ADT SafeWatch 3000 User manual

K5309 3/01 Model SASW3000B
1
6DIHZDWFK3UR
6HFXULW\0DQDJHU
6HFXULW\6\VWHPV
8VHU·V*XLGH

– 2 –
IMPORTANT!
PROPER INTRUSION PROTECTION
For proper intrusion coverage, sensors should be located at every possible
point of entry to a home or commercial premises. This would include any
skylights that may be present, and the upper windows in a multi-level building.
In addition, we recommend that radio backup be used in a security system so
that alarm signals can still be sent to the Customer Care Center in the event
that the telephone lines are out of order (alarm signals are normally sent over
the phone lines).
EARLY WARNING FIRE DETECTION
Early warning fire detection is important in a home. Smoke and heat detectors
have played a key role in reducing fire deaths in the United States. With regard
to the number and placement of smoke/heat detectors, we subscribe to the
recommendations contained in the National Fire Protection Association's
National Fire Alarm Code (NFPA 72). These recommendations can be found on
page 34 of this manual.
$ERXW7KLV0DQXDO
This manual is a step-by-step guide that will acquaint you with the system's
features and benefits. It defines the components and their functions, describes
their operation, and provides clear step-by-step instructions for normal and
emergency procedures. Keep this manual in a convenient place so that you can
refer to it as necessary.

– 3 –
7DEOHRI&RQWHQWV
System Overview.................................................................................................................... 5
Introduction.......................................................................................................................... 5
System Basics....................................................................................................................... 5
About The Touchpads ........................................................................................................... 8
General Information.............................................................................................................8
Functions of the Touchpads..............................................................................................10
Entry/Exit Delays.................................................................................................................12
Exit Delay ........................................................................................................................... 12
Entry Delay......................................................................................................................... 12
Exit Alarms......................................................................................................................... 13
Checking For Open Zones..................................................................................................13
Using the [∗] Key................................................................................................................ 13
Arming the System ..............................................................................................................14
Stay Mode: Arms Perimeter Only, Entry Delay On......................................................... 14
Night-Stay Mode: Arms Perimeter Only, Plus Selected Zones....................................... 14
Instant Mode: Arms Perimeter Only, Entry Delay Off.................................................... 14
Away Mode: Arms Entire System, Entry Delay On......................................................... 14
Arming Commands............................................................................................................. 15
Single Button Arming........................................................................................................ 16
Single-Button “Step” Arming............................................................................................. 16
Using the Keyswitch............................................................................................................ 17
Using the Keyswitch .......................................................................................................... 17
Disarming and Silencing Alarms .....................................................................................18
Using the [OFF] key........................................................................................................... 18
Bypassing Protection Zones..............................................................................................19
Using the BYPASS Key ..................................................................................................... 19
Quick Bypass...................................................................................................................... 20
Chime Mode...........................................................................................................................20
Viewing Current Date and Time......................................................................................21
Viewing the Current Date and Time................................................................................. 21
Setting the Date and Time................................................................................................. 21
Panic Keys .............................................................................................................................22
Using Panic Keys................................................................................................................22

– 4 –
7DEOHRI&RQWHQWV
Macro Key Programming & Usage ..................................................................................23
About Macro Keys .............................................................................................................. 23
Example of Macro Programming....................................................................................... 24
Using a Programmed Macro Key ...................................................................................... 24
Using Device Commands....................................................................................................25
Paging Feature.....................................................................................................................26
About Automatic Paging.................................................................................................... 26
Single Button Paging ......................................................................................................... 27
Latch Key Paging ............................................................................................................... 27
Security Codes & Authority Levels .................................................................................28
About Security Codes......................................................................................................... 28
Authority Level Definitions............................................................................................... 28
To assign User Codes and Attributes................................................................................ 29
Accessing Other Partitions (GOTO Command and Multi-Partition Arming)......30
About Accessing Partitions................................................................................................ 30
Using the GoTo Command................................................................................................. 31
Multi-Partition Arming...................................................................................................... 31
Common Zone Operation ................................................................................................... 32
Scheduling .............................................................................................................................33
About Scheduling ............................................................................................................... 33
Creating Schedules............................................................................................................. 33
Event Logging Procedures ................................................................................................35
About Event Logging.......................................................................................................... 35
Viewing the Event Log....................................................................................................... 35
Testing the System (To Be Conducted Weekly)............................................................ 36
Trouble Conditions..............................................................................................................37
Maintaining Your System ..................................................................................................40
Fire Alarm System (If Installed).......................................................................................41
Quick Guide to Basic System Functions........................................................................45
Summary of Audible/Visual Notifications .....................................................................46
Regulatory Statements and Warnings............................................................................48
Charts of Your System's Features.................................................................................... 50

