ADTRAN QSFP+ User manual

Q
uic
k
Start
DESCRIPTION
The QSFP+ 4x10GBASE-LR4 MPO 10 km (QSFP+ LR4) trans-
ceiver is designed for use in 40 Gbps links over single mode fiber.
The QSFP+ LR4 integrates four independent transmit and receive
channels. Each channel operates at 10.3125 Gbps. The module
can operate at 40 Gbps up to 10 km using 9/124 μm single mode
optical fiber (SMF). The QSFP+ LR4 is complaint with QSFP+
MSA and IEEE 802.3ba 40GBase-LR4.The QSFP+ LR4 has an
MPO (MTP) connector and requires an optical fiber ribbon cable
with MPO (MTP) connectors.
INSTALLATION
To install the QSFP+ LR4 into an applicable module, complete the
following steps:
1. Inspect the QSFP+ LR4. If damaged, file a claim with the
carrier and then contact ADTRAN Customer Service.
2. Do not remove the protective end cap from the QSFP until
the fiber optic cable is ready to be connected.
3. Insert the QSFP+ LR4 into the QSFP cage on the module.
Ensure the manufacturer’s label on the QSFP is facing
upward for correct installation.
4. Slide the QSFP+ LR4 all the way into the receptacle until
there is an audible “click.”
f
CAUTION!
Due to compliance certification requirements, use only QSFPs
supplied by ADTRAN. ADTRAN cannot certify system integrity
with other QSFPs.
w NOTICE
The loop on the QSFP is used to remove the QSFP from the cage
on the circuit card.
SPECIFICATIONS
General
■Module type: QSFP+
■Fiber/Copper: Fiber
■Lanes/Channels: 4 Transmit and 4 Receive
■Signal data rate: Up to 10.3 Gbps per channel
■Optical Connector: MPO/MTP
■Applications: 40GBASE-LR4 Ethernet, Data Center
■Distance: 10 km over single-mode fiber
Optical
■Transmitter
♦Laser Diode Type: DFB Array (4 parallel channels)
♦Tx Wavelengths: 1310 nm (each channel)
♦Tx Output Optical Power: –6.0 to +1.5 dBm at each lane
♦Extinction Ratio: 3.5 dB
■Receiver
♦Rx Type: PIN Array
♦Rx Wavelengths: 1310 nm (each channel)
♦Receive Overload: +2.3 dBm at each lane
♦Receive Sensitivity: –12.6 dBm at each lane
Environmental
■Controlled Protected Equipment (Inside)
♦Operational temperature range: –5°C to +55°C
♦Storage temperature range: –40°C to +85°C
♦Relative humidity 5 to 85%, non-condensing
ADTRAN Pluggable Optics
QSFP+
QSFP+ 4x10GBASE-LR4 MPO 10 km
July 2018
61445502F4C-13A
P/N: 1445502F4C

2 61445502F4C-13A
Changes or modifications not expressly approved by ADTRAN
could void the user's authority to operate this equipment.This
product meets EU RoHS. Refer to www.adtran.com for further
information on RoHS/WEEE.
FRANÇAIS
f AVERTISSMENT!
Lisez tous les avertissements et mises en garde avant l’instal-
lation de cet équipement ou la réalisation de toute opération de
maintenance.
C
ATTENTION!
Ce produit contient ou utilise un module Laser de classe 1 qui est
conforme avec la FDA 21 CFR 1040.10, 1040.11 et IEC 60825-1.
Pour le maintien de la conformité avec les normes ci-dessus,
seulement approuvé classe 1 modules laser d'un ADTRAN
approuvés liste des fournisseurs (situé sur le site ADTRAN) doit
être installé dans ce produit. ADTRAN ne peut certifier l'intégrité
du système avec d'autres modules laser.
f ATTENTION!
■L'ESD (décharge électrostatique) peut endommager les
modules électroniques. Lors de la manipulation des modules,
portez un bracelet de décharge antistatique pour éviter
d’endommager les composants électroniques. Placez les
modules dans un emballage antistatique lors du transport ou
du stockage. Lorsque vous travaillez sur les modules, placez-
les toujours sur un tapis antistatique certifié muni d’un
branchement de mise à la terre.
■Ce système est conçu et prévu pour une installation intégrée
à un réseau de masse maillé. Ce système n’est pas conçu ni
prévu pour une installation intégrée à un réseau de masse
isolé (IBN).
■Ce produit ne dispose pas d’une connexion c.c. interne entre
le courant de retour de la batterie et la masse du châssis. Ce
produit peut être installé en configuration c.c.-I (isolé) ou c.c.-
C (commun). Pour les installations où d'autres cartes ou le
système hôte ont des connexions internes entre le retour de la
batterie et la masse du châssis, le système ne peut être
déployé que dans une configuration c.c.-C.
■La borne de terre de châssis doit être connecté à une prise de
terre pour assurer que le métal exposé (tels que les panneaux
avant, des modules SFP / XFP) sur le produit est correctement
mis à la terre via le connecteur de fond de panier.
g REMARQUE
Ce produit est conforme à la directive européenne RoHS.
Reportez-vous à www.adtran.com pour de plus amples rensei-
gnements sur RoHS.
SAFETY AND REGULATORY
f WARNING!
Read all warnings and cautions before installing or servicing this
equipment.
CCAUTION!
This product contains or uses a Class 1 Laser module that
complies with FDA 21 CFR 1040.10, 1040.11 and IEC 60825-1.
For continued compliance with the above standards, only
approved Class 1 laser modules from an ADTRAN approved
vendor list (located on the ADTRAN website) should be installed
in this product. ADTRAN cannot certify system integrity with other
laser modules.
f
CAUTION!
■Electrostatic Discharge (ESD) can damage electronic
modules. When handling modules, wear an antistatic
discharge wrist strap to prevent damage to electronic
components. Place modules in antistatic packing material
when transporting or storing. When working on modules,
always place them on an approved antistatic mat that is
electrically grounded.
■This system is designed and intended for installation as part of
a Common Bonding Network (CBN). This system is not
designed nor intended for installation as part of an Isolated
Bonding Network (IBN).
■This product does not have an internal DC connection
between battery return and frame ground. This product can be
installed in a DC-I (isolated) or DC-C (common) configuration.
For installations where other cards or the host system have
internal connections between battery return and frame ground,
the system would be intended for deployment only in a DC-C
configuration.
■The chassis frame ground terminal must be connected to an
earth ground to ensure that the exposed metal (i.e., front
panels, SFP/XFP modules) on the product is properly
grounded via the backplane connector.
■This product is intended for deployment in Central Office type
facilities, EEEs, EECs, and locations where the NEC applies.
g NOTE
■Install this product in a Restricted Access Location. This
product is intended to be installed and serviced by qualified
Service Personnel only.
■This product is designed to be deployed in GR-3108-CORE
environmental Class 1.
■This product is NRTL Listed to the applicable UL Standards.
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.

