ADTRAN NetVanta 900 Series Manual

NetVanta 950 IAD
Hardware Installation Guide
1200785L1 NetVanta 900 Series AC Power Supply
1200786L1 NetVanta 900 Series AC Chassis
1200788L1 NetVanta 950 IAD System Controller
1200791L1 NetVanta 900 Series Octal FXS Module
1200792L1 NetVanta 900 Series Octal FXO Module
1200793L1 NetVanta 900 Series Octal Ethernet Switch Module
1200798L1 NetVanta 950 IAD T1/V.35 Expansion Module
61200788L1-34B
July 2004

Hardware Installation Guide NetVanta 950 IAD
2 © 2004 ADTRAN, Inc. 61200788L1-34B
Trademarks
Any brand names and product names included in this manual are trademarks, registered trademarks, or
trade names of their respective holders.
To the Holder of this Manual
The contents of this manual are current as of the date of publication. ADTRAN reserves the right to change
the contents without prior notice.
In no event will ADTRAN be liable for any special, incidental, or consequential damages or for
commercial losses even if ADTRAN has been advised thereof as a result of issue of this publication.
901 Explorer Boulevard
P.O. Box 140000
Huntsville, AL 35814-4000
Phone: [phone]
www.adtran.com
©2004 ADTRAN, Inc.
All Rights Reserved.
Printed in U.S.A.

NetVanta 950 IAD Hardware Installation Guide
61200788L1-34B © 2004 ADTRAN, Inc. 3
Conventions
Safety Instructions
When using your communications equipment, please follow these basic safety precautions to reduce the
risk of fire, electrical shock, or personal injury:
1. Do not use this product near water such as a bathtub, wash bowl, kitchen sink, laundry tub, in a
wet basement, or near a swimming pool.
2. Avoid using a telephone (other than a cordless-type) during an electrical storm. There is a remote
risk of shock from lightning.
3. Do not use a telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord, power supply, and/or batteries indicated in the manual. Do not dispose of
batteries in a fire. They may explode. Check with local codes for special disposal instructions.
Save These Important Safety Instructions
Notes provide additional useful information.
Cautions signify information that could prevent service interruption.
Warnings provide information that could prevent damage to the equipment or
endangerment to human life.

Hardware Installation Guide NetVanta 950 IAD
4 © 2004 ADTRAN, Inc. 61200788L1-34B
Affidavit Requirements for Connection to Digital Services
• An affidavit is required to be given to the telephone company whenever digital terminal equipment
(DTE) without encoded analog content and billing protection is used to transmit digital signals
containing encoded analog content intended for eventual conversion into voiceband analog signals and
transmitted on the network.
• The affidavit shall affirm that either no encoded analog content or billing information is being
transmitted or that the output of the device meets Part 68 encoded analog content or billing protection
specifications.
• The end user/customer will be responsible for filing an affidavit with the local exchange carrier when
connecting unprotected customer premise equipment (CPE) to 1.544 Mbps or subrate digital services.
• Until such time as subrate DTE is registered for voice applications, the affidavit requirement for subrate
services is waived.

