ADT Galaxy 8 User manual

Galaxy
8/18/60/500/512
User Guide
9
#
3
6
8
0
2
5
7
1
4
A
ent
esc
B
Galaxy 512 V1.15
11:42 TUE 11 OCT
Technical Manuals Online! - http://www.tech-man.com

Technical Manuals Online! - http://www.tech-man.com

Galaxy 8/18/60/500/512 iii User Guide
TABLE OF CONTENTS
Introduction------------------------------------------------------------------- V
KeypadInformation----------------------------------------------------------1
Setting the System ----------------------------------------------------------3
Before Setting ------------------------------------------------------------3
Setting Groups -----------------------------------------------------------3
Galaxy 500 and 512 ------------------------------------------------3
Sounder--------------------------------------------------------------------4
Part Setting -------------------------------------------------------------------4
Cancelling Setting -----------------------------------------------------------4
Group Name ------------------------------------------------------------------4
Unsetting the System-------------------------------------------------------5
Normal Entry -------------------------------------------------------------5
Straying from the Entry Route--------------------------------------------5
Slow Entry ---------------------------------------------------------------------5
Cancelling Alarms -----------------------------------------------------------5
Manager Reset-----------------------------------------------------------5
Engineer Reset-----------------------------------------------------------5
Menu Options-----------------------------------------------------------------6
Accessing the Menu ----------------------------------------------------6
Full Menu------------------------------------------------------------------6
Quick Menu ---------------------------------------------------------------6
Quick Menu Options Table ------------------------------------------------7
Omit Zones--------------------------------------------------------------------8
Omitting Zones ----------------------------------------------------------8
Setting With Omitted Zones ------------------------------------------8
Vibration Zones ----------------------------------------------------------9
ATM Zones----------------------------------------------------------------9
Forced Set---------------------------------------------------------------------9
Selecting Forces Set----------------------------------------------------9
Non-omittable Zones ---------------------------------------------------9
Chime ------------------------------------------------------------------------ 10
Display Zones -------------------------------------------------------------- 10
Selecting Display Zones --------------------------------------------- 10
Display Log------------------------------------------------------------------ 11
Print ------------------------------------------------------------------------- 12
Codes -------------------------------------------------------------------- 12
Zones--------------------------------------------------------------------- 12
Technical Manuals Online! - http://www.tech-man.com

User Guide iv Galaxy 8/18/50/500/512
Log ----------------------------------------------------------------------- 12
All ------------------------------------------------------------------------- 12
Walk Test -------------------------------------------------------------------- 13
All Zones ---------------------------------------------------------------- 13
Selected Zones -------------------------------------------------------- 13
Time and Date-------------------------------------------------------------- 14
Changing Time--------------------------------------------------------- 14
Changing Date --------------------------------------------------------- 14
Advance and Retard-------------------------------------------------- 14
Codes(General) ------------------------------------------------------------ 14
User Codes ----------------------------------------------------------------- 15
Modify PIN--------------------------------------------------------------- 16
Dual Codes ------------------------------------------------------------- 16
Modify Level ------------------------------------------------------------ 17
Duress Code------------------------------------------------------------ 17
Modify Name ----------------------------------------------------------- 18
Time Zone--------------------------------------------------------------- 18
Temporary Codes ----------------------------------------------------- 19
PIN Change Codes --------------------------------------------------- 19
Modify Groups --------------------------------------------------------- 20
Group Choice----------------------------------------------------------- 21
MAX Number ----------------------------------------------------------- 21
MAX Function ---------------------------------------------------------- 22
MAX Keypad------------------------------------------------------------ 22
PIN Warning ---------------------------------------------------------------- 23
MAX User-------------------------------------------------------------------- 23
MAX Number ----------------------------------------------------------- 23
Groups ------------------------------------------------------------------- 24
Summer---------------------------------------------------------------------- 24
Avoiding False Alarms---------------------------------------------------- 25
Zone Reference Table ---------------------------------------------------- 26
Alarm Help Messages ---------------------------------------------------- 27
Technical Manuals Online! - http://www.tech-man.com

