ADS idatalink COM-ALRS-VW2-ADS-ALCA-EN User manual

REVISION DATE
20220121
DOCUMENT NUMBER
TERMS OF USE: Automotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by
Certified Technicians who are employed by a registered business specialized in the installation of auto-
motive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle,
it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide
and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever,
including but not limited to any consequential damages, incidental damages, damages for loss of time,
loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or
may not have resulted from the use, misuse, improper installation or operation of its products. ADS
reserves itself the right to suspend any Weblink® account without notice and decline to offer technical
support to non-Certified Technicians, non-compliant Certified Technicians or end users.
BEFORE INSTALLATION
1- Connect module to computer
2- Login to Weblink account
3- Flash firmware to module (module is not preloaded with firmware)
4- Use accessories accordingly (accessories are sold separately)
Patent No. US 8,856,780 CA 2759622
INSTALL GUIDE
COMALRSVW2ADSALCAEN
HARDWARE
ADSALCA
ACCESSORIES
ADSUSB REQUIRED
COMPATIBLE RFKIT OPTIONAL
DRONE 2/3 OPTIONAL
FIRMWARE
COMALRSVW2ADSALCA
www.idatalink.comAutomotive Data Solutions Inc. © 2022
78804

Patent No. US 8,856,780 CA 2759622
VEHICLE LIST - 1 OF 1
MAKE MODEL YEAR INSTALL TYPE
FEATURES
SECURE TAKEOVER 3X LOCK START/STANDALONE MOD. ARM OEM ALARM DISARM OEM ALARM DOOR LOCK DOOR UNLOCK TRUNK/HATCH RELEASE DOOR STATUS OUTPUT TRUNK STATUS OUTPUT HOOD STATUS OUTPUT* AUTOLIGHT CTRL TACHOMETER OUTPUT BRAKE PEDAL STATUS OUTPUT E-BRAKE OUTPUT
AUDI
A4 Keyport with PTS AT 08-16 1 • • • • • • • • • • • • • •
A4 Keyport without PTS AT 08-16 2 • • • • • • • • • • • • • •
A4 Allroad Keyport with PTS AT 08-16 1 • • • • • • • • • • • • • •
A4 Allroad Keyport without PTS AT 08-16 2 • • • • • • • • • • • • • •
A5 Keyport with PTS AT 08-16 1 • • • • • • • • • • • • • •
A5 Keyport without PTS AT 08-16 2 • • • • • • • • • • • • • •
Q5 Keyport with PTS AT 09-17 1 • • • • • • • • • • • • • •
Q5 Keyport without PTS AT 09-17 2 • • • • • • • • • • • • • •
Q5 TDI Keyport with PTS AT 09-17 1 • • • • • • • • • • • • • •
Q5 TDI Keyport without PTS AT 09-17 2 • • • • • • • • • • • • • •
RS5 Keyport with PTS AT 08-16 1 • • • • • • • • • • • • • •
RS5 Keyport without PTS AT 08-16 2 • • • • • • • • • • • • • •
S4 Keyport with PTS AT 08-16 1 • • • • • • • • • • • • • •
S4 Keyport without PTS AT 08-16 2 • • • • • • • • • • • • • •
S5 Keyport with PTS AT 08-16 1 • • • • • • • • • • • • • •
S5 Keyport without PTS AT 08-16 2 • • • • • • • • • • • • • •
SQ5 Keyport with PTS AT 09-17 1 • • • • • • • • • • • • • •
SQ5 Keyport without PTS AT 09-17 2 • • • • • • • • • • • • • •
NOTE
I Warning:
Install type 1 supports idle mode.
Install type 2 does NOT support idle mode.
*Available only if vehicle is equipped with factory hood switch.
www.idatalink.comAutomotive Data Solutions Inc. © 2022 COMALRSVW2ADSALCAEN
PAGE 2 OF 19
• 20220121
DOC.: #78804

