BrandMotion 9002-8847 User manual

INSTALLATION INSTRUCTIONS
Jeep Wrangler Adjustable Rear Vision System for Factory Display Radios,
2007 – 2018 JK (Kit # 9002-8847)
Items Included in the Kit
Camera
Chassis Harness
Power Harness
22--pin white connector w/ video RCA (for factory
display radio)
Program Module
Zip lock bag with 15 Wire Ties & 3 Push Nuts
Camera Extension Bracket
These Instructions
Required Tools & Supplies
T15 & T20 Torx Bits
7mm & 10mm Sockets
Phillips Screwdriver
3/8” Wrench or Socket Drive
Plastic Trim Removal Tool
Soldering Iron, Solder, & Heat Shrink Tubing
(RECOMMENDED) or T-taps as an alternate
splicing method
Electrical Tape
Please read so you do not VOID the
warranty:
If the camera harness is run through the center on the camera bracket, it
will cut the camera harness. This will void the warranty on the camera.
9002-8847 Instructions 6-10-19.docx Page 1 of 7 KB

INSTALLATION INSTRUCTIONS
NOTE: We strive to provide accurate and up-to-date installation instructions. For the latest full color
instructions, as well as an installation video, please visit www.brandmotion.com
Install Camera
Step 1: Loosen lug nuts to remove spare tire.
Step 2: Slide Camera on studs placing harness end
inside of tire carrier.  Do not run harness through the
camera bracket opening .
Step 3: Adjust Camera head to fit your specific wheel.
Bracket is shipped in factory wheel configuration.
Adjustment Bracket for Camera Clearance using Phillips
Screwdriver and 3/8” Wrench or Socket Drive
Note: Short Bracket has been designed for Factory
offset wheels. Use the Long Bracket for wheels with
larger offsets.
Step 4: Remove spare tire and slide (3) supplied Push
Nuts on the studs.
9002-8847 Instructions 6-10-19.docx Page 2 of 7 KB

INSTALLATION INSTRUCTIONS
Step 5: Reinstall spare tire.
Install Chassis Harness
Step 6: Insert connector from Camera connector
through the rear gate vent behind tire carrier.
Step 7: Using a plastic trim removal tool, remove
interior panels on inside of rear gate.
Step 8: Pull harness through the rear gate openings.
Step 9: Use supplied Wire Ties to secure Chassis
Harness to existing harness.
Step 10: Use supplied Wire Ties to secure Chassis
Harness to existing harness.
9002-8847 Instructions 6-10-19.docx Page 3 of 7 KB

INSTALLATION INSTRUCTIONS
Step 11: Use supplied Wire Ties to secure Chassis
Harness to fabric factory wire cover. CAUTION: Leave
enough slack to allow gate to open fully.
Step 12: Use a T20 Torx bit to remove subwoofer box.
Step 13: Using a plastic trim removal tool, pry off rear
seat belt closeout.
Step 14: Using a plastic trim removal tool, remove rear
access panel to expose 10mm bolt, and remove bolt.
Step 15: Pull out subwoofer box slightly to gain access
to run Chassis Harness along existing harness
Step 16: Pull back carpet and continue running Chassis
Harness forward.
Step 17: Run Chassis Harness under B-pillar cover to
passenger door sill. Use a plastic trim removal tool to
remove the (2) plastic push pins and remove passenger
sill plate/kick panel.
9002-8847 Instructions 6-10-19.docx Page 4 of 7 KB

INSTALLATION INSTRUCTIONS
Step 18: Remove rubber bin insert from top of dash.
Step 19: Remove 7mm bolt .
Step 20: Using a plastic trim removal tool, remove
window switch panel.
Step 21: Disconnect harness from window switches.
Step 22: Remove 7mm bolt.
Step 23: Remove driver knee bolster cover.
9002-8847 Instructions 6-10-19.docx Page 5 of 7 KB

INSTALLATION INSTRUCTIONS
Step 24: Remove (2) 7mm bolts on both sides of the
steering column.
Step 25: Remove center stack/cluster surround.
Step 26: Remove glove box for access and run Mirror
Harness toward center of dash.
Step 27: Using a plastic trim removal tool, remove
HVAC panel.
Step 28: Connecting Power
Splice Red power wire to White/Grey reverse wire in
passenger kick panel (Engage parking brake and verify
reverse wire has 12v only when vehicle is in reverse).
Splice Black Ground to chassis ground. RECOMMENDED:
Use solder and cover with heat shrink tubing or use
T-taps as an alternate connection method.
Step 29: Plug the Chassis Harness RCA connector into
provided jumper harness.
Step 30: Insert the white 22-pin connector into the
back of radio.
9002-8847 Instructions 6-10-19.docx Page 6 of 7 KB

INSTALLATION INSTRUCTIONS
Programing Instructions
PLEASE NOTE: These modules are VIN locked for
single use.
1) Start the vehicle. Allow it to run for 20-30 seconds
before proceeding to step 2.
2) Plug module into OBDII port, located under the
dash on the driver’s side, and wait to see a
GREEN LED on the module. Programming is
completed.
3) Unplug the module from the OBDII port. DO NOT
DISCARD.
Step 31: Test the system. Start vehicle and shift into
Reverse in order to check that all connections were
made properly. If all of the connections are correct you
will see the camera image displayed on the factory
display screen. To enable or disable the camera input,
select from among rear vision options in radio settings.
Step 32: Reassemble vehicle. Follow your disassembly
steps in reverse order, taking care not to bind the
harness wiring when reinstalling trim.
NOTE: This camera has parklines or non parklines
and mirror image or non mirror image options.
Grid line options: Default setting is to display grid
lines. To remove the grid line display, connect the
two green wires near the end of the camera
harness.
Display options: (Not to be used in this application!)
Default setting is mirror image display for rearward
facing camera (rear view) installation. To change to
non mirror image for forward facing camera (front
view) connect the two white wires near the end of
the camera harness.
Green and white wires on the camera harness.
9002-8847 Instructions 6-10-19.docx Page 7 of 7 KB