– 5 –
6\VWHP2YHUYLHZ
,QWURGXFWLRQ
Congratulations on your ownership of an ADT Partitioned Security System. You've
made a wise decision in choosing it, for it represents the latest in security protection
technology today, and millions of premises are protected by ADT systems.
This system provides:
•Three forms of protection: burglary, fire* and emergency.
•At least one touchpad which provides control of system operation and displays
the system’s status
•Various sensors for perimeter and interior burglary protection
•Smoke or combustion detectors* designed to provide early warning in case of fire.
Your system may also have been programmed to automatically send alarm or status
messages over the phone lines to a Customer Care Center.
* Commercial installations and some residential systems may not include fire
protection – check with your installer.
6\VWHP%DVLFV
Burglary Protection
•There are four modes of burglary protection: Stay, Night-Stay, Away, Instant.
STAY: arms perimeter zones only and entry delay is on
INSTANT: same as STAY, except entry delay is off
NIGHT-STAY: arms perimeter zones and selected interior zones; entry delay on
AWAY: arms perimeter and all interior zones, entry delay is on
•You can BYPASS selected zones while leaving the rest of the system armed.
•CHIME mode alerts you to the opening of protected doors and windows while the
system is disarmed.
Fire Protection
•Fire protection is always active (if installed) and an alarm sounds if a fire
condition is detected
•If necessary, you can manually initiate a fire alarm using the touchpad.
•Refer to the Fire Alarm System section for information regarding fire protection,
smoke detectors and planning emergency exit routes.
Security Codes
•You were assigned a 4-digit security code during system installation.
•Use your security code when arming and disarming the system, and when
performing other system functions.
•Other users can be assigned different security codes.
•User codes can be assigned different authority levels, which define which system
functions a particular user can perform.

– 6 –
6\VWHP2YHUYLHZ&RQWLQXHG
Zones and Partitions
•The system sensing devices have been assigned to various “zones,” which are
specific areas of protection (e.g., front door, kitchen window, etc.).
•Zone numbers are displayed at the touchpad when an alarm or trouble condition
occurs on a sensor.
•Partitions provide two independent areas of protection, with each partition
containing a group of zones that can be armed and disarmed without affecting
other zones or users.
•Partitioned systems can include a common zone area, which is an area shared by
users of both partitions (such as a lobby in a building).
•Partition identification: 1 = partition 1; 2 = partition 2; 3 = common zone.
Arming, Step-Arming and Disarming Burglary Protection
•The system must be armed before the burglary protection; can sense intrusions.
•To arm your system, enter your user code followed by the desired arming key.
•You can also use the step-arming key to arm the system, if programmed.
•To disarm the system, enter your user code then press the [OFF] key.
•Step-arming, if programmed, lets you use a function key to arm the system in one
of three modes by simply pressing the key repeatedly, where:
first press arms STAY; second press arms NIGHT-STAY; third press arms
AWAY.
Alarms
•When an alarm occurs, both the touchpad and external sounders will sound, and
the touchpad will display the zone(s) causing the alarm.
•If your system is connected to a Customer Care Center, an alarm message will
also be sent.
•To stop the alarm sounding, simply disarm the system.
Memory of Alarm
•When an alarm condition occurs, the touchpad displays the number(s) of the
zone(s) that caused the problem, and displays the type of alarm.
•The message remains displayed even after disarming the system, but can be
cleared with another “off” sequence.

– 7 –
6\VWHP2YHUYLHZ&RQWLQXHG
Phone Access
•If included, a phone module permits you to access the system via a touch-tone
phone, either on-premises or by call-in when away.
•You can receive synthesized voice messages over the telephone regarding the
status of the security system.
•You can arm and disarm the system and perform most function commands
remotely via the telephone, with voice confirmation provided after each command
entry.
•Complete information regarding the use of this feature is provided in a separate
manual entitled “Phone Access User's Guide” that is supplied with the voice
module.
Paging Feature
•If programmed, up to four pagers can automatically display certain system
conditions as they occur in your system.
•The display consists of code numbers that indicate the type of condition that has
occurred.
Function Keys
•The “A”, “B”, “C”, and “D” keys on the touchpad can be programmed to perform
various functions.
•Functions include: activate a Panic alarm; arm the system; provide step arming;
switch lights on/off; send a message to a pager; display Time/Date; start a Macro
Scheduling
•Your system can be programmed to automatically perform certain functions (e.g.,
arm the system) at a predetermined time each day.