Galaxy 8/18/60/500/512 v User Guide
INTRODUCTION
Your Galaxy alarm system is, in fact, a computer which has been
designed using the latest software and hardware technology.
First and foremost, the Galaxy meets all your security needs. The
engineer will program and commission the system to your own exacting
requirements.
Technical Manuals Online! - http://www.tech-man.com

Galaxy 8/18/60/500/512 1 User Guide
Keypad Information
General
The Galaxy Alarm system is controlled by the Galaxy Mk3 Liquid Crystal Display (LCD)
keypads. There can be a maximum of 16 keypads attached to the Galaxy 8, 18 and 60 and a
maximum of 32 keypads attached to the Galaxy 500 and 512 control panels.
NUMBER KEYS (0 – 9)
These keys are used to enter the code and to select and modify options.
Before carrying out operations on the system, users must identify themselves with a Personal
Identification Number (PIN). This number is a 4, 5 or 6 digit number selected from keys 0 - 9.
The number keys are also used where groups are programmed on the system permitting
groups (areas) to be set or unset.
VIEW KEYS (A and B)
These keys have been programmed to activate one of the system options. Pressing the A > key
after a valid code has been entered starts the full set routine. Pressing the < B key after a valid
code has been entered starts the part set routine.
Once a system option has been selected, the A > or < B keys can be used to operate as view
keys, stepping forwards (A >) or backwards (< B) through lists of information. Holding down
a view key while viewing an option list, rapidly displays each item in the list, permitting quick
access to the information.
9
#
3
6
8
0
2
5
7
1
4
A
ent
esc
B
Star key
Power
LED
LCD
display
Number keys
View keys
Enter key
Escape key
Hash key
Technical Manuals Online! - http://www.tech-man.com

User Guide 2 Galaxy 8/18/60/500/512
ENTER KEY (ent)
User level 3 and above to enter codes, data or selections into the system.
User level 2 to set and unset the system.
User level 1 to set the system.
User level 0 to log PIN entries.
ESCAPE KEY (esc)
The esc key aborts the current option to return to the previous option level. Any option
modification made prior to the option being aborted is erased. Successive pressing of the esc
key returns the user to the start display (known as the BANNER).
The esc key also aborts the setting routine if pressed during the exit time.
HASH KEY (#)
The #key is used to display additional choices for certain options, e.g. ADVANCE/RETARD
the time in the TIME/DATE option.
This key is also used as the user duress key (by pressing twice following a valid code
entry).
STAR KEY (TT
TT
T)
The Tkey is used to provide additional features for certain options, e.g. printing the event log
or deleting entries.
POWER LED
The green power LED remains lit whenever the keypad is connected to a mains power supply.
A mains power failure is indicated by the LED flashing slowly. The LED flashes rapidly if the
battery voltage falls below the minimum threshold or if one of the fuses on the control panel
PCB blows.
BANNER
The banner is the display shown on the keypad, e.g. Galaxy 500 V1.15 (with the time and
date on the bottom line). This is shown at all times, unless the menu is being accessed or an
alarm or help message is on display. The banner can be changed by the engineer.
USER CODES
The user code is a unique four, five or six digit PIN (Personal Identification Number). The
PIN identifies the user to the Galaxy Alarm panel and allows operation of the system.
Technical Manuals Online! - http://www.tech-man.com