NetVanta 950 IAD Hardware Installation Guide
61200788L1-34B © 2004 ADTRAN, Inc. 5
Affidavit for Connection of Customer Premises Equipment
to 1.544 Mbps and/or Subrate Digital Services
For the work to be performed in the certified territory of ___________________ (telco name)
State of ________________
County of ________________
I, _______________________ (name), ____________________________________ (business address),
____________________ (telephone number) being duly sworn, state:
I have responsibility for the operation and maintenance of the terminal equipment to be connected to 1.544 Mbps and/or
________ subrate digital services. The terminal equipment to be connected complies with Part 68 of the FCC rules except
for the encoded analog content and billing protection specifications. With respect to encoded analog content and billing
protection:
( ) I attest that all operations associated with the establishment, maintenance, and adjustment of the digital CPE with respect to
analog content and encoded billing protection information continuously complies with Part 68 of the FCC Rules and
Regulations.
( ) The digital CPE does not transmit digital signals containing encoded analog content or billing information which is intended
to be decoded within the telecommunications network.
( ) The encoded analog content and billing protection is factory set and is not under the control of the customer.
I attest that the operator(s)/maintainer(s) of the digital CPE responsible for the establishment, maintenance, and
adjustment of the encoded analog content and billing information has (have) been trained to perform these functions by
successfully having completed one of the following (check appropriate statements):
( ) A. A training course provided by the manufacturer/grantee of the equipment used to encode analog signals; or
( ) B. A training course provided by the customer or authorized representative, using training materials and instructions
provided by the manufacturer/grantee of the equipment used to encode analog signals; or
( ) C. An independent training course (e.g., trade school or technical institution) recognized by the manufacturer/grantee of the
equipment used to encode analog signals; or
( ) D. In lieu of the preceding training requirements, the operator(s)/maintainer(s) is (are) under the control of a supervisor
trained in accordance with _________ (circle one) above.
I agree to provide ______________________ (telco’s name) with proper documentation to demonstrate compliance with the
information as provided in the preceding paragraph, if so requested.
_________________________________Signature
_________________________________Title
_________________________________ Date
Transcribed and sworn to before me
This ________ day of _______________, _______
_________________________________
Notary Public
My commission expires:
_________________________________

Hardware Installation Guide NetVanta 950 IAD
6 © 2004 ADTRAN, Inc. 61200788L1-34B
FCC regulations require that the following information be provided in this manual:
1. This equipment complies with Part 68 of FCC rules and requirements adopted by ACTA. Each
registered interface has a label that contains, among other information, a product identifier in the
format US:AAAEQ##TXXXX. If requested, provide this information to the telephone company.
2. If this equipment causes harm to the telephone network, the telephone company may temporarily
discontinue service. If possible, advance notification is given; otherwise, notification is given as
soon as possible. The telephone company will advise the customer of the right to file a complaint
with the FCC.
3. The telephone company may make changes in its facilities, equipment, operations, or procedures
that could effect the proper operation of this equipment. Advance notification and the opportunity
to maintain uninterrupted service are given.
4. If experiencing difficulty with this equipment, please contact ADTRAN for repair and warranty
information. The telephone company may require this equipment to be disconnected from the
network until the problem is corrected or it is certain the equipment is not malfunctioning.
5. This unit contains no user-serviceable parts.
6. This equipment is designed to connect to the telephone network or premises wiring using an
FCC-compatible modular jack, which is compliant with Part 68 and requirements adopted by
ACTA.
7. The following information may be required when applying to the local telephone company for
leased line facilities:
8. The REN is useful in determining the quantity of devices you may connect to your telephone line
and still have all of those devices ring when your number is called. In most areas, the sum of the
RENs of all devices should not exceed five. To be certain of the number of devices you may
connect to your line as determined by the REN, call your telephone company to determine the
maximum REN for your calling area.
9. This equipment may not be used on coin service provided by the telephone company. Connection
to party lines is subject to state tariffs. Contact your state public utility commission or corporation
commission for information.
Part Number
Registration
Number Service Type REN/SOC FIC USOC
1200786L1 US: HDCDFNAN1200788L1 1.544 Mbps - SF
1.544 Mbps - SF and B8ZS
1.544 Mbps - ESF
1.544 Mbps - ESF and B8ZS
6.0N
04DU9-BN
04DU9-DN
04DU9-1KN
04DU9-1SN
RJ-48C
1200798L1 US: HDCDENAN1200798L1
1200792L1 US: HDCKX03B1200792L1 Analog Loop Start/Ground
Start
0.3B/9.0F 02LS2/02GS2 RJ-11C

