ADT Ademco Vista 20P/PSIA User manual

For a detailed review of the entire system, please view the Ademco Vista –20P/PSIA system manual.
Arm and Disarm
Arm:
To arm in STAY mode, when you are not leaving the premises, enter your [security code] + [3].
To arm in AWAY mode, when you are leaving the premises, enter your [security code] + [2].
To arm in MAXMIMUM mode, when no one will be in or around the premises for long periods of time,
enter your [security code] + [4].
Disarm:
To disarm, enter you’re security code] + [1].
Quick Guide: Ademco Vista –20P/PSIA

Battery
The Ademco Vista 20P/PSIA operates on a UB 1270 battery.
Loss of AC power and use of backup battery power is indicated by NO AC.
A low battery condition is indicated by BAT or SYSTEM LO BAT
For instructions on replacing your battery, please visit our Battery Replacement Page.
Bypassing Protected Areas
Bypassing a zone allows you to arm your system with certain protected areas intentionally unarmed or to
access a protected area when the system is armed.
To bypass a zone, enter your [security code] + [6] + [zone number].
Once the panel displays “BYPASS”, arm the system as usual.
To display all bypassed zones, press [6].
To unbypass a zone, disarm the system.
Change Time and Date
To change date and time settings, enter your [security code] + [#] + [6] + [3].
Wait until time/date are displayed, then press [*] to move the cursor ahead and [#] to move back.
Enter the 2-digit hour and minute settings, i.e., [06] and [17] for 6:17.
Press [1] for PM or [0] for AM.
Continue to enter 2-digit year, month, and day settings, i.e., [15], [08], and [23] for August 23, 2015.
To exit, press [*] when the cursor is on the last digit.
Chimes and Beeps
When your system is in chime mode, a chime alert will sound three tones whenever a protected door/window
is opened.
To turn chime mode on and off, enter your [security code] + [9].
To turn voice chime mode on and off, press [#] + [0] + [2] + [4]. Voice chime can only be activated
when chime mode is on.

Reset
To silence an alarm and to clear memory of an alarm event, enter the [security code] + [1] sequence twice.
Security Codes
Your system will allow different security codes for use by other users, however only the Master user or
Partition Programmer can assign user codes to users.
Users are also assigned an Authority Level, which defines the functions a particular user can and cannot
perform.
To add a user code, enter your [Master/Partition Programmer code] + [8] + [user number] + [new
user’s code].
To delete a user code, enter your [Master/Part. Prog code] + [8] + [user number] + [#] + [0].
To assign an authority level, enter your [Master/Part. Prog code] + [8] + [user number] + [#] + [1] +
[authority level].
Some user authority levels have been pre-programmed:
User Authority Level
Explanation
Code to assign to user
Standard
Can only perform security
function in assigned
partitions.
[0]
Arm Only
Can only arm the system.
[1]
Guest
Can arm the system in
assigned partitions, but
cannot disarm the system
unless the system was armed
with this code. Perfect for
babysitters, cleaners, etc.
[2]
Duress
Intended for use for when
you are forced to arm or
disarm the system against
your will.
[3]
Partition Programmer
Can do everything a Standard
user can do plus assigning
[4]

user codes to partitions.
For a complete list of use authority levels and partitions, please see the Ademco Vista –20P/PSIA system
manual.
Trouble Conditions
Trouble conditions are issues that require your attention and are indicated on your panel’s display by the
word CHECK + zone number and accompanied by beeping from the touchpad.
To silence Trouble Conditions beeping, check that the zone’s protected areas are closed and secure.
For wireless sensors, check that no environmental changes have blocked the wireless sensor.
If the problem is corrected, enter the [security code] + [OFF] sequence twice.
For a list of Trouble Conditions other than CHECK, please see your Ademco Vista –20P/PSIA system
manual.
Volume
The voice touchpad’s voice message volume can be adjusted. Adjusting the voice message volume also
adjusts the status beeps volume.
To adjust the volume, press [#] + [0] + [2].
Choose [3] to increase the volume and [6] to decrease the volume.