in this document is subject to change without prior
notice in order to improve reliability, design, and function and does
not represent a commitment on the part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, spe-
cial, incidental, or consequential damages arising out of the use or
inability to use the product or documentation, even if advised of
the possibility of such damages.
Environmental Responsibility
ADLINK is committed to fulfill its social responsibility to global
environmental preservation through compliance with the Euro-
pean Union's Restriction of Hazardous Substances (RoHS) direc-
tive and Waste Electrical and Electronic Equipment (WEEE)
directive. Environmental protection is a top priority for ADLINK.
We have enforced measures to ensure that our products, manu-
facturing processes, components, and raw materials have as little
impact on the environment as possible. When products are at their
end of life, our customers are encouraged to dispose of them in
accordance with the product disposal and/or recovery programs
prescribed by their nation or company.
Trademarks
Product names mentioned herein are used for identification pur-
poses only and may be trademarks and/or registered trademarks
of their respective companies.

iv Preface
Using this Manual
Audience and Scope
The cPCI-3610 User’s Manual is intended for hardware
technicians and systems operators with knowledge of installing,
configuring and operating CompactPCI systems.
Manual Organization
This manual is organized as follows:
Chapter 1, Introduction: Introduces the cPCI-3610, its features,
block diagrams, and package contents.
Chapter 2, Specifications: Presents detailed specification infor-
mation, power consumption, and technical drawings.
Chapter 3, Functional Description: Describes the cPCI-3610
main functions.
Chapter 4, Board Interfaces: Describes the cPCI-3610 board
interfaces.
Chapter 5, Getting Started: Describes the installation of compo-
nents to the cPCI-3610 and rear transition modules.
Chapter 6, Driver Installation: Provides information on how to
install the cPCI-3610 device drivers.
Chapter 7, Utilities: Describes the utilities of the cPCI-3610
Series.
Chapter 8, BIOS Setup: Describes basic navigation for the
AMIBIOS®8 BIOS setup utility.
Important Safety Instructions: Presents safety instructions all
users must follow for the proper setup, installation and usage of
equipment and/or software.
Getting Service: Contact information for ADLINK’s worldwide
offices.

Preface v
cPCI-3610
Conventions
Take note of the following conventions used throughout this
manual to make sure that users perform certain tasks and
instructions properly.
NOTE:
NOTE:
Additional information, aids, and tips that help users perform
tasks.
CAUTION:
Information to prevent minor physical injury, component dam-
age, data loss, and/or program corruption when trying to com-
plete a task.
WARNING:
Information to prevent serious physical injury, component
damage, data loss, and/or program corruption when trying to
complete a specific task.

vi Preface
This page intentionally left blank.

Table of Contents vii
cPCI-3610
Table of Contents
Revision History...................................................................... ii
Preface .................................................................................... iii
List of Figures ........................................................................ xi
List of Tables........................................................................ xiii
1 Introduction ........................................................................ 1
1.1 Overview.............................................................................. 1
1.2 Features............................................................................... 2
1.3 Block Diagram ..................................................................... 3
1.4 Product List.......................................................................... 4
1.5 Package Contents ............................................................... 5
2 Specifications..................................................................... 7
2.1 cPCI-3610 Specifications..................................................... 7
2.2 I/O Connectivity Table ......................................................... 9
2.3 Power Requirements......................................................... 10
3 Functional Description .................................................... 13
3.1 Processor........................................................................... 13
3.2 Chipset............................................................................... 16
3.3 Super I/O ........................................................................... 16
3.4 Battery ............................................................................... 17
3.5 PMC/XMC.......................................................................... 17
4 Board Interfaces............................................................... 19
4.1 cPCI-3610 Blade Board Layout......................................... 19
4.2 cPCI-3610 Blade Assembly Layout ................................... 20
4.3 cPCI-3610D Blade Assembly Layout................................. 21
4.4 cPCI-3610P Blade Assembly Layout................................. 22

viii Table of Contents
4.5 cPCI-3610 Series Front Panel Layout ............................... 23
4.6 cPCI-R3610T RTM Board Layout...................................... 25
4.7 cPCI-R3610(T) RTM Front Panel ...................................... 26
4.8 Connector Pin Assignments............................................... 27
4.9 Switch and Jumper Settings .............................................. 41
5 Getting Started .................................................................. 47
5.1 CPU and Heatsink ............................................................. 47
5.2 Hard Drive Installation........................................................ 48
5.3 PMC/XMC Card Installation............................................... 50
5.4 Installing the cPCI-3610 to the Chassis............................. 54
5.5 RTM Installation - cPCI-R3610(T)...................................... 55
6 Driver Installation.............................................................. 57
7 Utilities ............................................................................... 59
7.1 Watchdog Timer................................................................. 59
7.2 Preboot Execution Environment (PXE).............................. 64
8 BIOS Setup ........................................................................ 65
8.1 Starting the BIOS............................................................... 65
8.2 Main Setup......................................................................... 69
8.3 Advanced BIOS Setup....................................................... 70
8.3.1 CPU Configuration.........................................................71
8.3.2 IDE Configuration ..........................................................73
8.3.3 Super IO Configuration..................................................74
8.3.4 Hardware Health Configuration .....................................75
8.3.5 USB Configuration.........................................................76
8.3.6 AHCI Configuration........................................................78
8.3.7 Remote Access Configuration .......................................79
8.4 Advanced PCI/PnP Settings.............................................. 81
8.5 Boot Settings ..................................................................... 82
8.5.1 Boot Settings Configuration...........................................83