– 8 –
$ERXW7KH7RXFKSDGV
*HQHUDO,QIRUPDWLRQ
Your touchpads allow you to control all system functions. The touchpads feature the
following:
•A telephone style (digital) keypad
•Liquid Crystal Display (LCD) which shows the nature and location of all
occurrences
•Built-in sounder which will sound during alarms and troubles. The sounder also
"beeps" during certain system functions and when depressing any of the keys (to
acknowledge the key press).
•Backlighting of the LCD display windows. Backlighting turns on when entering the
premises through any assigned entry/exit door, or when any touchpad key is
pressed. This feature is helpful when a touchpad is located in a dimly lit area.
IMPORTANT: If the touchpad beeps rapidly upon entering the premises, it indicates
that an alarm has occurred during your absence and an intruder may still be on the
premises. LEAVE IMMEDIATELY and CONTACT THE POLICE from a nearby safe
location.
There are two basic types of touchpads which are functionally the same, but they
have different types of displays.
Custom English Display 2-line Custom English display touchpads feature a 2-line,
32-character alphanumeric LCD which can display system
messages in friendly English. These touchpads can also be
programmed with custom zone descriptors. To access the
keys on the touchpad, simply open the swing-down door.
English Display English display touchpads are functionally identical to
Custom English display touchpads, but the LCD display
uses pre-designated words to identify the nature and
location of occurrences. To access the keys on the touchpad,
simply open the swing-down door.

– 9 –
$ERXW7KH7RXFKSDGV&RQWLQXHG
(QJOLVK'LVSOD\7RXFKSDG
AWAY: All burglary zones, interior and
perimeter, are armed.
STAY: Perimeter burglary zones, such as
protected windows and doors, are
armed.
INSTANT: Perimeter burglary zones armed
and entry delay is turned off.
ALARM
FIRE
AWAY
BYPASS
STAY
CHECK INSTANT
NO AC
TEST
NOT READY
CHIME BAT
ENGLISH DISPLAY TOUCHPAD
BYPASS: This appears when one or more burglary protection zones have been
bypassed.
NOT READY: Appears when burglary portion of the system is not ready for arming
(due to open protection zones). The system is ready to arm when this
message disappears and the READY indicator light comes on.
NO AC: Appears when AC power has been cut off. System is operating on
backup battery power.
AC: Appears when AC power is present.
CHIME: Appears when the CHIME feature is activated.
BAT: Low battery condition in a wireless sensor (if zone number displayed)
or low system battery (if no zone number displayed).
ALARM: Appears when an intrusion has been detected and the system is armed
(also appears during a fire alarm or audible emergency alarm).
Accompanied by the protection zone in alarm.
CHECK: Appears when a malfunction is discovered in the system at any time or
if an open is detected in a FIRE zone at any time or a fault in a
DAY/NIGHT burglary zone during a disarmed period. Accompanied by
a display of zone number in trouble.
FIRE:Appears when a fire alarm is present. Accompanied by a display of the
zone in alarm.
A FIRE display, accompanied by a display of zone 95, also appears
when a fire alarm is manually activated.