Patent No. US 8,856,780 CA 2759622
www.idatalink.comAutomotive Data Solutions Inc. © 2022 COMALRSVW2ADSALCAEN
PAGE 3 OF 19
• 20220121
BOX CONTENTS - 1 OF 1
2
1
3
2
1
3
3
4
2
1
7
6
9
5
4
3
2
1
10
8
4
5
2
6
7
1
3
4
5
2
6
1
3
D
C
B
A
F
E
PROGRAMMING
BUTTON
LED 1
BLACK
DATA PORT
(WEBLINK, RF, TELEMATIC)
BLUE
WHITE
WHITE
WHITE
BLACK
6 PIN WHITE CONNECTOR
7 PIN WHITE CONNECTOR
MODULE 4 PIN BLACK CONNECTOR
10 PIN BLACK CONNECTOR
DATA CABLE 1
DATA CABLE 2
3 PIN WHITE CONNECTOR
3 PIN BLUE CONNECTOR
BOX CONTENTS
WEBLINK CABLE (required accessory sold separately)
WEBLINK CABLE
COMPUTER
USB PORT
4 PIN BLACK CABLE
MODULE
DATA PORT
DOC.: #78804

Patent No. US 8,856,780 CA 2759622
www.idatalink.comAutomotive Data Solutions Inc. © 2022 COMALRSVW2ADSALCAEN
PAGE 4 OF 19
• 20220121
COMPATIBLE ACCESSORIES - 1 OF 1
5 AMPS
12V (+) RED
BLACK
RF KIT
ANTENNA
FLASH RF DECODER
BEFORE INSTALLATION
RF DECODERBLUE CABLE BLACK CABLE
BLACK
BLUE
MODULE
DATA PORT
RF KIT (accessories sold separately)
5 AMPS
MODULE
DATA PORT
DRONE
(NC)
TELEMATIC KIT (accessory sold separately)
01 RED
04 YELLOW OR BLUE
REMOVE THE WHITE WIRE FROM PIN 03 AND INSERT IT IN PIN 04 AND
REMOVE THE YELLOW OR BLUE WIRE FROM PIN 04 AND INSERT IT IN PIN 03.
02 BLACK
03 WHITE
12V (+)
DOC.: #78804

Patent No. US 8,856,780 CA 2759622
TECHNICAL NOTE - 1 OF 1
IMPORTANT
STARTER WIRE CONNECTION FOR VEHICLES WITH AUTOMATIC TRANSMISSION.
Black connector at brake switch under
the dashboard, near the brake pedal.
At the ECU under the wiper cowl, located under the hood, in
the engine compartement.
1 2 3 4
3
OR
RED/BLACK
BRAKE (+)
RED/BLACK
BRAKE (+)
STARTER (+) FROM RS
(IF PRESENT)
STARTER (+) FROM RS
www.idatalink.comAutomotive Data Solutions Inc. © 2022 COMALRSVW2ADSALCAEN
PAGE 5 OF 19
• 20220121
DOC.: #78804