61445502F4C-13A 3
DEUTSCH
f
WARNUNG!
Lesen Sie sich alle Warn- und Sicherheitshinweise durch, bevor
Sie das Gerät installieren oder Servicehandlungen vornehmen.
C
VORSICHT!
DasProdukt enthält oder verwendet Klasse 1 Laser-Module, die
60825-1 mit FDA 21 CFR 1040.10, 1040.11 und IEC erfüllen.
Damit die obigen Richtlinien auch in Zukunft eingehalten werden
können, dürfen ausschließlich Klasse 1 Lasermodule von einem
von ADTRAN zugelassenen Anbieter in dem Produkt installiert
werden (siehe Website von ADTRAN). ADTRAN garantiert nicht
für die Systemintegrität bei anderen Lasermodulen.
f
VORSICHT!
■Elektrostatische Entladung können elektronische Module
beschädigen. Tragen Sie beim Umgang mit Modulen ein
Erdungsarmband, um Schäden an den elektronischen
Komponenten zu vermeiden. Transportieren oder lagern Sie
Module in antistatischem Verpackungsmaterial. Bei der Arbeit
an den Modulen, achten Sie darauf, diese stets auf
antistatische, elektrisch geerdete Matten zu legen.
■Das System ist entwickelt und vorgesehen für die Installation
als Teil einer gemeinsamen Potentialausgleichsanlage. Das
System ist nicht zur Installation als Teil einer isolierten
Potentialausgleichsanlage vorgesehen.
■Dieses Produkt hat keinen internen Gleichstromanschluss
zwischen Batterierücknahme und Gehäusemasse. Dieses
Produkt kann in einer DC-I (isoliert) oder DC-C (emeinsam)
Konfiguration installiert werden. Bei Installationen, bei denen
andere Karten oder das Host -System interne Verbindungen
zwischen derBatterierückleitung und der Gehäusemasse
haben, würde das System nur für den Einsatz in einer DC-C-
Konfiguration eingesetzt werden.
■Der Fahrgestellrahmen Erdanschluß muß zu einer Erde
verbunden werden, um sicherzustellen, dass das freiliegende
Metall (dh Frontplatten, SFP / XFP-Module) auf dem Produkt
richtig über den Backplane-Anschluss geerdet ist.
g
HINWEIS
Dieses Produkt erfüllt die EU RoHS Richtlinie. Bitte besuchen Sie
www.adtran.com für ausführlichere Informationen zu RoHS/
WEEE.

CAUTION!
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY
HANDLING PRECAUTIONS REQUIRED
Warranty: ADTRAN will replace or repair this product within the warranty period if it does not
meet its published specifications or fails while in service. Warranty information can be
found online at www.adtran.com/warranty.
Trademarks: Brand names and product names included in this document are trademarks,
registered trademarks, or trade names of their respective holders.
©2018 ADTRAN, Inc. All Rights Reserved.
ADTRAN CUSTOMER CARE:
From within the U.S. 1.888.423.8726
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807
*61445502F4C-13A*
Documentation for ADTRAN Network Solutions products is available for
viewing and download directly from the ADTRAN Support Community
website.
Go to: https://supportforums.adtran.com/welcome
Registration is required.
ADTRAN offers training courses on our products, including customized
training and courses taught at our facilities or at customer sites.
For inquiries, go to: http://adtran.com/training
The following online documents and resources provide additional information for this product:
ADTRAN Pluggable Optics Compatibility Matrix (online tool, go to: http://www.adtran.com/
pluggableoptics)