– 10 –
)XQFWLRQVRIWKH7RXFKSDGV
1. DISPLAY WINDOW.
Custom English Display Touchpads: 2-
line, 32-character Liquid Crystal Display
(LCD) touchpads that display protection point
identification, system status, and messages.
English Display Touchpads: Display
protection zone ID and system status
messages using pre-designated words in the
LCD display.
2. 1 OFF Disarms burglary portion of the
system, silences alarms and audible trouble
indicators, and clears visual display after
problem's correction.
3. 2 AWAY Arms the entire burglary system,
perimeter and interior.
4. 3 STAY Arms perimeter portion of burglary
system only. Interior protection is not armed,
allowing movement within premises
without causing an alarm.
5. 4 This is not a Function key. Used
only as a numeric key.
6. 5TEST Tests the system and alarm
sounder if disarmed. Refer to Testing The
System section for test procedures.
7. 6BYPASS Removes individual protection
zones from being monitored by the system.
8. 7INSTANT Arms in manner similar to the
STAY mode, but without the entry delay
feature. Entering via an entry/exit door will
cause an instant alarm.
9. 8CODE Used to assign additional user
codes for other users of the system.
10. 9 CHIME Turns CHIME mode on and off.
When on, the opening of windows or doors
while the system is disarmed will sound 3
beeps at the touchpad(s).
11. ✱READY Used to display all open protection
zones.
12. #This key can be used for "Quick
Arming" of the system without use of a
security code (if programmed).
13. KEYS 0–9†:Used to enter your security
code(s).
14. READY INDICATOR: (GREEN) Lit when
the system is ready to be armed (no faults
present). While the system is disarmed, this
indicator will go on and off as protection
zones are closed and opened.
15. ARMED INDICATOR: (RED) Lit when the
system has been armed.
16. INTERNAL SOUNDER: The built-in
sounder mimics the alarm sounder during
alarms, and will also "beep" during certain
system functions.
17. FUNCTION KEYS: Keys A, B, C, D may
have been programmed for a variety of
functions, including panic (emergency)
functions. For details, see the Function Keys
section.
†Note: Keys 1 OFF through 3 STAY and 2 AWAY through 7INSTANT each perform their
associated companion system functions (OFF, STAY, AWAY, INSTANT, etc.) when
preceded by an entry of the security code (as described later).

– 11 –
)XQFWLRQVRIWKH7RXFKSDGV&RQWLQXHG
ARMED READY
6
BYPASS
7
INSTANT
1
OFF AWAY STAY
23
4
TEST
CODE CHIME
READY
9
8
5
#0
A
C
D
B
1
4
3
2
17
5
18
8
11
15
14
16
6
7
9
10
12
13
English Display Touchpad
ARMED READY
6
BYPASS
7
INSTANT
1
OFF AWAY STAY
23
4
TEST
CODE CHIME
READY
9
8
5
#0
A
C
D
B
KEYPAD SHOWN WITHOUT SWING-DOWN FRONT DOOR
1
4
3
2
17
5
18
8
11
15
14
16
6
7
9
10
12
13
Custom English Display Touchpad
(Touchpads shown without swing-down front door)
IMPORTANT!
• When entering codes and commands, sequential key depressions must be made
within 10 seconds of one another. If 10 seconds elapse without a key
depression, the entry will be aborted and must be repeated from its beginning.
Be sure to observe this precaution when performing any of the procedures in
this manual.
•If you make a mistake while entering a security code, stop, press the [✱] key,
and then start over. If you stop in the middle while entering a code, and then
immediately start the entry over, an erroneous code might be entered.

– 12 –
(QWU\([LW'HOD\V
Your system has preset time delays, known as exit delay and entry delay.
([LW'HOD\
Exit delay gives you time to leave through the designated exit door without setting
off an alarm. Exit delay begins immediately after arming your system in any
arming mode and Custom Display touchpads display the message “You May Exit
Now.” When “You may exit now” disappears, the system is fully armed. If programmed, a
slow beeping will sound throughout the exit delay period.
Exit Delay Restart. If you wish to open the entry/exit door to let someone in after arming
STAY, you can re-start the exit delay at any time – simply press the [✱] key, then let that
person in. This avoids having to disarm the system and then re-arm it again.
(QWU\'HOD\
Entry Delays give you time to disarm the system when you re-enter through the
designated entrance door. But you must disarm the system before the entry delay
period ends, or an alarm will occur. The touchpad beeps during the entry delay
period, reminding you to disarm the system. There are two entry delays (if
programmed). The first is for your primary entrance and the second can be used for
a secondary entrance, where a longer delay is required to walk to the touchpad to
disarm the system.
You can also arm the system with no entry delay at all by using the INSTANT
arming mode. This mode provides greater security while on the premises or while
away for extended periods of time.
See your installer for your delay times.
Partition 1 __________________________________________________________
Exit Delay: seconds Entry Delay 1: seconds
Entry Delay 2: seconds
NOTE: Entry/Exit times set for partition 1 also apply to the common zone.
Partition 2 __________________________________________________________
Exit Delay: seconds Entry Delay 1: seconds
Entry Delay 2: seconds

