ADTRAN SFP+ 10 Gig XGS-PON N2 OLT User manual

Q
uick Star
t
DESCRIPTION
The 10 Gig XGS-PON Optical Line Termination (OLT) Class N2
Small Form-factor Pluggable (SFP+) is a single-mode fiber SFP+.
The SFP+ provides a single optical interface to a physical
interface, and is intended for use with a 9.953 Gbps Passive
Optical Network (PON) OLT module. The SFP+ provides a 9.953
Gbps XGS-PON interface to the supporting system.
The SFP+ is configured with an L-band 9.953 Gbps downstream
transmitter and a C-band 9.953 Gbps upstream receiver, which
work in a TDM configuration. The SFP+ is designed to support
over distances up to 20 km in the Optical Distribution Network
(ODN). It is FDA 21CFR1040.10 and IEC
60825-1 Class I laser safety compliant and meets the EU RoHS
Directive.
This SFP+ supports the following features:
■ODN Class N2 Transceiver
■Data rate: 9.953 Gbps
■Optical Receive Wavelength: 1270 nm
■Optical Transmit Wavelength: 1577 nm
■Optical distance: 20 km maximum
■Hot Pluggable
Applications:
■XGS-PON Access networks
■Fiber to the Premises (FTTP)
■Fiber to the Building (FTTB)
■Fiber to the Curb (FTTC)
Due to compliance certification requirements, use only pluggable
optics supplied by ADTRAN. ADTRAN cannot certify system
integrity with other pluggable optics.
INSTALLATION
Before installing the equipment, inspect the SFP+. If damage has
occurred during shipping, file a claim with the carrier, and then
contact ADTRAN Customer Support. For more information, refer
to the warranty.
Installation Steps
To install the SFP+ into an appropriate device, complete the
following steps:
g NOTE
Do not remove the protective dust cover from the SFP+ until the
fiber optic cable is ready to be connected.
1. Insert the SFP+ into the SFP+ cage on the module. Ensuring
that the latch on the SFP+ is facing upward, slide the SFP+
all the way into the SFP+ cage until there is an audible
“click”.
g NOTE
The latch on the SFP+ is for removal only. When removing the
SFP+, rotate the latch away from the SFP+. It should easily slide
out of the cage.
w NOTICE
Do not remove the protective dust cover until the optical fiber
connection is made. Ensure that you keep the protective dust
cover on whenever the transceiver optical fiber connector is not
inserted.
2. Continue the installation and turn-up of the host module
using the instructions in the Job Aid or Quick Start provided
with the module or other system-level documentation
available online at www.adtran.com.
ADTRAN Pluggable Optics
SFP+
10 Gig XGS-PON N2 OLT
January 2020
61442544F2-13A
P/N: 1442544F2

261442544F2-13A
SAFETY AND REGULATORY
ENGLISH
f WARNING!
Read all warnings, cautions, notes, and installation instructions
before installing or servicing this equipment.
CCAUTION!
This product is a Class 1 Laser module that complies with FDA 21
CFR 1040.10, 1040.11 and IEC 60825-1.
f CAUTION!
■Electrostatic Discharge (ESD) can damage electronic
modules. When handling modules, wear an antistatic
discharge wrist strap to prevent damage to electronic
components. Place modules in antistatic packing material
when transporting or storing. When working on modules,
always place them on an approved antistatic mat that is
electrically grounded.
■This product and the host system are designed and intended
for installation as part of either a Common Bonding Network
(CBN) or Isolated Bonding Network (IBN).
■This product’s outer case is “electrically isolated” from other
circuits, as a result, this product can be used in systems that
are installed either in a DC-I (isolated) or DC-C (common)
configuration. For Systems where other installed modules or
the host system itself have internal connections between
battery return and frame ground, the system can only be
deployed in a DC-C configuration.
■If the host system has a protective earth (PE) terminal, the PE
terminal of the host system must be connected to protective
earth (PE) to ensure that the exposed metal (i.e., front panels,
optical modules) on the product is properly grounded.
SPECIFICATIONS
General
■Module Type: SFP+
■Media Type: Fiber
♦Single-Mode
♦Single Fiber
■Signal Data Rate:
♦Maximum: 9.953 Gbps
■Distance: 20 km
■Not Compatible with SFP+ MSA
■Applications: XGS-PON, FTTP, FTTB, FTTC
■Optical Connector: SC
Optical
■Transmitter
♦Laser Diode Type: EML
♦Transmit Wavelength: 1577 nm
♦Tx Power: +4.0 dBm to +7.0 dBm
♦Spectral Width: 1 nm
♦SMSR: 30.0 dBm
♦Extinction Ratio: 8.2 dB
■Receiver
♦Type: APD
♦Central Wavelength: 1270 nm
♦Receiver Sensitivity: –28.0 dBm
♦Receiver Overload: –7.0 dBm
Environmental
■Protected Equipment Severe Environment (Outdoor)
♦System Ambient Operational Temperature Range:
–40°C to +70°C
♦Storage Temperature Range: –40°C to +85°C
♦Relative Humidity 5% to 95%, non-condensing