NetVanta 950 IAD Hardware Installation Guide
61200788L1-34B © 2004 ADTRAN, Inc. 7
Federal Communications Commission Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio frequencies. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Canadian Emissions Requirements
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus
as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the
Department of Communications.
Cet appareil numérique respecte les limites de bruits radioelectriques applicables aux appareils numériques
de Class A prescrites dans la norme sur le materiel brouilleur: “Appareils Numériques,” NMB-003 edictee
par le ministre des Communications.
Industry Canada Compliance Information
Notice: The Industry Canada label applied to the product (identified by the Industry Canada logo or the
“IC:” in front of the certification/registration number) signifies that the Industry Canada technical
specifications were met.
Notice: The Ringer Equivalence Number (REN) for this terminal equipment is supplied in the
documentation or on the product labeling/markings. The REN assigned to each terminal device indicates
the maximum number of terminals that can be connected to a telephone interface. The termination on an
interface may consist of any combination of devices subject only to the requirement that the sum of the
RENs of all the devices should not exceed five (5).
Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.

Hardware Installation Guide NetVanta 950 IAD
8 © 2004 ADTRAN, Inc. 61200788L1-34B
Product Warranty
ADTRAN will repair and return this product within the warranty period if it does not meet its published
specifications or fails while in service. Warranty information can be found at www.adtran.com/warranty.
Product Registration
Registering your product helps ensure complete customer satisfaction. Please take time to register your
products on line at www.adtran.com. Click Service and Support on the top of the page, and then click
Product Registration under Support.
Customer Service, Product Support Information, and Training
ADTRAN will repair or return this product within the warranty period if it does not meet its published
specifications or fails while in service. Warranty information can be found at www.adtran.com/warranty.
A return material authorization (RMA) is required prior to returning equipment to ADTRAN. For service,
RMA requests, training, or more information, use the contact information given below.
Repair and Return
If you determine that a repair is needed, please contact our Customer and Product Service (CaPS)
department to have an RMA number issued. CaPS should also be contacted to obtain information
regarding equipment currently in house or possible fees associated with repair.
Identify the RMA number clearly on the package (below address), and return to the following address:
Pre-Sales Inquiries and Applications Support
Your reseller should serve as the first point of contact for support. If additional pre-sales support is needed,
the ADTRAN Support web site provides a variety of support services such as a searchable knowledge
base, latest product documentation, application briefs, case studies, and a link to submit a question to an
Applications Engineer. All of this, and more, is available at:
When needed, further pre-sales assistance is available by calling our Applications Engineering
Department.
CaPS Department [phone]
ADTRAN Customer and Product Service
901 Explorer Blvd. (East Tower)
Huntsville, Alabama 35806
RMA # _____________
http://support.adtran.com
Applications Engineering [phone]

NetVanta 950 IAD Hardware Installation Guide
61200788L1-34B © 2004 ADTRAN, Inc. 9
Post-Sale Support
Your reseller should serve as the first point of contact for support. If additional support is needed, the
ADTRAN Support web site provides a variety of support services such as a searchable knowledge base,
updated firmware releases, latest product documentation, service request ticket generation and
trouble-shooting tools. All of this, and more, is available at:
When needed, further post-sales assistance is available by calling our Technical Support Center. Please
have your unit serial number available when you call.
Installation and Maintenance Support
The ADTRAN Custom Extended Services (ACES) program offers multiple types and levels of installation
and maintenance services which allow you to choose the kind of assistance you need. This support is
available at:
For questions, call the ACES Help Desk.
Training
The Enterprise Network (EN) Technical Training Department offers training on our most popular products.
These courses include overviews on product features and functions while covering applications of
ADTRAN's product lines. ADTRAN provides a variety of training options, including customized training
and courses taught at our facilities or at your site. For more information about training, please contact your
Territory Manager or the Enterprise Training Coordinator.
http://support.adtran.com
Technical Support (888) 4ADTRAN
http://www.adtran.com/aces
ACES Help Desk (888) 874-ACES (2237)
Training Phone [phone], ext. 7500
Training Fax [phone]
Training Email [e-mail]

