ADTRAN OC-3 User manual

jobAid
DESCRIPTION
The OC-3 Intermediate Reach (OC-3 SFP) plugs into ADTRAN
OC-3 modules designed to accept Small Form-Factor Pluggables
(SFPs). Installed into an appropriate host module, the OC-3 SFP
provides an OC-3 interface to the supporting system.
NOTE
To ensure compatibility, refer to the documentation provided
with the host module.
The following features are supported on the OC-3 SFP:
SONET OC-3 (155.52 Mb/s) 1310 nm, intermediate-reach (IR-
1), single-mode, 2-fiber operation
15 km maximum optical span
Digital diagnostics available through the menus of the host
module
CAUTION
!
Due to compliance certification requirements, only SFPs supplied
by ADTRAN are to be used with the host module. ADTRAN
cannot certify system integrity with other SFPs.
Operational Specifications
Optical Specifications:
oTransmit level: –15 dBm to –8 dBm
oReceive level: –28 dBm to –8 dBm
oPower penalty: 1 dB
oOptical budget: 12 dB
oOptical connectors: LC
oMaximum optical span: 15 km
oMinimum span attenuation: 0 dB
Extended Environmental Support:
oOperational temperature range: –40°C to +65°C
oStorage temperature range: –40°C to +100°C
oRelative humidity to 95%, noncondensing
INSTALLATION
Before installing the equipment, inspect the OC-3 SFP. If damage
has occurred during shipping, file a claim with the carrier, and
then contact ADTRAN Customer Support. For more information,
refer to the warranty.
ToinstalltheOC‐3SFPintoanappropriatemodule,completethe
followingsteps:
NOTE
Do not remove the protective end cap from the SFP until the fiber
optic cable is ready to be connected.
1. Insert the OC-3 SFP into the SFP cage on the module. Ensur-
ing that the latch handle on the SFP is facing upward, slide
the SFP all the way into the SFP cage until there is an audible
“click”.
NOTE
The latch on the SFP is for removal only. When removing the SFP,
rotate the latch away from the SFP, the SFP should easily slide out
of the cage.
2. Continue the installation and turn-up of the host module
using the instructions in the Job Aid provided with the
module or other system-level documentation available
online at www.adtran.com.
NOTICE
It is recommended that the protective end cap remain on
whenever the transceiver optical fiber connector is not inserted.
PROVISIONING
The OC-3 SFP is not directly provisionable. To provision the OC-3
SFP, access the menu system of the host module. Refer to the
“Provisioning” section of the Job Aid or I&M provided with the
host module for provisioning details.
SAFETY AND REGULATORY COMPLIANCE
CAUTION
C
Electrostatic Discharge (ESD) can damage electronic modules.
When handling modules, wear an antistatic discharge wrist
strap to prevent damage to electronic components. Place
modules in antistatic packing material when transporting or
storing. When working on modules, always place them on an
approved antistatic mat that is electrically grounded.
Per GR-1089-CORE the ADTRAN system that this product is
being deployed in is designed and intended for installation as
part of a Common Bonding Network (CBN). The ADTRAN
system that this product is being deployed in is not designed
nor intended for installation as part of an Isolated Bonding
Network (IBN).
Small Form-Factor Pluggable
OC-3 Intermediate Reach
CLEI: SOOTAE0J_ _
Product P/N: 1184543PG2
Issue Date: July 2012
Document P/N: 61184543PG2-22A

Per GR-1089-CORE Section 9, this product does not have an
internal DC connection between battery return and frame
ground. This product can be installed in a DC-I (isolated) or
DC-C (common) installation. For installations where other
cards or the host system have internal connections between
battery return and frame ground, the system would be
intended for deployment only in a DC-C installation.
The ADTRAN system chassis frame ground terminal must be
connected to an earth ground to ensure that the metal
enclosure of this product is properly grounded via the
backplane connector.
NOTE
The OC-3 port(s) are optical and therefore are not classified as any
type of port as defined in Appendix B of GR-1089-CORE Issue 4.
This product is NRTL Listed to the applicable UL standards. This
product meets or exceeds all the applicable requirements of
NEBS, Telcordia GR-63-CORE, and GR-1089-CORE. This product
is intended for deployment in Central Office type facilities, EEEs,
EECs, and locations where the NEC applies (for example,
Customer Premises). Install this equipment in an ADTRAN
product located in a restricted access location.
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference
2. This device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by ADTRAN
could void the user's authority to operate this equipment.
This product is designed to meet the following environmental
classes:
ETSI EN 300 019-1-1 Classification of environmental conditions;
Storage, Class 1.2
ETSI EN 300 019-1-2 Classification of environmental conditions,
Transportation, Class 2.3
ETSI EN 300 019-1-3 Classification of environmental conditions,
Stationary use at weather-protected locations, Class 3.3
The OC3 IR SFP 1184543PG2 is designed to be deployed in GR-
3108-CORE environmental class 2 as defined in GR-3108-CORE.
The equipment is designed to function without degradation
during exposure to all test severities per Class 3.3.
CAUTION!
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY
HANDLING PRECAUTIONS REQUIRED
For more information, refer to the Installation and Maintenance Guide for the host module,
available online at www.adtran.com.
Warranty: ADTRAN will replace or repair this product within the warranty period if it does not
meet its published specifications or fails while in service. Warranty information can
be found online at www.adtran.com/warranty.
©2012 ADTRAN, Inc. All Rights Reserved.
ADTRAN CUSTOMER CARE:
From within the U.S. 1.800.726.8663
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807
*61184543PG2-22A*