Patent No. US 8,856,780 CA 2759622
TYPE 1 - WIRE CHART - 1 OF 1
MAKE MODEL YEAR WIRE DESCRIPTION CONNECTOR NAME CONNECTOR COLOR CONNECTOR TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR
AUDI
A4 Keyport with PTS AT
A4 Allroad Keyport with PTS AT
S4 Keyport with PTS AT
08-16
12V ~ ~ ~ ~ Red/Black (+) Behind fuse box ~
Brake ~ ~ 04 pin 02 Red/Black (+) At brake switch ~
CanH ~ ~ ~ ~ Orange/LtGreen (DATA) Twisted wires in door harness in driver kick panel ~
CanL ~ ~ ~ ~ Orange/Brown (DATA) Twisted wires in door harness in driver kick panel ~
Ignition ~ ~ ~ ~ Black (+) Behind fusebox ~
PTS 1 ~ ~ 04 pin 03 Blue/Yellow (-) Push-button ~
PTS 2 ~ ~ 04 pin 04 Blue/White (-) Push-button ~
Keysense ~ ~ 16 pin 05 Black/Yellow (-) Behind keyport ~
A5 Keyport with PTS AT
RS5 Keyport with PTS AT
S5 Keyport with PTS AT
08-16
12V ~ ~ ~ ~ Red/Black (+) Behind fuse box ~
Brake ~ ~ 04 pin 03 Red/Black (+) At brake switch ~
CanH ~ ~ ~ ~ Orange/LtGreen (DATA) Twisted wires in door harness in driver kick panel ~
CanL ~ ~ ~ ~ Orange/Brown (DATA) Twisted wires in door harness in driver kick panel ~
Ignition ~ ~ ~ ~ Black (+) Behind fusebox ~
PTS 1 ~ ~ 04 pin 03 Blue/Yellow (-) Push-button ~
PTS 2 ~ ~ 04 pin 04 Blue/White (-) Push-button ~
Keysense ~ ~ 16 pin 05 Black/Yellow (-) Behind keyport ~
Q5 Keyport with PTS AT
Q5 TDI Keyport with PTS AT
SQ5 Keyport with PTS AT
09-17
12V ~ ~ ~ ~ Red/Black (+) Behind fuse box ~
Brake ~ ~ 04 pin 03 Red/Black (+) At brake switch ~
CanH ~ ~ ~ ~ Orange/LtGreen (DATA) Twisted wires in door harness in driver kick panel ~
CanL ~ ~ ~ ~ Orange/Brown (DATA) Twisted wires in door harness in driver kick panel ~
Ignition ~ ~ ~ ~ Black (+) Behind fusebox ~
PTS 1 ~ ~ 04 pin 03 Blue/Yellow (-) Push-button ~
PTS 2 ~ ~ 04 pin 04 Blue/White (-) Push-button ~
Keysense ~ ~ 16 pin 05 Black/Yellow (-) Behind keyport ~
www.idatalink.comAutomotive Data Solutions Inc. © 2022 COMALRSVW2ADSALCAEN
PAGE 6 OF 19
• 20220121
DOC.: #78804

Patent No. US 8,856,780 CA 2759622
87A
30
87
85
86
1
1
M6
M1
M2
M3
M4 M5 DATA
M1
M2
M3
M4
M5
M5
M6
1
1
432 1
1
78 6 54321
16 15 14 13 12 11 10 9
7.5A
1 2 34
TYPE 1 - WIRING DIAGRAM - 1 OF 1
GRAY/YELLOW (NC)01 GRAY/YELLOW (NC)
02 GRAY/RED (NC)
GREEN/YELLOW (NC)03 GREEN/YELLOW (NC)
- PTS 2 (-) OUTPUT04 GREEN/RED - PTS 2 (-) OUTPUT
05 BLUE/YELLOW (NC)
06 BLUE/RED (NC)
PINK - IGNITION (+) INPUT
01 PINK - IGNITION (+) INPUT
PINK/BLACK (NC)
02 PINK/BLACK (NC)
03 ORANGE (NC)
PTS 1 (-) OUTPUT
05 ORANGE/BLACK - PTS 1 (-) OUTPUT
BROWN/YELLOW - CANL06 BROWN/YELLOW - CANL
03 WHITE/BLACK
01 WHITE - 12V (+) CONSTANT
BROWN/RED - CANH
07 BROWN/RED - CANH
04 ORANGE/WHITE - KEYSENSE (-) OUTPUT
02 YELLOW/RED (NC)
03 YELLOW/BLACK (NC)
01 YELLOW (NC)
02 WHITE/RED (NC)
INSTALL THE SUPPLIED HOOD SWITCH IF
THE VEHICLE IS NOT EQUIPPED WITH ONE.
HOOD SWITCH
OR
WITHOUT A
COMPATIBLE
ACCESSORY
WITH A COMPATIBLE
ACCESSORY.
IMPORTANT: SEE THE
COMPATIBLE ACCESSORIES
PAGE FOR DETAILS.
COMPATIBLE
ACCESSORY
DOOR HARNESS IN DRIVER KICK PANEL
TWISTED WIRES
03 RED/WHITE (NC)
02 BLUE/BLACK (NC)
04 BROWN (NC)
06 PURPLE/BLACK (NC)
05 PURPLE/YELLOW (NC)
WHITE
07 WHITE (NC)
08 BLACK/WHITE (NC)
10 PURPLE/WHITE (NC)
CANL
IGNITION (+)
KEYSENSE (-) - 05
BRAKE (+) - 02
CANH
01 GREEN/BLACK- HOOD STATUS (-) INPUT
DATA CABLE
02 WHITE (NC)
03 BLACK - GROUND
04 RED - 12V (+)
01 BLUE/WHITE (NC)
12V (+)
12V (+)
BRAKE SWITCH
BEHIND FUSE BOX
KEYPORT
10 LOOPS (30 AWG)
AROUND KEYPORT
1 : CONNECTOR BEHIND KEYPORT
10 LOOPS (30 AWG)
AROUND KEYFOB
TWO KEYS ARE REQUIRED FOR THIS INSTALLATION.
ONE KEY WILL REMAIN PERMANENTLY IN THE VEHICLE.
THE OTHER KEY WILL BE USED FOR THE PROGRAMMING
PROCEDURE. IT WILL THEN BE RETURNED TO THE OWNER.
REMOVE BATTERY
REMOVE BATTERY
09 GREEN (NC)
PTS SWITCH
PTS 2 (-) - 04
PTS 1 (-) - 03
www.idatalink.comAutomotive Data Solutions Inc. © 2022 COMALRSVW2ADSALCAEN
PAGE 7 OF 19
• 20220121
DOC.: #78804