Hardware Installation Guide NetVanta 950 IAD
10 © 2004 ADTRAN, Inc. 61200788L1-34B

61200788L1-34B © 2004 ADTRAN, Inc. 11
TABLE OF CONTENTS
1. Introduction to the NetVanta 950 IAD Solution ............................................................... 13
Features and Specifications ............................................................................................ 13
Unpack and Inspect the System ...................................................................................... 14
Contents of ADTRAN Shipments ............................................................................ 14
2. Product Overview ................................................................................................................ 15
Reviewing the Chassis Front Panel Design .................................................................... 15
Front Panel LEDs ...................................................................................................... 16
NetVanta Side Panels ...................................................................................................... 16
Side Panel Interfaces ................................................................................................. 18
3. Modules .................................................................................................................................. 19
NetVanta 950 IAD Controller (P/N 1200788L1) ..................................................... 20
NetVanta 950 T1/V.35 Expansion Module (P/N 1200798L1) ................................. 21
NetVanta 900 Series Octal FXS Module (P/N 1200791L1) ..................................... 22
NetVanta 900 Series Octal FXO Module (P/N 1200792L1) .................................... 23
NetVanta 900 Series Octal Ethernet Switch Module (P/N 1200793L1) .................. 24
4. Unit Installation .................................................................................................................... 25
Tools Required ................................................................................................................ 25
Mounting Options ........................................................................................................... 26
Wall mounting the NetVanta 950 ............................................................................. 26
Rack mounting the NetVanta 950 ............................................................................. 27
Installing Modules .......................................................................................................... 28
Grounding Instructions ................................................................................................... 28
Grounding for AC Power .......................................................................................... 29
Grounding for DC Power (Optional Battery Backup) .............................................. 29
Supplying Power to the Unit ........................................................................................... 29
5. Battery Backup Unit ............................................................................................................. 29
Features ..................................................................................................................... 29
Unpack and Inspect ................................................................................................... 30
Safety Notices ........................................................................................................... 30
Installation of the Battery Pack ................................................................................. 31
Maintenance .............................................................................................................. 33
Specifications ............................................................................................................ 33
Appendix A. Pinouts ................................................................................................................ 35
Appendix B. Adtran AOS Supported MIBS ........................................................................... 43

Figures NetVanta 950 IAD Hardware Installation Guide
12 © 2004 ADTRAN, Inc. 61200788L1-34B
Figures
Figure 1. NetVanta 950 Front Panel Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 2. NetVanta 950 Right Side Panel Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Figure 3. NetVanta 950 Left Side Panel Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Figure 4. Voice Connector Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 5. NetVanta 950 Controller Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Figure 6. NetVanta 950 T1/V.35 Expansion Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 7. NetVanta 900 Series Octal FXS Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 8. NetVanta 900 Series Octal FXO Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 9. NetVanta 900 Series Octal Ethernet Switch Module . . . . . . . . . . . . . . . . . . . . . . 24
Figure 10. Wallmounting the NetVanta 950 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Figure 11. Rackmounting the NetVanta 950 IAD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Figure 12. NetVanta 950 Battery Pack Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 13. Battery Pack Mounting Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
List of Tables
Table1. NetVanta 950 Controller Card LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Table 2. Battery Pack Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Table A-1. WAN 0/1, 0/2 Connector Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Table A-2. Alarm Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Table A-3. 10/100BaseT Ethernet Port Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Table A-4. Console Port (DCE) Pinout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Table A-5. T1 1/1 Connector Pinout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Table A-6. V.35 Connector Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Table A-7. 10/100BaseT Ethernet 0/1 Port Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Table A-8. Voice Interface Pinout (Slots 2 - 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Table A-9. Voice Interface Pinout (Slots 5 - 7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Table B-1. MIBs Supported in the AOS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Table B-2. Notes Regarding MIB Exclusions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Table B-3 Traps Supported in the AOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