Table of Contents ix
cPCI-3610
8.6 Security Setup ................................................................... 84
8.7 Chipset Setup.................................................................... 87
8.8 Exit Menu........................................................................... 88
Important Safety Instructions .............................................. 91
Getting Service...................................................................... 93

xTableofContents
This page intentionally left blank.

List of Figures xi
cPCI-3610
List of Figures
Figure 1-1: cPCI-3610 Series Functional Block Diagram...................3
Figure 4-1: cPCI-3610 Blade Board Layout.....................................19
Figure 4-2: cPCI-3610 Assembly Layout .........................................20
Figure 4-3: cPCI-3610D Board Layout.............................................21
Figure 4-4: cPCI-3610, cPCI-3610D Front Panel Layout.................23
Figure 4-5: cPCI-3610P Front Panel Layout....................................24
Figure 4-6: cPCI-R3610T RTM Board Layout..................................25
Figure 4-7: cPCI-R3610(T) RTM Front Panel..................................26

xii List of Figures
This page intentionally left blank.

List of Tables xiii
cPCI-3610
List of Tables
Table 4-1: cPCI-3610 Front Panel System LED Descriptions ........24
Table 4-2: USB Connector Pin Definition........................................27
Table 4-3: VGA Connector Pin Definition .......................................27
Table 4-4: GbE Connector Pin Definitions......................................28
Table 4-5: Ethernet Status LED Definitions....................................28
Table 4-6: PS/2 Keyboard/Mouse Connector Pin Definition...........29
Table 4-7: DB-9 Serial Port Connector Pin Definition.....................29
Table 4-8: cPCI-R3610(T) Serial Port Pin Header Definition..........30
Table 4-9: Serial ATA Connector on RTM Pin Definition................30
Table 4-10: Serial ATA Connector on DB-3610L2 Pin Definition......31
Table 4-11: CompactFlash Connector Pin Definition........................32
Table 4-12: DB-3610CF Connector Pin Definition............................33
Table 4-13: DB-3610L2 Connector Pin Definition.............................34
Table 4-14: DB-3UMC Connector Pin Definition...............................35
Table 4-15: PMC Connector Pin Definitions.....................................36
Table 4-16: XMC Connector Pin Definition.......................................38
Table 4-17: CompactPCI J1 Connector Pin Definition......................39
Table 4-18: CompactPCI J2 Connector Pin Definition......................40
Table 4-19: VGA/GPIO Mode Switch Settings.................................41
Table 4-20: COM1 Mode Selection Switch Settings.........................42
Table 4-21: COM2 Mode Selection Switch Settings.........................43
Table 4-22: COM3 Mode Selection Switch Settings.........................44
Table 4-23: XMC VPWR Select Jumper Settings.............................45
Table 4-24: PMC V(I/O) Select Jumper Settings..............................45

xiv List of Tables
This page intentionally left blank.

Introduction 1
cPCI-3610
1 Introduction
1.1 Overview
The cPCI-3610 Series is a 3U CompactPCI single board computer
in single-slot (4HP), dual-slot (8HP) or triple-slot (12HP) width
form factor featuring the Intel® Atom™ N450, D410 or D510 pro-
cessor with ICH8M I/O Controller Hub. The cPCI-3610 provides
single channel DDR2-667/800 soldered onboard memory up to
2GB, integrated graphics on the CPU, IDE CompactFlash slot,
and 2.5” SATA HDD (cPCI-3610D/P) and one PMC/XMC site
(cPCI-3610P). Front panel I/O includes 2x USB, 2x GbE, VGA,
and additional 2x USB, COM, KB/MS, and line-in/out for the
8(12)HP cPCI-3610D(P) models.
The optional Rear Transition Module (RTM) provides 2x SATA,
2x GbE, 1x USB, 2x COM, and VGA ports. One PCI-Express x1
port, GPIO and SMBus signals are routed to the J2 connector. The
cPCI-3610 Series is ideally suited for transportation, factory auto-
mation, and other industrial applications.