Patent No. US 8,856,780 CA 2759622
TYPE 2 - WIRE CHART - 1 OF 1
MAKE MODEL YEAR WIRE DESCRIPTION CONNECTOR NAME CONNECTOR COLOR CONNECTOR TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR
AUDI
A4 Keyport without PTS AT
A4 Allroad Keyport without PTS AT
S4 Keyport without PTS AT
08-16
12V ~ ~ ~ ~ Red/Black (+) Behind fuse box ~
Brake ~ ~ 04 pin 02 Red/Black (+) At brake switch ~
CanH ~ ~ ~ ~ Orange/LtGreen (DATA) Twisted wires in door harness in driver kick panel ~
CanL ~ ~ ~ ~ Orange/Brown (DATA) Twisted wires in door harness in driver kick panel ~
Ignition ~ ~ ~ ~ Black (+) Behind fusebox ~
PTS 1 ~ ~ 16 pin 06 Black (-) Behind keyport ~
PTS 2 ~ ~ 16 pin 14 Black/Red (-) Behind keyport ~
PTS 3 ~ ~ 16 pin 13 Gray/Blue (-) Behind keyport
Keysense ~ ~ 16 pin 05 Black/Yellow (-) Behind keyport ~
A5 Keyport without PTS AT
RS5 Keyport without PTS AT
S5 Keyport without PTS AT
08-16
12V ~ ~ ~ ~ Red/Black (+) Behind fuse box ~
Brake ~ ~ 04 pin 03 Red/Black (+) At brake switch ~
CanH ~ ~ ~ ~ Orange/LtGreen (DATA) Twisted wires in door harness in driver kick panel ~
CanL ~ ~ ~ ~ Orange/Brown (DATA) Twisted wires in door harness in driver kick panel ~
Ignition ~ ~ ~ ~ Black (+) Behind fusebox ~
PTS 1 ~ ~ 16 pin 06 Black (-) Behind keyport ~
PTS 2 ~ ~ 16 pin 14 Black/Red (-) Behind keyport ~
PTS 3 ~ ~ 16 pin 13 Gray/Blue (-) Behind keyport
Keysense ~ ~ 16 pin 05 Black/Yellow (-) Behind keyport ~
Q5 Keyport without PTS AT
Q5 TDI Keyport without PTS AT
SQ5 Keyport without PTS AT
09-17
12V ~ ~ ~ ~ Red/Black (+) Behind fuse box ~
Brake ~ ~ 04 pin 03 Red/Black (+) At brake switch ~
CanH ~ ~ ~ ~ Orange/LtGreen (DATA) Twisted wires in door harness in driver kick panel ~
CanL ~ ~ ~ ~ Orange/Brown (DATA) Twisted wires in door harness in driver kick panel ~
Ignition ~ ~ ~ ~ Black (+) Behind fusebox ~
PTS 1 ~ ~ 16 pin 06 Black (-) Behind keyport ~
PTS 2 ~ ~ 16 pin 14 Black/Red (-) Behind keyport ~
PTS 3 ~ ~ 16 pin 13 Gray/Blue (-) Behind keyport
Keysense ~ ~ 16 pin 05 Black/Yellow (-) Behind keyport ~
www.idatalink.comAutomotive Data Solutions Inc. © 2022 COMALRSVW2ADSALCAEN
PAGE 8 OF 19
• 20220121
DOC.: #78804

