ADTRAN QSFP28 CWDM4 User manual

Q
uic
k
Start
DESCRIPTION
The QSFP28 CWDM4 transceiver is used in 100 Gbps links over
single mode fiber. The QSFP28 integrates four channel CWDM
DFB lasers and multiplexes them into a single channel for 100
Gbps optical transmission.
The receiving side of the module de-multiplexes the 100 Gbps
optical signal into four CWDM channels. Each channel operates
at 25 Gbps and the module is able to operate at 100 Gbps up to 2
km using 9/125 μm Single Mode Fiber (SMF).
The QSFP28 is compliant with 100G and IEEE 802.3ba
standards.
INSTALLATION
Before installation, inspect the QSFP28. If damage has occurred
during shipping, file a claim with the carrier, and then contact
ADTRAN Customer Support. For more information, refer to
“Warranty”.
Installation Guidelines
The following are guidelines for this installation.
■The latch on the QSFP28 is for removal only. When removing
the QSFP28, rotate the latch away from the QSFP28. The
QSFP28 should slide easily out of the cage.
Installation Steps
To install the QSFP28, complete the following steps:
1. Insert the QSFP28 into the QSFP28 cage on the circuit
board of the host module with the latch handle facing out-
ward. Slide the QSFP28 all the way into the cage.
2. Exert adequate pressure to ensure the QSFP28 is
completely seated in the QSFP28 cage.
3. Do not remove the protective dust cover until the optical fiber
connection is made.
4. Continue the installation and turn-up of the host module.
SPECIFICATIONS
■General
♦Module type: QSFP28
♦Fiber/Copper: SMF
♦Lanes/Channels: 4 Transmit and 4 Receive
♦Signal data rate: Up to 25.78 Gbps per channel
♦Optical Connector: LC
♦Applications: 100G CWDM4
♦Distance: 2 km
■Optical
Transmitter
♦Laser Diode Type: CWDM DML
♦Tx Wavelengths:
●Lane -1: 1264.5 to 1277.5 nm (Typical: 1271 nm)
●Lane -2: 1284.5 to 1297.5 nm (Typical: 1291 nm)
●Lane -3: 1304.5 to 1317.5 nm (Typical: 1311 nm)
●Lane -4: 1324.5 to 1337.5 nm (Typical: 1331 nm)
♦Tx Output optical power: –6.5 dBm to +2.5 dBm per each
Lane
♦Extinction Ratio: 3.5 dB
♦Dispersion Penalty: 3 dB per Lane
Receiver
♦Rx Type: PIN Array
♦Rx wavelengths:
●Lane -1: 1264.5 to 1277.5 nm (Typical: 1271 nm)
●Lane -2: 1284.5 to 1297.5 nm (Typical: 1291 nm)
●Lane -3: 1304.5 to 1317.5 nm (Typical: 1311 nm)
●Lane -4: 1324.5 to 1337.5 nm (Typical: 1331 nm)
♦Receive Overload: 2.5 dBm per Lane
♦Receiver Sensitivity: –10 dBm per Lane
■Environmental
♦Controlled Protected Equipment Environment (Inside)
♦Operational temperature range: –5°C to +55°C
♦Storage temperature range: –40°C to +85°C
♦Relative humidity: 5 to 85%
ADTRAN Pluggable Optics
QSFP28
100G CWDM4 2KM
December 2018
61445512F1C-13B
P/N:1445512F1C

2 61445512F1C-13B
gNOTE
■This product is NRTL Listed to the applicable UL Standards.
■The product is designed to meet the applicable requirements
of Telcordia GR-63-CORE and GR-1089-CORE.
■This product has been evaluated to international safety
standards EN 60950-1, AS/NZS 60950.1, and IEC 60950-1.
■This product meets the requirements for CE marking under the
EMC Directive and Low Voltage Directive. Standards used to
demonstrate Compliance are EN 300 386 and EN 60950.
■This device complies with Part 15 of the FCC rules. Operation
is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by
ADTRAN could void the user's authority to operate this
equipment.