2Introduction
1.2 Features
X3U CompactPCI blade in 4HP, 8HP or 12HP width form factor
XSupports Dual-Core or Single-Core Intel® Atom™ processor,
up to 1.66GHz
XGraphics and memory controllers integrated in processor
XICH8M I/O Hub
XSingle channel DDR2-667/800 SDRAM soldered onboard, up
to 2GB
X32bit/33MHz CompactPCI Interface based on PCI specifica-
tions
XOptional 32bit/66MHz PMC or PCI-Express x1 XMC site
XVGA port on front or switchable to RTM
XTwo PCI-Express® Gigabit Ethernet egress ports, configurable
to RTM by software
XOne IDE CompactFlash socket
XLine-in and Line-out ports on front panel
X2.5” SATA HDD onboard on 8HP/12HP blade and two 7-pin
SATA ports on RTM

Introduction 3
cPCI-3610
1.3 Block Diagram
Figure 1-1: cPCI-3610 Series Functional Block Diagram
DB-3610L2
DB-3UMC
J2
F
R
O
N
T
P
A
N
E
L
RGB
USB 1/2
DMI
COM1, KB/MS
PCIe x1
GbE 1
SATA 1
1x USB
USB 3/4
Intel® Atom™
Processor
N450
D410/D510
Line-in, Line-out
J1
Intel
82574L
PCIe x1
GbE 2
GbE 1/2
2.5” HDD
Codec
PMC
XMC
PCIe x1
PCIe x1
32b/66M
P
C
I
IT8783F LPC
Intel
82574L
COM2
,
COM3
SATA 2/3
PCI 32b/33M
PCIe x1, GPIO, SMBus
CF
IDE
BIOS
SPI
Soldered
Up to 2GB
DDR2-667
Intel®
ICH8M
RGB
COM2/3
HD
Pericom
PI7C9X110

4Introduction
1.4 Product List
Products in the cPCI-3610 Series include:
Processor Blade
XcPCI-3610: 4HP width (single-slot) 3U CompactPCI featur-
ing Atom™ N450, D410 or D510 processor; 1GB or 2GB
memory soldered onboard; CompactFlash slot; 2x USB;
2x GbE; VGA.
XcPCI-3610D: 8HP width (dual-slot) 3U CompactPCI featur-
ing Atom™ N450, D410 or D510 processor; 1GB or 2GB
memory soldered onboard; CompactFlash slot; 2x USB; 2x
GbE; VGA. The DB-3610L2 riser card onboard provides 2x
USB, COM, PS/2 KB/MS, Line-in, Line-out ports.
XcPCI-3610P: 12HP width (triple-slot) 3U CompactPCI fea-
turing Atom™ N450, D410 or D510 processor; 1GB or 2GB
memory soldered onboard; CompactFlash slot; 2x USB; 2x
GbE; VGA. The DB-3610L2 riser card onboard on the 2nd
layer provides 2x USB, COM, PS/2 KB/MS, Line-in,
Line-out ports. The DB-3UMC riser card on the 3rd layer
provides one PMC/XMC site.
Rear Transition Module
XcPCI-R3610: 8HP width, 50mm depth Rear Transition Mod-
ule with 2x COM, USB, 2x GbE, 2x SATA, VGA
XcPCI-R3610T: 8HP width, 80mm depth Rear Transition
Module with 2x COM, USB, 2x GbE, 2x SATA, VGA

Introduction 5
cPCI-3610
1.5 Package Contents
The cPCI-3610 is packaged with the following components. If any
of the items on the contents list are missing or damaged, retain the
shipping carton and packing material and contact the dealer for
inspection. Please obtain authorization before returning any prod-
uct to ADLINK. The packing contents of the cPCI-3610 Series are
non-standard configurations and may vary depending on customer
requests.
Processor Blade
XThe cPCI-3610 Series Processor Blade
ZCPU, RAM specifications will differ depending on
options selected
ZThermal module is assembled on the board
XY-cable for PS/2 combo port (8HP/12HP version only)
X2.5” HDD accessory pack (8HP/12HP version only)
XADLINK All-in-One CD
XUser’s manual
Rear Transition Module
XcPCI-R3610: 8HP width, 50mm depth Rear Transition Mod-
ule with 2x COM, USB, 2x GbE, 2x SATA, VGA
XcPCI-R3610T: 8HP width, 80mm depth Rear Transition
Module with 2x COM, USB, 2x GbE, 2x SATA, VGA
NOTE:
NOTE:
The contents of non-standard cPCI-3610 configurations may
vary depending on the customer’s requirements.
CAUTION:
This product must be protected from static discharge and phys-
ical shock. Never remove any of the components except at a
static-free workstation. Use the anti-static bag shipped with the
product when putting the board on a surface. Wear an
anti-static wrist strap properly grounded on one of the system's
ESD ground jacks when installing or servicing system compo-
nents.

6Introduction
This page intentionally left blank.