Patent No. US 8,856,780 CA 2759622
1
1
M6
M1
M2
M3
M4 M5 DATA
M1
M2
M3
M4
M5
M5
M6
1
1
432 1
1
78 6 5 4321
16 15 14 13 12 11 10 9
87A
30
87
85
86
7.5A
INSTALL THE SUPPLIED HOOD SWITCH IF
THE VEHICLE IS NOT EQUIPPED WITH ONE.
HOOD SWITCH
OR
WITHOUT A
COMPATIBLE
ACCESSORY
WITH A COMPATIBLE
ACCESSORY.
IMPORTANT: SEE THE
COMPATIBLE ACCESSORIES
PAGE FOR DETAILS.
COMPATIBLE
ACCESSORY
DOOR HARNESS IN DRIVER KICK PANEL
TWISTED WIRES
TYPE 2 - WIRING DIAGRAM - 1 OF 1
GRAY/YELLOW (NC)01 GRAY/YELLOW (NC)
- PTS 3 (-) OUTPUT02 GRAY/RED - PTS 3 (-) OUTPUT
GREEN/YELLOW (NC)03 GREEN/YELLOW (NC)
- PTS 2 (-) OUTPUT04 GREEN/RED - PTS 2 (-) OUTPUT
05 BLUE/YELLOW (NC)
06 BLUE/RED (NC)
PINK - IGNITION (+) INPUT
01 PINK - IGNITION (+) INPUT
PINK/BLACK (NC)
02 PINK/BLACK (NC)
03 ORANGE (NC)
PTS 1 (-) OUTPUT
05 ORANGE/BLACK - PTS 1 (-) OUTPUT
BROWN/YELLOW - CANL06 BROWN/YELLOW - CANL
03 WHITE/BLACK
01 WHITE - 12V (+) CONSTANT
BROWN/RED - CANH
07 BROWN/RED - CANH
04 ORANGE/WHITE - KEYSENSE (-) OUTPUT
PTS 2 (-) - 14
PTS 3 (-) - 13
PTS 1 (-) - 06
03 RED/WHITE (NC)
02 BLUE/BLACK (NC)
04 BROWN (NC)
06 PURPLE/BLACK (NC)
05 PURPLE/YELLOW (NC)
WHITE
07 WHITE (NC)
08 BLACK/WHITE (NC)
10 PURPLE/WHITE (NC)
02 YELLOW/RED (NC)
03 YELLOW/BLACK (NC)
01 YELLOW (NC)
CANL
IGNITION (+)
KEYSENSE (-) - 05
BRAKE (+) - 02
CANH
02 WHITE/RED (NC)
01 GREEN/BLACK- HOOD STATUS (-) INPUT
DATA CABLE
02 WHITE (NC)
03 BLACK - GROUND
04 RED - 12V (+)
01 BLUE/WHITE (NC)
12V (+)
12V (+)
BRAKE SWITCH
BEHIND FUSE BOX
KEYPORT
10 LOOPS (30 AWG)
AROUND KEYPORT
1 : CONNECTOR BEHIND KEYPORT
10 LOOPS (30 AWG)
AROUND KEYFOB
TWO KEYS ARE REQUIRED FOR THIS INSTALLATION.
ONE KEY WILL REMAIN PERMANENTLY IN THE VEHICLE.
THE OTHER KEY WILL BE USED FOR THE PROGRAMMING
PROCEDURE. IT WILL THEN BE RETURNED TO THE OWNER.
REMOVE BATTERY
REMOVE BATTERY
09 GREEN (NC)
www.idatalink.comAutomotive Data Solutions Inc. © 2022 COMALRSVW2ADSALCAEN
PAGE 9 OF 19
• 20220121
DOC.: #78804

Patent No. US 8,856,780 CA 2759622
01
ENGINE
START
STOP
STOP ACC ON START
ON
02
03
ENGINE
START
STOP
STOP ACC ON START
STOP
04
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Push start button twice [2x] to ON position.
Wait, LED 1 will turn solid GREEN then will
turn OFF.
Push start button once [1x] to OFF position.
Module Programming Procedure completed.
www.idatalink.comAutomotive Data Solutions Inc. © 2022 COMALRSVW2ADSALCAEN
PAGE 10 OF 19
• 20220121
DOC.: #78804