■This product is designed to meet the following environmental
classes:
♦ETSI EN 300 019-2-1 “Classification of environmental condi-
tions;Storage Class” 1.2
♦ETSI EN 300 019-2-2 “Classification of environmental condi-
tions,Transportation”, Class 2.3
♦ETSI EN 300 019-2-3 “Classification of environmental condi-
tions, Stationary use at weather protected locations”, Class
3.1E
■This product is designed to function without degradation during
exposure to all test severities per Class 3.3 of ETSI EN 300
019-2-3.
■This product is designed to be deployed in GR-3108-CORE
environmental class 1 environments.
■This product meets EU RoHS Directive. Refer to
www.adtran.com for further information on RoHS/WEEE.
SAFETY AND REGULATORY
ENGLISH
fWARNING!
Read all warnings and cautions before installing or servicing this
equipment.
CCAUTION!
This product contains or uses a Class 1 Laser module that
complies with FDA 21 CFR 1040.10, 1040.11 and IEC 60825-1.
For continued compliance with the above standards, only
approved Class 1 laser modules from an ADTRAN approved
vendor list (located on the ADTRAN website) should be installed
in this product. ADTRAN cannot certify system integrity with other
laser modules.
f
CAUTION!
■Electrostatic Discharge (ESD) can damage electronic
modules. When handling modules, wear an antistatic
discharge wrist strap to prevent damage to electronic
components. Place modules in antistatic packing material
when transporting or storing. When working on modules,
always place them on an approved antistatic mat that is
electrically grounded.
■This system is designed and intended for installation as part of
a Common Bonding Network (CBN). This system is not
designed nor intended for installation as part of an Isolated
Bonding Network (IBN).
■This product does not have an internal DC connection
between battery return and frame ground. This product can be
installed in a DC-I (isolated) or DC-C (common) configuration.
For installations where other cards or the host system have
internal connections between battery return and frame ground,
the system would be intended for deployment only in a DC-C
configuration.
■The chassis frame ground terminal must be connected to an
earth ground to ensure that the exposed metal (for example,
front panels, QSFP28/XFP modules) on the product is properly
grounded via the backplane connector.
■This product is intended for deployment in Central Office type
facilities, EEEs, EECs, and locations where the NEC applies
(i.e., Customer Premises).

61445512F1C-13B 3
FRANÇAIS
fAVERTISSMENT!
Lisez tous les avertissements et mises en garde avant l’instal-
lation de cet équipement ou la réalisation de toute opération de
maintenance.
C
ATTENTION!
Ce produit contient ou utilise un module Laser de classe 1 qui est
conforme avec la FDA 21 CFR 1040.10, 1040.11 et IEC 60825-1.
Pour le maintien de la conformité avec les normes ci-dessus,
seulement approuvé classe 1 modules laser d'un ADTRAN
approuvés liste des fournisseurs (situé sur le site ADTRAN) doit
être installé dans ce produit. ADTRAN ne peut certifier l'intégrité
du système avec d'autres modules laser.
fATTENTION!
■L'ESD (décharge électrostatique) peut endommager les
modules électroniques. Lors de la manipulation des modules,
portez un bracelet de décharge antistatique pour éviter
d’endommager les composants électroniques. Placez les
modules dans un emballage antistatique lors du transport ou
du stockage. Lorsque vous travaillez sur les modules, placez-
les toujours sur un tapis antistatique certifié muni d’un
branchement de mise à la terre.
■Ce système est conçu et prévu pour une installation intégrée
à un réseau de masse maillé. Ce système n’est pas conçu ni
prévu pour une installation intégrée à un réseau de masse
isolé (IBN).
■Ce produit ne dispose pas d’une connexion c.c. interne entre
le courant de retour de la batterie et la masse du châssis. Ce
produit peut être installé en configuration c.c.-I (isolé) ou c.c.-
C (commun). Pour les installations où d'autres cartes ou le
système hôte ont des connexions internes entre le retour de la
batterie et la masse du châssis, le système ne peut être
déployé que dans une configuration c.c.-C.