– 13 –
(QWU\([LW'HOD\V&RQWLQXHG
([LW$ODUPV
Whenever you arm the system, the exit delay begins. If an entry/exit door or interior
zone is faulted when the exit delay ends (e.g., exit door left open), the system sounds
an alarm and starts the entry delay timer. If you disarm the system before the entry
delay ends, the alarm sound stops and the message "CANCELED ALARM" or "CA" is
displayed on the touchpad, along with a zone number indicating the faulted zone. No
message is sent to the Customer Care Center.
To clear the exit alarm condition, the open zone must be made intact; to clear the
display, enter your code plus OFF.
If you do not disarm the system before the entry delay ends, and an entry/exit door or
interior zone is still open, the alarm sound continues and an "exit alarm" message is
sent to the Customer Care Center. The message ""EXIT ALARM" or "EA" is displayed
on the touchpad, along with a zone number indicating the faulted zone. To stop the
alarm, the system must be disarmed (your code plus OFF); to clear the display, enter
your code plus OFF a second time.
An “exit alarm” also results if an entry/exit door or interior zone is faulted within two
minutes after the end of the exit delay.
Your system may have been programmed for this feature to minimize false alarms sent to the Customer
Care Center. Ask your installer if "Exit Alarm" is active in your system. If so, check this box.
&KHFNLQJ)RU2SHQ=RQHV
8VLQJWKH>∗@.H\
Before arming your system, all protected doors, windows and other protection zones
must be closed or bypassed, otherwise the touchpad will display a "Not Ready"
message.
Use the READY key to display all faulted zones, making it easier for you to identify
and secure any open zone.
1. Press [∗] (do not enter code first) to display faulted
zones.
2. Secure or bypass the zones displayed.
3. The touchpad’s READY indicator lights when all
protection zones have been either closed or bypassed.
4. Arm the system as desired.
Custom Display:
(-7%61)(  46)77
∗
83 7,3; *%9087
English Display:
Zone no. and “NOT READY”

– 14 –
$UPLQJWKH6\VWHP
6WD\0RGH$UPV3HULPHWHU2QO\(QWU\'HOD\2Q
•Used when you want to arm the system with persons staying inside (or if you have
pets that are moving throughout the premises).
•The perimeter sensors are armed, but interior sensors are left disarmed.
•Exit delay begins (you can leave through the entry/exit door, if desired).
•An alarm sounds immediately if any protected perimeter window or non-entry/exit
door is opened.
•You may otherwise move freely within the premises.
•Persons entering later can enter through an entry/exit door without causing an
alarm, but they must disarm the system within the entry delay period to avoid
sounding an alarm.
1LJKW6WD\0RGH$UPV3HULPHWHU2QO\3OXV6HOHFWHG=RQHV
•Use Night-Stay mode to provide increased security while staying inside.
•Arms same as Stay mode, but also arms pre-selected interior sensors (programmed
by your installer), while other interior sensors are left disarmed.
•Persons entering later can use an entry/exit door but must not violate any of the
programmed interior zones to avoid sounding an alarm.
•IMPORTANT: When Night-Stay mode is on, the selected interior zones are armed
and cause an alarm if anyone enters those areas (e.g., waking in the middle of the
night). To avoid sounding an alarm, you must disarm the system before any
activity takes place in those interior zones.
,QVWDQW0RGH$UPV3HULPHWHU2QO\(QWU\'HOD\2II
•Used when staying inside and do not expect anyone to use an entry/exit door.
•Arms same as Stay mode.
•An alarm sounds immediately if any protected perimeter window or any door is
opened, including entry/exit doors.
•IMPORTANT: Arming the system in this mode greatly increases the chance of
false alarms. Use extreme care in selecting this mode of arming.
$ZD\0RGH$UPV(QWLUH6\VWHP(QWU\'HOD\2Q
•Used when nobody will be staying inside (including pets).
•The entire system (interior and perimeter) is armed.
•Exit delay begins letting you leave through the entry/exit door.
•An alarm sounds if a protected window or any door is opened, or if any movement
is detected inside your premises.
•You can reenter through an entry/exit door without causing an alarm, but you
must disarm the system within the entry delay period to avoid sounding an alarm.