Patent No. US 8,856,780 CA 2759622
>>
01
02
ENGINE
START
STOP
OFF ACC ON START
ON
03
04
ENGINE
START
STOP
OFF ACC ON STARTOFF
05
>>
VALET MODE PROGRAMMING PROCEDURE - 1 OF 1
NOTE: In Valet Mode, the Remote starter is not
functional. Keyless entry, Lock and Unlock will
remain functional. See RF kit user manual for
alternate valet mode programming.
Time restriction. Complete next step within 7
seconds.
Cycle ignition ON five times [5x OFF/ON]
rapidly.
Wait, LED 1 will turn solid RED for 2 seconds.
Set ignition to OFF position.
Valet Mode Programming Procedure
completed.
To exit valet mode: repeat steps 1 to 5.
www.idatalink.comAutomotive Data Solutions Inc. © 2022 COMALRSVW2ADSALCAEN
PAGE 11 OF 19
• 20220121
DOC.: #78804

Patent No. US 8,856,780 CA 2759622
>>
01
02
ENGINE
START
STOP
OFF ACC ON START
ON
03
04
05
06
07
>>
08
09
ENGINE
START
STOP
OFF ACC ON STARTOFF
10
AFTERMARKET REMOTE PROGRAMMING PROCEDURE - 1 OF 1
WARNING: Program aftermarket remotes
before usage. A maximum of four [4x]
aftermarket remotes per system.
Time restriction. Complete next step within 7
seconds.
Cycle ignition ON five times [5x OFF/ON]
rapidly.
LED 1 will turn solid RED.
Time restriction. Complete next step within 2
seconds from previous step.
Press once [1x] on LOCK button of aftermarket
remote.
LED 1 will flash GREEN once [1x].
LED 1 will turn solid RED.
To program additional remotes: repeat steps 4
to 7 using each additional remote.
Wait, LED 1 will turn OFF.
Set ignition to OFF position.
Aftermarket Remote Programming Procedure
completed.
www.idatalink.comAutomotive Data Solutions Inc. © 2022 COMALRSVW2ADSALCAEN
PAGE 12 OF 19
• 20220121
DOC.: #78804

Patent No. US 8,856,780 CA 2759622
>>
>>
>>
01
ENGINE
START
STOP
OFF ACC ON STARTOFF
02
03 [X]
04
05 [Y]
06
07 [Z]
08 [Z]
09
10
11 [Y]
12
13
14
>>
MODULE NAVIGATION PROCEDURE - 1 OF 1
It is mandatory to exit the Module Navigation
at the end of this procedure. Failure to exit the
Module Navigation will drain vehicle battery.
To exit the Module Navigation at any time:
Follow STEP 13.
Module must be programmed to the vehicle.
Use the Module Navigation Chart on the next
page.
Set ignition to OFF position.
TO ACCESS THE MENUS: Press and hold
programming button until LED 1 turns solid
GREEN.
IN THE MENUS: Press the programming
button as many times as the menu number
indicates. LED 1 will flash GREEN an equal
amount of times continuously.
TO ACCESS THE OPTIONS: Press and hold
programming button until LED 1 turns solid
RED.
IN THE OPTIONS: Press the programming
button as many times as the option number
indicates. LED 1 will flash RED an equal
amount of times continuously.
TO ACCESS THE SETTINGS: Press and hold
programming button until LED 1 turns solid
GREEN.
LED 1 will flash GREEN as many times as
the current (or default) setting number,
continuously.
IN THE SETTINGS: Press the programming
button as many times as necessary to access
your setting. LED 1 will flash GREEN an equal
amount of times continuously.
To return to the MENUS: exit the Module
Navigation and redo the Module Navigation
Procedure.
To save and return to the OPTIONS: Press and
hold programming button until LED 1 turns
solid RED.
LED 1 will flash RED as many times as the
current option number continuously.
Configure every other setting and proceed to
step 13.
MANDATORY: EXIT MODULE NAVIGATION.
Press and hold programming button for 7
seconds. LED 1 will flash RED rapidly. Release
programming button. LED 1 will turn OFF.
Module navigation completed.
Failure to exit the Module Navigation will drain
vehicle battery.
www.idatalink.comAutomotive Data Solutions Inc. © 2022 COMALRSVW2ADSALCAEN
PAGE 13 OF 19
• 20220121
DOC.: #78804