■La borne de terre de châssis doit être connecté à une prise de
terre pour assurer que le métal exposé (tels que les panneaux
avant, des modules QSFP28 / XFP) sur le produit est
correctement mis à la terre via le connecteur de fond de
panier.
gREMARQUE
Ce produit est conforme à la directive européenne RoHS.
Reportez-vous à www.adtran.com pour de plus amples rensei-
gnements sur RoHS
DEUTSCH
f
WARNUNG!
Lesen Sie sich alle Warn- und Sicherheitshinweise durch, bevor
Sie das Gerät installieren oder Servicehandlungen vornehmen.
C
VORSICHT!
DasProdukt enthält oder verwendet Klasse 1 Laser-Module, die
60825-1 mit FDA 21 CFR 1040.10, 1040.11 und IEC erfüllen.
Damit die obigen Richtlinien auch in Zukunft eingehalten werden
können, dürfen ausschließlich Klasse 1 Lasermodule von einem
von ADTRAN zugelassenen Anbieter in dem Produkt installiert
werden (siehe Website von ADTRAN). ADTRAN garantiert nicht
für die Systemintegrität bei anderen Lasermodulen.
f
VORSICHT!
■Elektrostatische Entladung können elektronische Module
beschädigen. Tragen Sie beim Umgang mit Modulen ein
Erdungsarmband, um Schäden an den elektronischen
Komponenten zu vermeiden. Transportieren oder lagern Sie
Module in antistatischem Verpackungsmaterial. Bei der Arbeit
an den Modulen, achten Sie darauf, diese stets auf
antistatische, elektrisch geerdete Matten zu legen.
■Das System ist entwickelt und vorgesehen für die Installation
als Teil einer gemeinsamen Potentialausgleichsanlage. Das
System ist nicht zur Installation als Teil einer isolierten
Potentialausgleichsanlage vorgesehen.
■Dieses Produkt hat keinen internen Gleichstromanschluss
zwischen Batterierücknahme und Gehäusemasse. Dieses
Produkt kann in einer DC-I (isoliert) oder DC-C (emeinsam)
Konfiguration installiert werden. Bei Installationen, bei denen
andere Karten oder das Host -System interne Verbindungen
zwischen derBatterierückleitung und der Gehäusemasse
haben, würde das System nur für den Einsatz in einer DC-C-
Konfiguration eingesetzt werden.
■Der Fahrgestellrahmen Erdanschluß muß zu einer Erde
verbunden werden, um sicherzustellen, dass das freiliegende
Metall (dh Frontplatten, QSFP28 / XFP-Module) auf dem
Produkt richtig über den Backplane-Anschluss geerdet ist.
g
HINWEIS
Dieses Produkt erfüllt die EU RoHS Richtlinie. Bitte besuchen Sie
www.adtran.com für ausführlichere Informationen zu RoHS/
WEEE.

CAUTION!
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY
HANDLING PRECAUTIONS REQUIRED
Warranty: ADTRAN will replace or repair this product within the warranty period if it does not
meet its published specifications or fails while in service. Warranty information can be
found online at www.adtran.com/warranty.
Trademarks: Brand names and product names included in this document are trademarks,
registered trademarks, or trade names of their respective holders.
©2018 ADTRAN, Inc. All Rights Reserved.
ADTRAN CUSTOMER CARE:
From within the U.S. 1.888.423.8726
From outside the U.S. +1 256.963.8716
PRICING AND AVAILABILITY 1.800.827.0807
*61445512F1C-13B*
Documentation for ADTRAN Network Solutions products is available for
viewing and download directly from the ADTRAN Support Community
website.
Go to: https://supportforums.adtran.com/welcome
Registration is required.
ADTRAN offers training courses on our products, including customized
training and courses taught at our facilities or at customer sites.
For inquiries, go to: http://adtran.com/training
The following online documents and resources provide additional information for this product:
ADTRAN Pluggable Optics Compatibility Matrix (online tool, go to: http://www.adtran.com/
pluggableoptics)