NetVanta 950 IAD Hardware Installation Guide Introduction to the NetVanta 950 IAD Solution
61200788L1-34B © 2004 ADTRAN, Inc. 13
INTRODUCTION TO THE NETVANTA 950 IAD SOLUTION
The NetVanta 950 is a modular integrated access device (IAD) that incorporates dual T1 network access, a
variety of modules to customize the solution, and an integral router using the ADTRAN Operating System
(AOS).
The NetVanta 950 IAD Family includes the NetVanta 900 Series AC Chassis, AC power supply, system
controller, and various modules for voice and data applications. Currently, the NetVanta 950 IAD Family
offers the Octal FXS and Octal FXO Modules for voice applications, a T1/V.35 Expansion Module for data
applications, and an Octal Ethernet Switch Module for local area network needs.
Features and Specifications
The NetVanta 950 has the following features:
• Dual T1 network access located on the side of the chassis (RJ-45)
• Integrated 10/100BaseT Ethernet port (RJ-48C)
• Full-featured IP router for frame relay or PPP Networks
• Stateful inspection firewall
• User-friendly web GUI and a familiar CLI interface
• SNMP management
• Integrated EIA-232 DCE configuration port located on the system controller module (DB-9)
• LEDs for module status information
• Chassis dimensions: 7.5"H x 10"W x 7"D
• AC power information: 120 VAC, 60 Hz
This hardware installation guide describes the NetVanta 950 unit, details basic functionality, gives
installation instructions, and lists unit specifications. For more information on a specific application, refer
to the quick start documents provided on your Adtran OS Documentation CD. For details on the command
line interface, refer to the AOS Command Reference Guide (also included on your CD).
The NetVanta 950 IAD system is intended to be installed, maintained, and serviced
by qualified personnel only.

Introduction to the NetVanta 950 IAD Solution NetVanta 950 IAD Hardware Installation Guide
14 © 2004 ADTRAN, Inc. 61200788L1-34B
Unpack and Inspect the System
Each NetVanta 950 unit is shipped in its own cardboard shipping carton. Open the carton carefully and
avoid deep penetration into the carton with sharp objects.
After unpacking the unit, inspect it for possible shipping damage. If the equipment has been damaged in
transit, immediately file a claim with the carrier and contact ADTRAN Customer Service (see Product
Warra nty, on page 8).
Contents of ADTRAN Shipments
NetVanta 950 AC System
Shipments of the NetVanta 950 include the following items:
• NetVanta 950 AC Chassis/Power Supply/Controller
• CD documentation, Quick Start Guide, and Wallmount Guide
• Warranty Card
• IEC 3-prong power cord
• Two 15’ RJ-45 cables (3125M008@A)
• Four #8 lug screws for wallmounting
NetVanta 950 T1/V.35 Expansion Module
Shipments of the T1/V.35 Expansion Module include the following items:
• T1/V.35 Expansion Module
• Quick Start Guide
• 15’ straight RJ cable (3125M008@A)
• 15’ crossover RJ-45 cable (3125M010@A)
NetVanta 900 Series Octal FXS Access Module
Shipments of the Octal FXS Access Module include the following items:
• Octal FXS Access Module
• Quick Start Guide
NetVanta 900 Series Octal FXO Access Module
• Octal FXO Access Module
• Quick Start Guide
NetVanta 900 Series Octal Ethernet Switch Access Module
Shipments of the Octal Ethernet Switch Access Module include the following items:
• Octal Ethernet Switch Access Module
• Quick Start Guide
Modules are intended to be serviced by qualified service personnel only.