Galaxy 8/18/60/500/512 3 User Guide
SETTING THE SYSTEM
BEFORE SETTING
Before setting the system ensure all doors and windows are secured
and areas protected by movement detectors are free from obstruction.
ENTERING A PIN - USER LEVEL 1-2
As each digit is entered the keypad responds with a bleep and
displays a T. When all the digits are entered, press the ent key to
start the setting routine.
ENTERING A PIN - USER LEVEL 3 - 6
As each digit is entered the keypad responds with a bleep and
displays a T. When all the digits are entered press the A > key to
start the setting routine.
SETTING GROUPS
Where group choice has been assigned to the PIN, select which
groups have to set as part of the setting routine. Entry of the PIN
followed by the A> key, displays the set status of each group on the
keypad screen .
Select which groups have to be to set by entering the number of the
group. For example, to set groups 2 and 3 press keys 2and 3. The
display changes to indicate the groups selected for setting. Pressing
the ent key starts the setting routine for the specified groups.
Galaxy 500 and 512
The Galaxy 500 has 16 groups whilst the 512 has 32 groups. If the
user has group choice, the available groups will be displayed at the
keypad following a valid code + A >. The groups will be displayed
showing A1 to A8. Use both A > and < B keys to scroll to the
various sets of groups.
EXIT TIME
If all the system zones are closed when the setting routine is started,
the display indicates the remaining time, in seconds, to vacate the
premises. Exit the building using the agreed route.
TIMED SET 120
Code + ent
SET A12345678
Groups UUU-----
SET A12345678
Groups SUU-----
TIMED SET 120
Code + A
1
ent
SET A12345678
Groups USS-----
SET B12345678
Groups USS-----
TIMED SET 60
Code + A
A Key
ent
Technical Manuals Online! - http://www.tech-man.com

User Guide 4 Galaxy 8/18/60/500/512
SOUNDER
During the setting period the sounder emits a continuous tone if all of
the zones are closed. If a zone is opened during the setting period, the
sounder begins to pulse. The sounder also pulses during the last 25%
of the setting time to indicate time running short.
ZONES OPEN
The exit time will reset should any zones be open or opened during
setting. The display will indicate the number of zones open and invite
viewing. Closing the zones will restart the exit time.
FINAL DOOR/TERMINATOR
The setting procedure can be manually completed by either closing
the FINAL door or by pressing the TERMINATOR button.
SYSTEM SET
When time has expired or a manual termination is made, the system
waits four seconds before setting. The sounders emit two long tones
to confirm that the system is set. The keypad briefly displays the
message SYSTEM SET, before becoming blank.
PART SETTING
To set part of the system press the < B key after the PIN. Only the
zones which have the PART attribute enabled are set. All other
setting features are the same.
CANCELLING THE SETTING
The setting routine can be aborted by pressing the esc key before the
system sets.
GROUP NAME
Press Tand #keys simultaneously when groups are displayed on the
keypad (when setting for example), will display the name of the
group . The group name should be programmed by the installation
engineer. Press the Tand #keys to return to the group display.
3 zones open
[<] [>] to view
PART SET 120
PIN+B
SET A12345678
Groups UUUUUUUU
A1 OFFICE AREA U
[<] [>] #=CHANGE
1
Technical Manuals Online! - http://www.tech-man.com

Galaxy 8/18/60/500/512 5 User Guide
UNSETTING THE SYSTEM
NORMAL ENTRY
Unsetting starts immediately when the FINAL door is opened or an
ENTRY zone is activated. The sounder pulses slowly and the user
must go directly to the keypad and enter a valid PIN, followed by
A>,<Bor ent. Users with group options, will access the UNSET
screen following PIN entry. This permits the user to unset specific
groups. To return to the SET screen press ent.
STRAYING FROM THE ENTRY ROUTE
Go directly to the keypad when entering the building. If the user
strays into a protected area and activates a zone, then a full alarm will
occur. The police may be called out and the system will have to be
reset.
SLOW ENTRY
Enter a valid PIN before the entry time expires. If the entry time
expires before a valid PIN is entered, then a full alarm will occur.
The sounder begins to pulse quickly when 75% of the entry time has
elapsed indicating time is running short.
CANCELLING ALARMS
To cancel an alarm, enter a valid PIN followed by ent at the keypad.
The keypad displays the details of the zone activated. When more
than one zone is activated, their details can be viewed using A> or
<B. Press ent to return to the banner. Certain types of alarms, once
cancelled, require a code with the appropriate reset authorisation to
be entered. The system prompts for a valid reset code by displaying
MANAGER RESET REQUIRED or ENGINEER RESET
REQUIRED on the keypad.
MANAGER RESET
Entering a manager level PIN followed by ent, resets the system
following an alarm activation.
ENGINEER RESET
Certain types of alarm require an engineer to visit the site and, after
investigation, reset the system. In such cases, the system cannot be
reset until the engineer reset has been carried out.
Galaxy 500 V1.15
15.49 MON 18 Nov
PIN + ent
4 ALARMS
[<] [>] to View
PIN + ent
CALL MANAGER
RESET REQUIRED
CALL ENGINEER
RESET REQUIRED
Technical Manuals Online! - http://www.tech-man.com