61442544F2-13A 3
g NOTE
■This product is designed to be deployed in GR-3108-CORE
environmental Class 1, 2, or 3.
■This product is NRTL Listed to the applicable UL Standards.
The product is designed to meet the applicable requirements
of Telcordia GR-63-CORE, GR-1089-CORE and GR-3108-
CORE. This product has also been evaluated to applicable
international standards and meets the requirements for CE
marking.
■This product is intended for deployment in locations such as
Central Offices and outside plant cabinets. This product is to
be installed and serviced by trained and qualified Service
personnel only.
■This device complies with Part 15 of the FCC rules. Operation
is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
■Changes or modifications not expressly approved by ADTRAN
will void the warranty.
■This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction
manual, may cause harmful inference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the
user will be required to correct the interference at the user’s
own expense.
■CAN ICES-3(A)/NMB-3(A)
■This product is designed to meet the following environmental
classes.
♦ETSI EN 300 019-1-1 “Classification of environmental
conditions; Storage,” Class 1.2
♦ETSI EN 300 019-1-2 “Classification of environmental
conditions, Transportation,” Class 2.3
♦ETSI EN 300 019-1-3 “Classification of environmental
conditions, Stationary use at weather protected locations,”
Class 3.4
■This product is designed to function without degradation during
exposure to all test severities per Class 3.4.
■This product meets EU RoHS Directive. Refer to
www.adtran.com for further information on RoHS/WEEE.
FRANÇAIS
f AVERTISSMENT!
Lisez toutes les mentions de danger et de prudence et les
remarques, ainsi que la notice d'installation, avant d'effectuer
l'installation ou l'entretien de cet équipement.
C ATTENTION!
Ce produit est un laser de classe 1 conforme à la norme FDA 21
CFR 1040.10 et 1040.11 et IEC 60825-1.
f ATTENTION!
■L'ESD (décharge électrostatique) peut endommager les
modules électroniques. Lors de la manipulation des modules,
portez un bracelet de décharge antistatique pour éviter
d’endommager les composants électroniques. Placez les
modules dans un emballage antistatique lors du transport ou
du stockage. Lorsque vous travaillez sur les modules, placez-
les toujours sur un tapis antistatique certifié muni d’un
branchement de mise à la terre.
■Ce produit et système hôte sont conçus et destinés à être
installés dans le cadre soit d'un réseau commun Bonding
(CBN) ou isolé Réseau Bonding (IBN).
■Si le système hôte est doté d'une borne de mise à la terre de
protection (PE), la borne PE du système hôte doit être
connectée à la mise à terre de protection (PE), afin d'assurer
que les parties métaliques à découvert (panneaux frontaux,
modules optiques) du produit soient correctement mis à terre.
g REMARQUE
Ce produit est conforme à la directive européenne RoHS.
Reportez-vous à www.adtran.com pour de plus amples rensei-
gnements sur RoHS.

CAUTION!
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY
HANDLING PRECAUTIONS REQUIRED
Warranty: ADTRAN will replace or repair this product within the warranty period if it does not
meet its published specifications or fails while in service. Warranty information can be
found online at www.adtran.com/warranty.
Trademarks: Brand names and product names included in this document are trademarks,
registered trademarks, or trade names of their respective holders.
Copyright © 2020 ADTRAN, Inc. All Rights Reserved.
ADTRAN CUSTOMER CARE:
From within the U.S. 1.888.423.8726
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807
*61442544F2-13A*
DEUTSCH
f WARNUNG!
Lesen Sie alle Warnungen, Gefahrenhinweise, Anmerkungen und
Installationsanweisungen bevor Sie dieses Gerät installieren oder
warten.
C VORSICHT!
Dieses Produkt ist ein Klasse 1 Laser, die mit FDA 21 CFR
1040.10 und 1040.11 und IEC 60825-1 entspricht.
f VORSICHT!
■Elektrostatische Entladung können elektronische Module
beschädigen. Tragen Sie beim Umgang mit Modulen ein
Erdungsarmband, um Schäden an den elektronischen
Komponenten zu vermeiden. Transportieren oder lagern Sie
Module in antistatischem Verpackungsmaterial. Bei der Arbeit
an den Modulen, achten Sie darauf, diese stets auf
antistatische, elektrisch geerdete Matten zu legen.
■Dieses Produkt und Host-System sind so konzipiert und für die
Installation als Teil entweder eine gemeinsame Bonding
Network (CBN) oder isoliert Bonding Network (IBN)
vorgesehen.
■Falls das Host-System über einen Schutzleiteranschluss (PE)
verfügt, muss der PE-Anschluss des Host-Systems mit dem
Schutzleiteranschluss (PE) verbunden werden, um
sicherzustellen, dass das freiliegende Metall (d. h.
Frontblenden, Optikmodule) am Produkt ordnungsgemäß
geerdet ist.
g HINWEIS
Dieses Produkt erfüllt die EU RoHS Richtlinie. Bitte besuchen Sie
www.adtran.com für ausführlichere Informationen zu
RoHS/WEEE.
Documentation for ADTRAN Network Solutions products is available for
viewing and download directly from the ADTRAN Support Community
website.
Go to: https://supportforums.adtran.com/welcome
Registration is required.
ADTRAN offers training courses on our products, including customized
training and courses taught at our facilities or at customer sites.
For inquiries, go to: http://adtran.com/training
The following online documents and resources provide additional information for this product:
ADTRAN Pluggable Optics Compatibility Matrix (online tool, go to: http://www.adtran.com/
pluggableoptics)