ADT Garda Response PM30 User manual

QUICK CONSUMER
REFERENCE GUIDE
YOUR System: ADT Alarm Garda Response
Starting to use the PM30 Alarm Panel and Keypad
1
Setting Your System
Step 1
When leaving your home ensure that all protected doors/windows, including your
front door, are closed before setting your System.
Step 2
Set your System by:
Option 1:
The Keypad – by pressing the “set” key and presenting your KeyTag /or
entering your 4-Digit User Code.
Option 2:
The Alarm Panel – by pressing the “set” key on the Alarm Panel and entering
your 4-Digit User Code.
Step 3
You will hear a continuous beeping to remind you to leave the property via your
specied exit route. Your System will set only once the exit door is closed.
Step 4
The beeping stops and your System is now successfully set.
As a security feature, the status of your System is hidden from view
• To start using your System, push the “unset” key on your Alarm Panel and enter
your 4-Digit User Code or tap the screen on the Keypad.
• The Alarm Panel/ Keypad is now lit and you are ready to start using your System.
PM30 Control Panel KeyTag
Touchscreen Keypad

2
Unsetting Your System
Unsetting starts as soon as you open your entry door or enter a protected zone which
activates the System.
Step 1
Enter your home via your specied entry route.
Step 2
Unset your System using the Keypad by pressing the “unset” key and presenting your
KeyTag.
Step 3
You will hear a beep from the Keypad or Alarm Panel conrming that your System is
successfully unset.
In compliance with the industry regulations, your System can only be unset once
you have entered the property through the entry door and you have used either your
KeyTag, set/unset KeyTag or 4 digit PIN code.
Important: Unsetting the alarm stops the Internal Siren ringing should the alarm be
activated but will not interrupt the transmission of the alarm signal to the ADT Alarm
Monitoring Centre.
Part-setting Your System
Part-setting allows you to protect part/s of your property when you are at home. For
example, protecting the downstairs area whilst you are sleeping upstairs. The part-
set option can be programmed to your System during your System installation or a
service visit.
Step 1
Part-set your System by:
Option 1:
The Keypad – by pressing the “part-set” key and presenting your KeyTag /or entering
your 4-Digit
User Code.
Option 2:
The Alarm Panel – by pressing the “part-set” key and entering your 4-Digit User code.
Step 2
Your System is now part-set.

3
Resetting/ Silencing Your System After An Alarm
To stop the alarm sounding by:
Option 1:
The Keypad – by pressing the “part-set” key and presenting your KeyTag /or entering
your 4-Digit User Code.
Option 2:
The Alarm Panel – by pressing the “part-set” key and entering your 4-Digit User code.
Important: Resetting/Silencing your System stops the Internal Siren ringing but will
not interrupt the transmission of the alarm signal to the ADT Alarm Monitoring Centre.
Our monitoring specialists may contact you at this point and you will be requested
to conrm your Verication Code /Password to cancel the alarm alert. Your System
might require a remote reset.
Changing/Deleting Master And User Codes
Using the Alarm Panel only
1. If ADT Screen Saver is displayed press the ‘Open Padlock key followed by the
manager code
2. The screen will now display ‘Ready’
3. Press the ‘Forwards Button’ until the display shows ‘User Settings’. Press ‘OK’
button
4. The display will now show ‘Set Zone Bypass’
5. Press ‘Forward Button’ until ‘User Codes’ is displayed and press ‘OK’
6. Display will now show ‘User 01 Code’ and a black box will be showing.
7. Using the ‘Forward Button’ press until you get to the code you want to change or
add. Once there press the ‘OK’ button
8. The display will show the code already installed or the display will be blank.
To delete a user code
9a. To erase the code enter ‘0000’ and press ‘OK’ button, you will hear a ‘Happy
Beep’ and the display will show the user number but no code will be shown. Move
to step 10
To enter a new user code
9b. Overtype the existing code with the new code and this should be displayed for
you. If correct then press the ‘OK’ button. You will hear a ‘Happy Beep’ and the
display will now show the user number followed by a black box. Move to step 10
10. To escape from the user setting and go back to ADT/Ready press the ‘Closed
Padlock’ button
11. The display will show ‘OK to Exit’ at this point press the ‘OK’ button

4
Panic Alarm
The Panic Alarm allows you to send an alert to the ADT Alarm Monitoring Centre if
you feel threatened or vulnerable in your home.
Step 1:
Activate the Panic Alarm using the Alarm Panel by pressing and holding and
keys simultaneously for 2 seconds.
Step 2:
The Internal Siren is activated and now sounds (unless a silent mode has been
requested at the point of installation).
Step 3:
The System sends an alert signal to the ADT Alarm Monitoring Centre, our monitoring
specialists act fast to respond to your emergency and if necessary contact the
Gardai.*
(*ADT can only contact the Gardai if your Panic Alarm has been issued with a Unique Reference Number –
URN.
Adding KeyTags
Step 1
On the Main Panel press Open Padlock and enter your master code to exit
screen saver
Step 2
Press
Step 3
The display will show: ‘User Settings’
Step 4
Press OK
Step 5
Type in your master code
Step 6
The display will show: ‘Set Zone Bypass’
Step 7
Press until you nd ‘Proximity Tags’,
Step 8
Press OK
Step 9
The display will show: ‘Add New Tag’
Step 10
Press OK