User Guide 6 Galaxy 8/18/60/500/512
MENU OPTIONS
There are two menu structures on the Galaxy control panels:
Full Menu
Only accessed by default by the Manager code on the Galaxy 60, 500
and 512 control panels.
Quick Menu
A selection of options from the full menu. The quick menu is the
default menu access for all user codes (level three and above) as well
as the Manager code on the Galaxy 8 and 18 control panels.
ACCESSING THE MENU
To access the menu enter a valid code and press the ent key. The Full
Menu or Quick Menu is accessed, depending on the user level.
OMIT ZONES is the first menu option to be displayed.
NOTE: 1. If the user does not have group choice, all groups
assigned to the user code must be unset.
2. If the user has group choice, at least one group on the
system must be unset.
3. If there are no groups, then the system must be unset.
FULL MENU
The Full Menu has a hierarchy of four structures contained within it.
Each structure is accessible by a increased user code level.
QUICK MENU
The Quick Menu offers users level three and above a selection of up
to 10 options, numbered 0 – 9. The required option is selected by
entering the option number (0 – 9) or by using the A> or <B keys to
display each option.
The menu options (as with all Galaxy lists) are circular, therefore
menu option 9 is followed by menu option 0.
The following Quick Menu options are the factory default settings.
Each option is described in the following pages.
0 = OMIT ZONES
[ent] to select
PIN + ent
Technical Manuals Online! - http://www.tech-man.com

Galaxy 8/18/60/500/512 7 User Guide
QUICK MENU OPTIONS
noitpOuneM kciuQ
.oNuneM
lluF
.oNuneM
resU
leveL
senoZtimO0113
teSdecroF1413
emihC2124
senoZyalpsiD3124
goLyalpsiD4224
tnirP5424
tseTklaW6135
etaD/emiT7146
sedoC8246
remmuS9346
teSdemiT213
teStraP313
teStnatsnI613
traPtnatsnI713
teSemoH813
teSllA913
metsyS324
srooDsseccA524
stuptuOtseT235
ecarT446
lortnoCremiT546
timOpuorG646
sseccAetomeR746
sseccAreenignE846
kcoletaD946
Table 1. Menu Options
Technical Manuals Online! - http://www.tech-man.com