NetVanta 950 IAD Hardware Installation Guide Product Overview
61200788L1-34B © 2004 ADTRAN, Inc. 15
PRODUCT OVERVIEW
Reviewing the Chassis Front Panel Design
Figure 1 shows the NetVanta 950 front panel.
Figure 1. NetVanta 950 Front Panel Layout
1200792L11200792L1
NetVanta 900 Series
ANLG FXO
1200792L1
TRUNKS

Product Overview NetVanta 950 IAD Hardware Installation Guide
16 © 2004 ADTRAN, Inc. 61200788L1-34B
Front Panel LEDs
Table 2-1 describes the controller card LEDs in order as located from top to bottom.
NetVanta Side Panels
Figure 2 and Figure 3 on page 17 show the NetVanta 950 side panels. All voice connections are provided
through two 50-pin amphenol connectors (located on the right side panel). The left side panel contains the
battery backup connector, the T1 network connections, the alarm contacts, the power connection, and the
ground lug.
Table 2-1. NetVanta 950 Controller Card LEDs
For these
LEDs…
This activity… Indicates that…
SYSTEM Off No power to the unit.
Green (solid) The power is on and the unit is functioning normally.
Red (solid) The boot code could not be booted. It may also mean
battery power is being used.
WAN TI
(0/1 and 0/2) Off The WAN interface is administratively down.
Green (solid) The link is up and everything is normal.
Red (solid) An alarm condition is occurring on the WAN interface.
Yellow (solid) The interface unit is in test.
ETHERNET
0/1
Green (off) The link is down.
Green (solid) The link is up.
Amber (off) No traffic on the link.
Amber (blink) Blinks with traffic on the interface.

NetVanta 950 IAD Hardware Installation Guide Product Overview
61200788L1-34B © 2004 ADTRAN, Inc. 17
Figure 2. NetVanta 950 Right Side Panel Layout
Figure 3. NetVanta 950 Left Side Panel Layout
Voice Ports
(Amphenol)
Power
Connection
Battery
Backup
Connection
Alarm
Contacts
T1
Network
Connections
Ground
Lug

Product Overview NetVanta 950 IAD Hardware Installation Guide
18 © 2004 ADTRAN, Inc. 61200788L1-34B
Side Panel Interfaces
WAN Interfaces
The NetVanta 950 IAD provides two RJ-48C connectors on the left side panel for connection to T1
network services. Status LEDs for the WAN interfaces are integrated on the Controller (see page 16 for
more details on the LEDs). See Table A-1 on page 35 for the WAN interface pinout. The WAN
interface provides the following:
• AMI or B8ZS coding
• Manual line build-out
• D4 or ESF framing
• Test loopbacks with test pattern generation and checking (through the Controller)
Alarm Contacts
This connection alerts the user when an alarm condition exists. The 3-pin, removable terminal block
connects with external wiring. The user should determine whether the external alarm reporting device
uses a normally open (NO) or normally closed (NC) circuit for the alarm.
During an alarm condition, the internal alarm relay shorts NO and COM (the relay is closed) and NC is
open circuited. Alarm conditions include: Power Failure, Battery Backup (requires optional battery
backup), and T1 alarm.
See Table A-2 on page 35 for the Alarm Contact pinout.
Battery Backup Connection
The NetVanta 950 IAD provides a modular plug for connecting to an alternate -48 VDC power supply
(ADTRAN power supply/battery charging unit P/N 1175044L1). Refer to the Battery Backup Unit on
page 29 for more details on this connection.
Voice Connections
The NetVanta 950 IAD provides two 50-pin amphenol connectors for up to 48 tip and ring pairs. Voice
modules installed in slots 2 through 4 are available through the top amphenol connector, and slots 5
through 7 use the bottom amphenol connector. An optional 50-port breakout panel is available (P/N
1200799L48 or 1200799L50). For instructions on mounting the breakout panels, refer to the Breakout
Panel Quick Start Guide, 61200799L48-13. Figure 4 on page 19, Table A-8 on page 38, and Table A-9
on page 40 show the Voice Connection pinouts.