5
Adding Keytags Continued
Step 11
The display will Show: ‘ENROLL NOW or ENTR ID:XXX-XXXX’
Step 12
Go to Remote Keypad with New Tag
Step 13
Press the Open padlock followed by the master code/existing programmed
proximity tag
Step 14
Press Full Set key locked padlock Button:
Step 15
Hold the tag to the top left of the Remote Keypad to the key fob icon
Step 16
The display will show: ‘DEVICE ENROLLED’
Step 17
The display will then show:’T01:Tag (Prox)’
Step 18
Press OK
Step 19
The display will show: ‘Add New Tag’
Step 20
You can add further tags by repeating process from Step 9
Step 21
To exit press the Full Set key (locked padlock) and press OK

6
Deleting KeyTags
Step 1
On the Main Panel press Open Padlock and enter your master code to exit
the screen saver
Step 2
Press
Step 3
The display will show: ‘User Settings’
Step 4
Press OK
Step 5
Type in your master code
Step 6
The display will show: ‘Set Zone Bypass’
Step 7
Press until you nd ‘DELETE TAG
Step 8
Press OK
Step 9
The display will show the rst tag e.g. ‘T01:Tag (Prox)’
Step 10
To nd the required tag press to scroll forward
Step 11
Press Back to scroll back
Step 12
Once required tag is found press OK
Step 13
The display will show ‘<OFF> to delete’
Step 14
Press the Unset Button (unlocked padlock)
Step 15
The tag is now deleted
Step 16
You can delete more tags by repeating process from Step 7
Step 17
To exit press the Full Set key (locked padlock) and press OK

7
Adding Code
Step 1
On the Main Panel press Open Padlock and enter your master code to exit
the screen saver
Step 2
Press
Step 3
The display will show: ‘User Settings’
Step 4
Press OK
Step 5
Type in your Code
Step 6
The display will show: ‘Set Zone Bypass’
Step 7
Press Next until you nd ‘User Codes’
Step 8
Press OK
Step 9
The display will show the ‘User 01 Code █‘,
Step 10
Press (Next) until you nd a user slot without a square (i.e. ‘User 02
Code‘)
Step 11
Press OK
Step 12
The display will show: ‘User ## : 0000’,
Step 13
Type in a new code and press OK
Step 14
The display will show: ‘User 02 Code █‘,
Step 15
You can add further codes by repeating process from Step 10.
Step 16
To exit press the (locked padlock) and press OK

8
Deleting Code
Step 1
On the Main Panel press Open Padlock and enter your master code to exit
the screen saver
Step 2
Press Next
Step 3
The display will show: ‘User Settings’
Step 4
Press OK
Step 5
Type in your Code
Step 6
The display will show: ‘Set Zone Bypass’
Step 7
Press Next until you nd ‘User Codes’
Step 8
Press OK
Step 9
The display will show the ‘User 01 Code █‘,
Step 10
Press (Next) until you nd a user slot you want to delete (i.e. ‘User 02
Code █‘),
Step 11
Press OK
Step 12
The display will show: ‘User ## : ####’ (current code),
Step 13
Type in 0000 and press OK
Step 14
The display will show: ‘User 02 Code █‘,
Step 15
The code has now been deleted.
Step 16
You can delete more codes by repeating process from Step 10.
Step 17
To exit press the (locked padlock) and press OK

9
Changing Code
Step 1
On the Main Panel press Open Padlock and enter your master code to exit
the screen saver
Step 2
Press Next
Step 3
The display will show: ‘User Settings’
Step 4
Press OK
Step 5
Type in your Code
Step 6
The display will show: ‘Set Zone Bypass’
Step 7
Press Next until you nd ‘User Codes’
Step 8
Press OK
Step 9
The display will show the ‘User 01 Code █‘,
Step 10
Press (Next) until you nd a user slot you want to change
Step 11
Press OK
Step 12
The display will show: ‘User ## : ####’ (current code)
Step 13
Type in your new code and press OK
Step 14
The display will show: ‘User 01 Code █‘,
Step 15
Your code has now been changed
Step 16
You can change more codes by repeating process from Step 10.
Step 17
To exit press the (locked padlock) and press OK

10
Bypass Zone
This function allows a user to temporarily disable a device/zone from the System
(for example, to disable a movement detector when a dog is left in the house). Zone
bypass last for a one set period only and automatically switches off when the System
in Unlocked.
Step 1
Close all doors (including your entry/exit door),
Press (Unlock)
Step 2
If the panel shows ‘Enter Code’ type in CODE.
If the panel shows ‘Ready’ go to step 4.
Step 4
Press (Next)
Step 5
The display will show: ‘User Settings’
Step 6
Press (OK)
Step 7
Type in your CODE
Step 8
The display will show: ‘Set Zone Bypass’
Step 9
Press (OK)
Step 10
The panel will show the rst zone (i.e. Front door)
Step 11
If this zone is not the one you wish to bypass, press (Next) until the desired
zone is displayed