User Guide 8 Galaxy 8/18/60/500/512
OMIT ZONES (User Level 3 and above)
PURPOSE
This option allows the user to omit zones before setting the system.
Zones must be eligible for omission otherwise they will not be
displayed.
NOTE: Zones remain omitted for one set period only.
SELECTING OMIT ZONES
Enter the QUICK MENU. The 0=OMIT ZONES option is displayed.
Press the ent key to select this option.
VIEWING ELIGIBLE ZONES
When the OMIT ZONES option is selected the first zone eligible for
omission is displayed. The eligible zones can be viewed by pressing
the A> or <B keys. The zones eligible for omission can be rapidly
viewed by holding down either of these keys.
OMITTING ZONES
Once the zone to be omitted is shown on the display, press the #key.
The display indicates that the zone is omitted. A> and <B keys can
then be used to select other zones to be omitted using the same
method.
NOTE: A zone is omitted from the system as soon as the # key is
pressed. The system does not have to be set for this to
come into effect.
SETTING WITH OMITTED ZONES
When the list of omitted zones is complete the setting routine is
started by pressing the ent key. The system starts to set and the
display indicates how many zones have been omitted. Alternatively
the esc key can be used to return to the menu options. Zones that
have been omitted remain omitted even after using the esc key.
NOTE: All zones omitted are recorded in the log against the user.
GALAXY 512
The Galaxy 512 will allow a single eligible zone to be omitted from
the system. Once a zone has been omitted, it is not possible to view
other zones with the omit attribute enabled, until the omitted zone is
reinstated (either automatically or manually).
ZONES OMITTED
14:35 TUE 17 DEC
1 OMITTED 120
ent
#
ent
1004 SECURITY
OMITTED ENT=SET
0 = OMIT ZONES
[ent] to select
PIN + ent
1003 INTRUDER
#=OMIT ENT=SET
ent
1004 SECURITY
#=OMIT ENT=SET
>A
Technical Manuals Online! - http://www.tech-man.com

Galaxy 8/18/60/500/512 9 User Guide
VIBRATION ZONES
If the omitted zone is a vibration zone, then all zones of this type (in
all groups) will be block omitted. The vibration zones remain omitted
until manually reinstated. Unsetting the system does not reinstate
vibration detectors.
ATM 1/2/3/4 ZONES
ATM zones are omitted by entering one of the ten ATM codes (user
188 to user 197). To select this option enter an ATM code followed
by the ent key. Use the A> key to scroll through the four ATM zone
options (ATM1 to ATM4) and select by pressing the ent key. A
predetermined ATM delay time will expire before omitting all ATM
zones with the selected ATM zone type. The zones will be omitted
for the duration of the ATM time-out period and the remaining time
in minutes will be displayed on the initiating keypad. A warning is
given ten and five minutes before the zones are reinstated. The ATM
Time-out period can be extended by entering an ATM code and
selecting 1=Reset Access. To manually reinstate ATM zones, enter
an ATM code and select 2=Abort Access.
FORCED SET (User Level 3 and above)
PURPOSE
The FORCED SET option allows the user to automatically omit
zones, eligible for omission, which are open when the system setting
routine is started. Zones omitted in this way remain omitted for one
set period only. This option is not available on the Galaxy 512.
SELECTING FORCED SET
Access the QUICK MENU. Press key 1followed by the ent key. The
display indicates how many zones have been omitted and the number
of seconds left before setting.
NON-OMITTABLE ZONES
Some open zones may not be eligible for omission from the system.
In this case the display indicates which zones are open and the exit
time is reset. These zones must be closed before setting can continue.
OPTION NOT AVAILABLE
This option is provided by the engineer, where it is specifically
required. Attempting to select an option when it has not been pro-
vided results in the display of OPTION NOT AVAILABLE.
1=RESET ACCESS
2=ABORT ACCESS
ATM PIN + ent
ACCESS TIMEOUT
ATM-2 10 mins
[ent] to Select
1=ATM-1
ATM PIN + ent
[ent] to Select
2=ATM-2
>A
ent
DELAY ACCESS
ATM-2 12 mins
1
2 Zones Open
[<] [>] to View
3 OMITTED 120
ent
1 = FORCED SET
[ent] to select
0 = OMIT ZONES
[ent] to select
PIN + ent
1
Option not
available
Technical Manuals Online! - http://www.tech-man.com