– 15 –
$UPLQJWKH6\VWHP
$UPLQJ&RPPDQGV
Before arming, close all perimeter doors and windows and make sure the Ready to Arm
message is displayed.
Mode Press these keys… Touchpad Confirms By…
Stay security code + [3] (STAY) •three beeps
•armed STAY message displayed
•red ARMED indicator lights
Night-Stay security code + [3] + [3] •three beeps
•NIGHT-STAY message displayed
•red ARMED indicator lights
Instant security code + [7] (INSTANT) •three beeps
•armed STAY message displayed
•red ARMED indicator lights
Note that entry delay is turned off.
Away security code + [2] (AWAY) •beeping for duration of exit delay
•armed AWAY message displayed
•red ARMED indicator lights
Leave the premises through an entry/exit
door during the exit delay period to avoid
causing an alarm. The touchpad beeps
rapidly during the last 5 seconds of the
exit delay to warn you that it is ending.
Quick Arming
If "Quick Arming" was programmed by the installer, the [#] key can be pressed in
place of the security code when arming the system. However, the security code
must always be used to disarm the system.
Function Key Arming
For any arming command, a function key may have also been programmed for your system. If
so, you can press and hold the appropriate function key for 2 seconds to arm the system. See
your installer for the designated functions (see Single Button Arming section).
Refer to the Accessing Other Partitions section for information on multi-partiion
arming.

– 16 –
$UPLQJWKH6\VWHP
6LQJOH%XWWRQ$UPLQJ
The “A”, “B”, “C”, and/or “D” keys on your touchpad may have been programmed for
single-button arming. Note that while it will not be necessary to use a security code
for arming, a security code must always be used to disarm the system.
If Single-Button Arming is programmed:
•A function key has been assigned to a specific type of arming: STAY mode,
Night-STAY mode, AWAY mode, or STEP-ARMING (see Step-Arming
paragraph).
•You DO NOT need to enter your user code before pressing the function key
(you always need your user code to DISARM the system).
Before arming, close all perimeter doors and windows.
1. Press and hold the assigned function key for 2
seconds (no code is required). Function keys are
shown below.
321
654
987
#0
*
READY
INSTANT
OFF
CODE
AWAY
TEST
CHECK
STAY
BYPASS
A
B
C
D
ADT3000-007-V0
(-7%61)(
6)%(= 83 %61
English Display: READY
2. The touchpad begins beeping and displays the
armed message. The red ARMED indicator also
lights.
%61)(%;%=
=39 1%= )<-8 23;
English Display: AWAY
6LQJOH%XWWRQ´6WHSµ$UPLQJ
Single-Button “Step” arming may have been programmed into one of the lettered keys
(A, B, C, or D). Check with your installer to see if this has been done in your system.
If Step-Arming is programmed:
•The assigned key provides a choice of three levels of security.
•The selected key can be pressed once, twice, or three times, increasing the level
of security with each press, as follows
Key
Ø
First Press
Ø
Second Press
Ø
Third Press
Ø
A, B, C, D Armed-STAY Armed Night-STAY Armed-AWAY

– 17 –
8VLQJWKH.H\VZLWFK
8VLQJWKH.H\VZLWFK
Your system may be equipped with a keyswitch for use when arming and disarming.
Red and green lights on the keyswitch plate indicate the status of your system as
follows:
Green Light: Lights when the system is disarmed and ready to be armed (no
open zones). If the system is disarmed and the green light is off, it
indicates the system is not ready (one or more zones are open).
Red Light: Lights or flashes when system is armed in AWAY or STAY mode.
See your installer for the meanings of the lit red light:
Lit Steady = system armed AWAY or
system armed STAY and exit delay has expired
Flashing = system armed STAY and exit delay timer active
Rapid flashing = an alarm has occurred (memory of alarm).
Before arming, close all perimeter doors and windows.
To arm in the AWAY mode:
Turn the key to the right for 1/2 second and release.
Touchpads beep twice and the red indicator lights or
flashes.
To arm in the STAY mode:
Turn the key to the right and hold for longer than 1
second, then release. Touchpads beep three times
and the red indicator lights or flashes.
To disarm the system:
Turn the key to the right and release. The red light
turns off
GREEN RED