Patent No. US 8,856,780 CA 2759622
MODULE NAVIGATION CHART - 1 OF 1
MODULE NAVIGATION CHART:
NOTES
[X] MENUS [Y] OPTIONS [Z] SETTINGS
I Default settings are listed in bold.
01 CONFIGURATION
01 DISARM/UNLOCK BEFORE START 01 OFF
II Make sure the option is covered on the vehicle before
attempting to change the setting.
02 ON
02 RELOCK AFTER START 01 OFF
02 ON
03 RELOCK AFTER SHUTDOWN 01 OFF
02 ON
04 FORCE UNLOCK ALL ON FIRST PRESS 01 OFF
02 ON
05 N/A 01 N/A
06 N/A 01 N/A
07 FACTORY KEYLESS RS SEQUENCE
01 DISABLE
02 N/A
03 LOCK + UNLOCK + LOCK
04 LOCK + LOCK + LOCK
08 MODULE RUN TIME
01 03 MIN
02 05 MIN
03 10 MIN
04 15 MIN
05 25 MIN
06 30 MIN
07 35 MIN
08 15 MIN
09 WAIT TO START DELAY
01 02 SEC
02 05 SEC
03 08 SEC
04 10 SEC
05 15 SEC
06 20 SEC
07 25 SEC
08 30 SEC
10-12 N/A 01 N/A
02-07 Technical Support only 01 N/A 01 N/A
*Vehicle will shutdown when a door is opened.
www.idatalink.comAutomotive Data Solutions Inc. © 2022 COMALRSVW2ADSALCAEN
PAGE 14 OF 19
• 20220121
DOC.: #78804

Patent No. US 8,856,780 CA 2759622
REMOTE STARTER ERROR CODES - 1 OF 1
REMOTE STARTER ERROR CODES:
NOTES
[X] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC
I WARNING: The following applies only when the parking
lights are connected and supported by the system.
01 Engine running.
02 Key in ignition at ON position.
II After a remote starter failure, the parking lights will fl ash
three [3x] times, then will fl ash [X] number times to
indicate an error code. See table.
03 N/A
04 Trunk is open.
05 Foot brake is ON.
06 Hood is open.
07 N/A
08 Tach failure.
09 N/A
10 System is in Valet Mode.
REMOTE STARTER SHUTDOWN ERROR CODES:
NOTES
[Y] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC
I WARNING: The following applies only when the parking
lights are connected and supported by the system.
01 Engine tach signal is lost.
02 N/A
II If the engine shuts down after a remote starter sequence:
Press and hold the Trunk button and the Start button at the
same time for 2.5 seconds when using a 1-WAY remote.
OR
Press once [1x] on button “4” when using a 2-WAY remote.
The parking lights will flash four [4x] times, then will flash
[Y] number times to indicate an error code. See table.
03 Foot brake is ON.
04 Hood is open.
05 Engine RPM limiter is ON.
06 Glow plug timeout error.
07 Vehicle is moving (VSS).
08 Check engine warning light is ON.
09 Low fuel warning light is ON.
www.idatalink.comAutomotive Data Solutions Inc. © 2022 COMALRSVW2ADSALCAEN
PAGE 15 OF 19
• 20220121
DOC.: #78804

Patent No. US 8,856,780 CA 2759622
MODULE DIAGNOSTICS - 1 OF 1
TEST MODULE
LED 1 STATUS DIAGNOSTIC
I DURING PROGRAMMING
Flashing RED Missing/wrong information from firmware or vehicle.
Solid RED Module waiting for more vehicle information.
Flashing GREEN Additional steps required to complete module programming.
Solid GREEN then OFF Module correctly programmed.
OFF No activity or module already programmed.
II DURING REMOTE START
Flashing RED Module incorrectly programmed.
Solid RED Module incorrectly programmed.
Flashing GREEN Module correctly programmed and operational.
Solid GREEN then OFF Reset in progress.
OFF Invalid ground when running status from remote starter.
III WITH IGNITION OFF
Flashing RED Module incorrectly programmed or connected.
Solid RED Module not programmed. Waiting for more vehicle information.
Flashing GREEN False ground when running status from remote starter.
Solid GREEN then OFF Reset in progress.
OFF Module at rest and ready for a remote start sequence.
www.idatalink.comAutomotive Data Solutions Inc. © 2022 COMALRSVW2ADSALCAEN
PAGE 16 OF 19
• 20220121
DOC.: #78804