User Guide 10 Galaxy 8/18/60/500/512
CHIME (User Level 3 and above)
PURPOSE
The CHIME mode is switched on and off by this option. When the
CHIME mode is on, any zones that have been programmed by the
engineer for chime will activate momentarily when opened.
NOTE: Your system may not require any zones of this type.
SELECTING CHIME
Enter the QUICK MENU. Press key 2followed by the ent key. The
display shows the ON/OFF status of the CHIME mode. Press the >A
key to toggle between the states and press the ent key to accept the
selection.
NOTE: Keys 1AND 0can also be used to select ON and OFF
respectively.
CHIME IN OPERATION
When switched ON, the CHIME mode remains active until switched
OFF again. Zones that have been programmed with the chime
attribute by the engineer continue to chime when they are activated.
Note: The CHIME mode is suspended while the system is set or
during an alarm.
DISPLAY ZONES (User Level 4 and above)
PURPOSE
This menu option provides the user with a method of checking each
zone for its description and current status.
SELECTING DISPLAY ZONES
Enter the QUICK MENU. Press key 3followed by the ent key.
Details of the first zone (1001) are displayed.
ADDRESS
The zone address provides a unique four digit address number used
for identification and selection, e.g. 1026 - line 1, RIO 02, zone 6
(Galaxy 500).
FUNCTION
The zone function is displayed and identifies the operation of the
zone, e.g. INTRUDER, FIRE.
0 = OMIT ZONES
[ent] to Select
2 = CHIME
[ent] to Select
PIN + ent
> A
CHIME MODE
0 = OFF
2
ent
CHIME MODE
1=ON
ent
0 = OMIT ZONES
[ent] to Select
3 = DISPLAY ZONES
[ent] to Select
PIN + ent
1001 INTRUDER
COMPUTER ROOM
ent
3
Technical Manuals Online! - http://www.tech-man.com

Galaxy 8/18/60/500/512 11 User Guide
STATUS
The current status of the zone is displayed as circuit information, e.g.
Open or Closed. This information alternates with function informa-
tion.
DESCRIPTION
The zone description, if programmed, is displayed on the bottom line
of the display. The descriptor is assembled from alpha-numeric text
and describes the zone in detail, e.g. West Office Door.
SELECTING AND VIEWING
Selecting the DISPLAY ZONES option displays the first zone,
address 1001. Other zones can be viewed sequentially by using the
>A or <B keys. Zones can also be displayed by entering the address
of the zone: Galaxy 8 enter the zone number (1 digit); Galaxy 18 and
60 enter the RIO and zone number (2 digits); Galaxy 500 and 512
enter the line, RIO and zone number (4 digits). Press the #key to
display the zone resistance and RIO voltage.
ESCAPE
The esc key aborts the option and returns to the option menu.
DISPLAY LOG (User Level 4 and above)
PURPOSE
DISPLAY LOG provides the user with a means of viewing the
system history. Events are recorded in detail and stored in the non-
volatile memory.
SELECTING DISPLAY LOG
Enter the QUICK MENU. Press key 4followed by the ent key.
Details of the most recent event to be logged are displayed.
EVENTS
The events available for display include details of setting, unsetting
and alarms. Each event is timed and date stamped.
SELECTING A DATE
Hold down one of the view keys, the dates held in the log are rapidly
stepped through. The A> key moves forward through the dates and
the <B moves backwards. Stopping at the required date reveals the
first event for that date.
1001 INTRUDER
COMPUTER ROOM
2+1
1021 SECURITY
CASHIER DOOR
esc
0 = OMIT ZONES
[ent] to Select
4
4 = DISPLAY LOG
[ent] to Select
ent
PIN + ent
LOG A12345678
Groups YY------
LOG A12345678
Groups NN------
1+2
ent
Technical Manuals Online! - http://www.tech-man.com