NetVanta 950 IAD Hardware Installation Guide Modules
61200788L1-34B © 2004 ADTRAN, Inc. 19
Figure 4. Voice Connector Pin Assignment
MODULES
The NetVanta 900 Series offers several modules designed to meet a variety of networking requirements.
The modules are of three types: controller, expansion modules, and access modules.
The following modules are available for the NetVanta 950:
• NetVanta 950 IAD Controller (see page 20)
• NetVanta 950 T1/V.35 Expansion Module (see page 21)
• NetVanta 900 Series Octal FXS Access Module (see page 22)
• NetVanta 900 Series Octal FXO Module (see page 23)
• NetVanta 900 Series Octal Ethernet Switch Access Module (see page 24)
This section describes each module, providing individual card specifications and features. Refer to Pin
Assignments on page 35 for pinout information. Installing Modules on page 28 provides information on
module installation.
The NetVanta 950 IAD System is intended to be installed, maintained, and serviced
by qualified personnel only.
261
272
283
294
305
316
327
338
349
3510
3611
3712
3813
3914
4015
4116
4217
4318
4419
4520
4621
4722
4823
4924
5025
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
NC
NC
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
50 PIN AMPH
RECEPTACLE
Slot 2
Slot 3
T
T
R
T
T
R
R
Slot 4
P
P
P
P
Circuit 1
Circuit 2
Circuit 3
Circuit 4
Circuit 5
Circuit 6
Circuit 7
Circuit 8
Circuit 1
Circuit 2
Circuit 3
Circuit 4
Circuit 5
Circuit 6
Circuit 7
Circuit 8
Circuit 1
Circuit 2
Circuit 3
Circuit 4
Circuit 5
Circuit 6
Circuit 7
Circuit 8
R
Slots 2-4
261
272
283
294
305
316
327
338
349
3510
3611
3712
3813
3914
4015
4116
4217
4318
4419
4520
4621
4722
4823
4924
5025
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
R
T
NC
NC
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
P
50 PIN AMPH
RECEPTACLE
Slot 5
Slot 6
T
T
R
T
T
R
R
Slot 7
P
P
P
P
Circuit 1
Circuit 2
Circuit 3
Circuit 4
Circuit 5
Circuit 6
Circuit 7
Circuit 8
Circuit 1
Circuit 2
Circuit 3
Circuit 4
Circuit 5
Circuit 6
Circuit 7
Circuit 8
Circuit 1
Circuit 2
Circuit 3
Circuit 4
Circuit 5
Circuit 6
Circuit 7
Circuit 8
R
Slots 5-7
Top Amphenol Connector Bottom Amphenol Connector

Modules NetVanta 950 IAD Hardware Installation Guide
20 © 2004 ADTRAN, Inc. 61200788L1-34B
NetVanta 950 IAD Controller (P/N 1200788L1)
The NetVanta 950 IAD uses a central controller card to provide configuration for the system using the
AOS. The NetVanta 950 Controller (shown in Figure 5) provides control interfaces for the NetVanta 950
System including a Console port (DB-9) and an Ethernet interface (RJ-48C). Refer to Table A-4 on page
36 for the Console connector pinout, and refer to Table A-3 on page 35 for the Ethernet connector pinout.
A Controller module is required for all NetVanta 950 systems.
Figure 5. NetVanta 950 Controller Module
Features and Specifications
Interfaces
•Console: EIA-232 (DB-9 female) for access to command line
interface and monitoring
•Ethernet:10/100BaseT interface (RJ-48C) for connection to the
local area network
Agency Approvals
• FCC Part 15, Class A
• FCC Part 68
• UL 60950, Third Edition/CSA C22.2, No. 60950
• Industry Canada CS-03
Environmental
• Operating Temperature: 0°C to 50°C
• Storage Temperature: -20°C to 70°C
• Relative Humidity: 95% noncondensing