– 18 –
'LVDUPLQJDQG6LOHQFLQJ$ODUPV
8VLQJWKH>2))@NH\
The OFF key is used to disarm the system, silence alarm and trouble sounds, and
clear alarm memories.
IMPORTANT: If you return and the main burglary sounder is on, DO NOT ENTER, but
CONTACT THE POLICE from a nearby safe location.
If you return after an alarm has occurred and the main sounder has shut itself off, the touchpad
will beep rapidly upon your entering, indicating that an alarm has occurred during your
absence.
LEAVE AT ONCE, and CONTACT THE POLICE from a nearby safe location.
1. + 1
(Security Code) OFF
The “READY” indicator light will be lit if all zones
are secure, and the touchpad will emit a single tone
to confirm that the system is disarmed.
(-7%61)(
6)%(= 83 %61
English Display:
2.
To Silence a Burglary Alarm and Clear a Memory of
Alarm
Enter your security code and press the OFF key to
silence the alarm (or warning tones of a Memory of
Alarm).
Note the zone in alarm on the touchpad display, and
make that zone intact (close door, window, etc.). Now
enter the security code plus OFF sequence again to
clear the touchpad’s Memory of Alarm display.
Note the zone in alarm on the touchpad display, and
make that zone intact (close door, window, etc.). Now
enter the security code plus OFF sequence again to
clear the touchpad’s Memory of Alarm display.
3. To Silence a Fire Alarm and Clear Memory of Alarm
Simply press the OFF key to silence the alarm. Then
enter the security code plus OFF sequence to clear
the touchpad's Memory of Alarm display. See the
Fire Alarm System section.

– 19 –
%\SDVVLQJ3URWHFWLRQ=RQHV
8VLQJWKH%<3$66.H\
Use this key when you want to arm your system with one or more zones intentionally
unprotected. The system must be disarmed first.
When bypassing zones:
•Your system may have been set so that arming will not be possible if more than
one zone is bypassed (check with your installer).
•The system must be disarmed before you can bypass zones.
•Bypassed zones are unprotected and will not cause an alarm if violated.
•The system will not allow fire zones to be bypassed.
•Zones are automatically unbypassed when the system is disarmed.
1. + 6 + zone numbers (see below)
(Security Code) BYPASS
Enter the 2-digit zone number(s) for the zone(s) to be
bypassed (e.g., 06, 10, 13, etc.). Single digit zone
numbers must be preceded by a zero (e.g. 05, 06).
(-7%61)(  46)77
 83 7,3; *%9087
English Display:
NOT READY
2. When finished, the touchpad will momentarily
display a "Bypass" message for each bypassed zone
number. Wait for all bypassed zones to be displayed.
Arm the system as usual.
To display bypassed zones prior to arming, enter
your security code and press the [6] BYPASS key.
(-7%61)( &=4%77
6)%(= 83 %61
English Display: BYPASS

– 20 –
%\SDVVLQJ3URWHFWLRQ=RQHV
4XLFN%\SDVV
If programmed, "Quick Bypass" allows you to easily bypass all open (faulted) zones
without having to enter zone numbers individually. This feature is useful if, for
example, you routinely leave certain windows open when arming at night.
1. + 6 + [#]
(Security Code) BYPASS
In a few moments, all open zones will be displayed
and automatically bypassed. Make sure that only those
zones that you wish to leave unprotected are bypassed, and
that there are no other zones unintentionally left open.
(-7%61)(  46)77
 83 7,3; *%9087
English Display:
NOT READY
2. Wait for all bypassed zones to be displayed, then arm
the system as desired.
(-7%61)( &=4%77
6)%(= 83 %61
English Display: BYPASS
Ask your installer if "Quick Bypass" is active for your system, and if so, check here:
&KLPH0RGH
CHIME mode alerts you to the opening of a perimeter door or window while the
system is disarmed.
When Chime mode is activated:
•Three tones sound at the touchpad whenever a perimeter door or window is opened.
•Interior zones do not produce a tone when they are faulted.
•Pressing the READY key will display the open protection points.
•Chime mode can be used only while the system is disarmed.
To turn Chime Mode on:
+ 9
(Security Code) CHIME
The CHIME message will appear. Perimeter zones
will cause a tone when faulted.
(-7%61)(
6)%(= 83 %61
English Display: READY
To turn Chime Mode off:
+ 9 again
(Security Code) CHIME
The CHIME message will disappear.
(-7%61)( ',-1)
6)%(= 83 %61
English Display: CHIME