User Guide 12 Galaxy 8/18/60/500/512
VIEWING EACH EVENT
The entire events of any one date can be viewed by progressively
stepping through the events using the A> and <B view keys.
ADDITIONAL INFORMATION
The # key can be used to reveal additional information on some types
of events. This information is displayed on the bottom line. The
information includes details such as zone descriptors, user levels and
which keypad was used.
PRINTING
If a serial printer is connected to the system, a system history can be
printed by pressing the Tkey. The system will print from the event
on display until the most recent event.
PRINT (User Level 4 and above)
PURPOSE
The PRINT option gives the user the opportunity to get a hard copy
print-out of the system details. This option requires a serial printer to
be connected to the system.
SELECTING PRINT
Enter the QUICK MENU. Press key 5followed by the ent key. The
system print options are displayed. Pressing the esc key aborts the
PRINT option.
CODES
Press key 1 to start the print-out of all the codes, giving the user
number, name, level and length of code.
ZONES
Select the ZONES option to print-out the details of each zone in the
system. The zone address, function, and descriptor is printed. Press
key 2 to select this option.
LOG
The entire LOG can be printed out by selecting key 3. The print-out
consists of up to 1000 events depending on panel type, and details
the time and date of setting, unsetting and alarms.
0 = OMIT ZONES
[ent] to Select
5
5 = PRINT
[ent] to Select
ent
PIN + ent
PRINTING CODES
ESC to abort
1=CODES 2=ZONES
3=LOG 4=ALL
1
2
08:53 TUE 22 NOV
AC FAIL-RIO108
MON 21 NOV 1999
<B (hold)
MON 20 NOV 1999
release <B
16:31 SUN 20 NOV
FULL SET USR 98
16:31 SUN 20 NOV
KOO L6 A1-------
#
esc
PRINTING LOG
ESC to abort
PRINTING ALL
ESC to abort
PRINTING ZONES
ESC to abort
3
4
ALL
All the options (CODES , ZONES, and LOG) can be printed out by
selecting the ALL option. Pressing key 4delivers a print-out starting
with user codes.
Technical Manuals Online! - http://www.tech-man.com

Galaxy 8/18/60/500/512 13 User Guide
HELP MESSAGE
If a print-out is started without a printer being connected and on-line,
the display indicates that the printer is off-line.
WALK TEST (User Level 5 and above)
PURPOSE
The WALK TEST option provides a method of testing the zones to
ensure that they are operating correctly. There are two options
available:
1. All zones can be tested
2. Selected zones can be tested
In both cases the sounder indicates an open zone. The test is recorded
in the log.
SELECTING WALK TEST
Enter the QUICK MENU. Press the key 6 followed by the ent key.
Once the WALK TEST is selected, TEST ALL ZONES or SE-
LECTED ZONES are displayed.
ALL ZONES
Choosing ALL ZONES (press key 1) starts the test immediately. No
selection is necessary as all valid zones are included in the test. The
sounder operates whenever a zone is opened and stops when all
zones are closed.
NOTE: The TEST ALL ZONES option only tests zones
which can be omitted from the system.
SELECTED ZONES
Choosing the SELECTED ZONES option by pressing key 2 displays
the first zone on the system (zone 1001). Each zone is displayed in
turn by using the >A or <B keys. When the zone to be included in the
test is displayed, press the # key. Other zones can be included in the
test in the same manner. When all of the required zones have been
selected, press the ent key to start the WALK TEST.
NOTE: The SELECTED ZONES option will includes
non-omittable zones.
ENDING WALK TEST
To abort the walk test option press the esc key, otherwise the walk
test option remains active for 20 minutes after the last key press.
0 = OMIT ZONES
[ent] to Select
6
6 = Walk Test
ent to select
ent
PIN + ent
1=TEST ALL ZONES
2=SELECTED ZONES
1
NO ENTRIES
WALK TEST ACTIVE
ESC to abort
1001 FINAL
#=TEST ENT=START
2
>A
1002 EXIT
#=TEST ENT=START
1002 EXIT
TEST ENT=START
#
ent
Printer off-line
Escape to abort
Technical Manuals Online! - http://www.tech-man.com