Patent No. US 8,856,780 CA 2759622
01
02
03
04
05
06
07
08
>>
MODULE RESET PROCEDURE - 1 OF 1
Disconnect all connectors from module except
the BLACK 4-PIN connector.
Disconnect the BLACK 4-PIN connector.
PRESS AND HOLD programming button while
connecting the BLACK 4-PIN connector.
Wait, LED 1 will flash RED. RELEASE
programming button.
LED 1 will turn RED for 2 seconds.
Module RESET completed.
Reconnect all connectors.
Repeat programming procedure.
Failure to follow procedure may result with a
DTC or a CHECK ENGINE error message.
www.idatalink.comAutomotive Data Solutions Inc. © 2022 COMALRSVW2ADSALCAEN
PAGE 17 OF 19
• 20220121
DOC.: #78804

Patent No. US 8,856,780 CA 2759622
>>
01
02
03
04
05
06
>>
TAKEOVER PROCEDURE - 1 OF 1
All vehicle doors must be closed and locked
prior to remote start sequence.
Time restriction. Complete steps 2 to 5 within
45 seconds.
Press unlock on OEM or aftermarket remote
or request switch.
Open driver door and enter vehicle.
Close driver door.
Press and release BRAKE pedal.
Take over procedure completed.
Failure to follow procedure will result in
vehicle engine shutdown.
www.idatalink.comAutomotive Data Solutions Inc. © 2022 COMALRSVW2ADSALCAEN
PAGE 18 OF 19
• 20220121
DOC.: #78804

Patent No. US 8,856,780 CA 2759622
INSTALLATION CHECKLIST - 1 OF 1
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3Press the LOCK button once [1x] on the aftermarket keyfob.
¨
Question 1: Do the doors lock?
YES: Go to next step.
¨
NO: Verify the remote programming, the RF connections and the wired door lock/unlock
connections as illustrated in the wiring diagram, if applicable. Repeat the test and call
technical support, if the problem persists.
4Press the UNLOCK button once [1x] on the aftermarket keyfob.
¨
Question 2: Do the doors unlock?
YES: Go to next step.
¨
NO: Verify the remote programming, the RF connections and the wired door lock/unlock
connections as illustrated in the wiring diagram, if applicable. Repeat the test and call
technical support, if the problem persists.
5Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
¨
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
¨
NO: Verify the remote programming, the RF connections and the wired trunk/hatch
connections as illustrated in the wiring diagram, if applicable. Repeat the test and call
technical support, if the problem persists.
6Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
¨
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
¨NO: Verify the remote programming and the RF connections. Repeat the test and call
technical support, if the problem persists.
7Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
¨
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
¨NO: Verify the remote programming and the RF connections. Repeat the test and call
technical support, if the problem persists.
8Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
¨
Question 6: Does the vehicle remote start?
YES: Go to next step.
¨NO: Verify the remote programming, the RF connections and check the remote start error
codes. Repeat the test and call technical support, if the problem persists.
9Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
¨
Question 7: Does the vehicle shut down?
YES: Go to next step.
¨NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle
and call technical support.
10 RAP and auto light shutdown test
¨
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after
remote start shutdown?
YES: Go to next step.
¨NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the
test and call technical support if the problem persists.
11 Open hood.
12 If not already installed, affi x the mandatory orange warning sticker under the hood and
proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
¨
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood
switch, then repeat the test.
¨NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
¨
Question 10: Does the vehicle shut down?
YES: Go to next step.
¨
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once
[1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the
wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST
www.idatalink.comAutomotive Data Solutions Inc. © 2022 COMALRSVW2ADSALCAEN
PAGE 19 OF 19
• 20220121
DOC.: #78804