11
Bypass Zone Continued
Step 12
Press (OK)
Step 13
The Display will Show:’<OK> To Bypass’
Step 14
Press OK
Step 15
The zone is now bypassed
Step 16
You can Bypass more zones by repeating process from Step 10
Step 17
To exit press the (Lock) and press (OK)
Review Bypass
This function allows a user to see all devices/zones that are currently disabled.
Step 1
Close all doors (including your entry/exit door),
Press (Unlock)
Step 2
If the panel shows ‘Enter Code’ type in CODE.
If the panel shows ‘Ready’ go to step 4.
Step 3
Press (Next)
Step 4
The display will show: ‘User Settings’
Step 5
Press (OK)

Review Bypass Continued
Step 6
Type in your CODE
Step 7
The display will show: ‘Set Zone Bypass’
Step 8
Press the (Next)
Step 9
Until the display shows: ’Review Bypass’
Step 10
Press (OK)
Step 11
The display will show: ’Bypass List’
Step 12
Press (OK)
Step 13
The System will display the rst bypassed zone
Step 14
Press (Next) to view other bypassed zones
Step 15
To exit press the (Lock) and press (OK)
12

Recall Bypass
This Function to Removes (Recalls) the most recent Bypassed devices/zones.
Step 1
Close all doors (including your entry/exit door),
Press (Unlock)
Step 2
If the panel shows ‘Enter Code’ type in CODE
If the panel shows ‘Ready’ go to step 4.
Step 4
Press (Next)
Step 5
The display will show: ‘User Settings’
Step 6
Press (OK)
Step 7
Type in your CODE
Step 8
The display will show: ‘Set Zone Bypass’
Step 9
Press the (Next) until the display shows: ’Recall Bypass’
Step 10
The display will show: ‘<OK> to Recall’
Step 11
Press (OK)
Step 12
The display will show: ’Recall Bypass’
Step 13
To exit press the (Lock) and press (OK)
13

Time Format
Step 1
On the Main Panel press Open Padlock and enter your master code to exit
the screen saver
Step 2
Press Next
Step 3
The display will show: ‘User Settings’
Step 4
Press OK
Step 5
Type in your Code
Step 6
The display will show: ‘Set Zone Bypass’
Step 7
Press Next until you nd ‘Time & Format’
Step 8
Press OK
Step 9
The display will show the ‘EU Format-24H █‘,
Step 10
Press (Next) to select desired format
Step 11
Press OK
Step 12
To exit press the (locked padlock) and press OK
14

Time
Step 1
On the Main Panel press Open Padlock and enter your master code to exit
the screen saver
Step 2
Press Next
Step 3
The display will show: ‘User Settings’
Step 4
Press OK
Step 5
Type in your Master code
Step 6
The display will show: ‘Set Zone Bypass’
Step 7
Press Next until you nd ‘Time & Format’
Step 8
Press OK
Step 9
The display will show the ‘EU Format-24H █‘,
Step 10
Press OK
Step 11
Type in the current time in 24hour format (e.g. 1pm type in 1300)
Step 12
Press OK
Step 13
To exit press the (locked padlock) and press OK
15

Date
Step 1
On the Main Panel press Open Padlock and enter your master code to exit
the screen saver
Step 2
Press Next
Step 3
The display will show: ‘User Settings’
Step 4
Press OK
Step 5
Type in your Master code
Step 6
The display will show: ‘Set Zone Bypass’
Step 7
Press Next until you nd ‘Date & Format’
Step 8
Press OK
Step 9
The display will show the ‘Date DD/MM/YYYY █‘,
Step 10
Press OK
Step 11
Type in the current date (e.g. 13th December 2012 type in 13 12 12)
Step 12
Press OK
Step 13
To exit press the (locked padlock) and press OK
16

Preventing False Alarms
•Ensure doors and windows are securely fastened when setting the Alarm.
• Avoid placing decorations or moving objects in front of the Movement Detectors.
• Ensure that everyone using the System is fully trained and familiar with the System.
• Know the specied entry/exit route and keep to it when setting and unsetting the
System.
Useful Phone Numbers
Customer Service Centre
Call 01–6205990* to request
a routine inspection, report
a fault, request a remote
reset or if you have a query
with the monitoring of your
System.
Customer Sales Centre
Call 1850 270 270 to
upgrade your System or
Service Plan.
Moving Home?
Call 01-6205862 to let us
know you are moving and
for details of our moving
offers.
* Calls charged at the standard rate of a regular local or national landline number.
Costs from mobiles may vary.
ADT804IE PM30-PDF / Issue 1 / October 17