User Guide 14 Galaxy 8/18/60/500/512
TIME/DATE (User Level 6)
PURPOSE
The TIME/DATE option allows the user to modify both the time
(hours/minutes) and the date (day/month/year).
SELECTING TIME/DATE
Enter the QUICK MENU. Press key 7 followed by the ent key.
Once the TIME/DATE option has been selected, the time or date can
be selected by pressing the A> or <B key.
CHANGING TIME
To change the time press the A> key. The display prompts for a
NEW TIME in hours and minutes (HH:MM). When the new time is
entered, the display immediately returns to the time or date selection
screen. The system does not accept invalid times (greater than 23
hours, greater than 59 minutes). Pressing the esc key aborts the entry.
CHANGING DATE
To change the date press the < B The display prompts for a NEW
DATE in days, months and years (DD/MM/YY). When the new date
is entered, the display momentarily shows the day of the week, before
returning to the time or date selection screen. The system does not
accept invalid dates (e.g. 14/12/99). Pressing the esc key aborts the
entry.
ADVANCE AND RETARD
It is possible to advance and retard the time to compensate for any
variations in clock speed. Press the # key when in the time/date mode
to select the clock speed adjustment. The range is 0 to 120 seconds
per week. Pressing the Tkey will retard the time.
CODES (User Level 6)
PURPOSE
The CODES menu option enables the managers, (user level 6), to
allocate PINs and related information to users. The codes option is
divided into three sub–menus:
1.USER CODES
Sub divided into nine menus (depending on panel used and
whether the group and MAX Mode options are enabled) that
determine all of the access information for users with Personal
Identification Numbers (PINs). This menu also assigns MAX
details to user numbers.
0 = OMIT ZONES
[ent] to Select
7
7 = TIME/DATE
[ent] to Select
PIN + ent
ent
15:25 14/12/1999
A=TIME B=DATE
NEW TIME
--:-- HH:MM
enter time
enter date
NEW DATE
--/--/-- DD/MM/YY
>7
0 = OMIT ZONES
[ent] to Select
8
8 = CODES
[ent] to Select
PIN + ent
ent
CODES
1 = User Codes
15:25 14/12/1999
A=TIME B=Date
Adjustment/week
Ö 010 (0-120) secs
#
(press the Ö key to
retard time)
Technical Manuals Online! - http://www.tech-man.com

Galaxy 8/18/60/500/512 15 User Guide
2. PIN WARNING
Available only on the Galaxy 500 and 512. This option deter-
mines the warning period given to users prior to programmed Pin
Change date.
NOTE: The valid period for Pin Change codes is programmed by
the installation engineer.
3. MAX USERS
This option is only available if the MAX mode is enabled. The
option is subdivided into two menus that assign the MAX card to
users who do not have a PIN assigned.
MANAGER CODE
The manager code is authorised to:
• Program the User Code options for each of the user codes.
• Allocate other codes to user level 6.
• Modify the manager PIN (the manager PIN cannot be deleted)
• Assign the MAX features to the code.
The manager code defaults to group choice when groups are enabled.
The manager is able to toggle the group choice option on and off
(using the Tkey) as required.
GALAXY 8 & 18
The manager code defaults to accessing the quick menu.
SELECTING CODES
Enter the QUICK MENU. Press key 8followed by the ent key.
USER CODES
When the CODES option has been selected, press key 1to access
User Codes. Display each of the user numbers using key A>. Each
user number offers options for PIN, level, name and where applicable
time zones and groups. When the user number to be modified is
displayed, press the ent key to access the Modify PIN option.
>A
CODES
2 = PIN Warning
CODES
3 = MAX Users
>A
0 = OMIT ZONES
[ent] to Select
8
8 = CODES
[ent] to Select
PIN + ent
ent
CODES
1 = User Codes
ent
001 USER
L3
ð
Technical Manuals Online! - http://www.tech-man.com