ADTRAN 1442140G2 User manual

DESCRIPTION
The Small Form-Factor Pluggable (SFP) Gigabit
Ethernet, Single-Fiber is a bidirectional SFP that
plugs into an Optical Network Unit (ONU) designed to
accept SFPs. The SFP provides a single optical
interface to the GigE physical interface. Installed into
an appropriate ONU, the SFP provides a Gigabit
Ethernet interface to the supporting system.
NOTE
To ensure compatibility, refer to the documentation
provided with the ONU.
In a deployment consisting of an ONU with a
1442140G2 SFP installed; the Optical Loop
Termination (OLT) should have a complementary
1442140G1 SFP installed.
The following features are supported on the SFP:
♦1000Base-LX 1310 nm Transmitter
♦1000Base-LX 1490 nm Receiver
♦Optical distance: 40 km maximum
Due to compliance certification requirements, only
SFPs supplied by ADTRAN should be used. ADTRAN
cannot certify system integrity with other SFPs.
OLT
1442140G1 1442140G2
ONU
Rx: 1310 nm
Tx: 1490 nm
Rx: 1490 nm
Tx: 1310 nm
Small Form-Factor Pluggable
1310 nm TX / 1490 nm RX, 40 km
Operational Specifications
♦Optical Specifications:
◊Transmit wavelength: 1310 nm
◊Receive wavelength: 1490 nm
◊Optical transmit level: –2 dBm to +3 dBm
◊Optical receive level: –23 dBm to –3 dBm
◊Optical distance: 40 km
◊Optical connectors: LC
♦Extended Environmental Support:
◊Operational temperature range: –40°C to +70°C
◊Storage temperature range: –40°C to +85°C
◊Relative humidity to 95%, noncondensing
INSTALLATION
Prior to installation, inspect the SFP. If damage has
occured during shipping, file a claim with the carrier,
and then contact ADTRAN Customer Support. For
more information, refer to “Warranty”.
To install the SFP into an appropriate module,
complete the following steps:
1. Insert the SFP into the SFP cage on the circuit
board of the host module with the latch handle
facing outward. Slide the SFP all the way into the
cage.
NOTE
The latch on the SFP is for removal only. When
removing the SFP, rotate the latch away from the
SFP, the SFP should slide easily out of the cage.
2. Exert adequate pressure to ensure the SFP is
completely seated in the SFP cage.
3. Do not remove the connector plug until the
optical fiber connection is made.
It is recommended that the connector plug remain on
whenever the transciever optical fiber connector is
not inserted.
4. Continue the installation and turn-up of the host
module using the instructions in the Job Aid
provided with the module, or using the
Installation and Maintenance Practice (I&M)
available online at www.adtran.com.
CLEI: VAUIAMBP_ _
Product P/N: 1442140G2
Issue Date: 0812
Document P/N: 61442140G2-22B

C A U T I O N
C A U T I O N
!
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY.
HANDLING PRECAUTIONS REQUIRED.
Warranty: ADTRAN will replace or repair this product within the warranty period if it does not
meet its published specifications or fails while in service. Warranty information can
be found online at www.adtran.com/warranty.
©2008 ADTRAN, Inc. All Rights Reserved.
PRICING AND AVAILABILITY 800.827.0807
TECHNICAL SUPPORT 800.726.8663
RETURN FOR REPAIR 256.963.8722
*61442140G2-22B*
COMPLIANCE
Electrostatic Discharge (ESD) can damage electronic
modules. When handling modules, wear an antistatic
discharge wrist strap to prevent damage to electronic
components. Place modules in antistatic packing
material when transporting or storing. When working
on modules, always place them on an approved
antistatic mat that is electrically grounded.
The SFP is NRTL Listed to the applicable UL
standards. The SFP meets or exceeds all the appli-
cable requirements of NEBS, Telcordia GR-63-CORE,
and GR-1089-CORE. The SFP is intended for
deployment in Central Office type facilities, EEEs,
EECs, and locations where the NEC applies (for
example, Customer Premises) and is intended to be
installed by trained service personnel. Install the SFP
in an ADTRAN product located in a restricted access
location.
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference
2. This device must accept any interference
received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by
ADTRAN could void the user's authority to operate
this equipment.
♦ Per GR-1089-CORE the ADTRAN system that the
SFP is being deployed in is designed and intended
for installation as part of a Common Bonding
Network (CBN). The ADTRAN system that the SFP
is being deployed in is not designed nor intended
for installation as part of an Isolated Bonding
Network (IBN).
♦ Per GR-1089-CORE Section 9, the SFP does not
have an internal DC connection between battery
return and frame ground. The SFP can be installed
in a DC-I (isolated) or DC-C (common) installation.
For installations where other cards or the host
system have internal connections between battery
return and frame ground, the system would be
intended for deployment only in a DC-C
installation.
♦ The ADTRAN system chassis frame ground
terminal must be connected to an earth ground to
ensure that the metal enclosure of the SFP is
properly grounded via the backplane connector.
NOTE
The Gigabit Ethernet port(s) are optical and therefore
are not classified as any type of port as defined in
Appendix B of GR-1089-CORE Issue 4.
The SFP is designed to meet the following environ-
mental classes:
♦ETSI EN 300 019-1-1 “Classification of
environmental conditions; Storage,” Class 1.2
♦ETSI EN 300 019-1-2 “Classification of
environmental conditions, Transportation,” Class
2.3
♦ETSI EN 300 019-1-3 “Classification of
environmental conditions, Stationary use at
weather-protected locations,” Class 3.3
The equipment is designed to function without degra-
dation during exposure to all test severities per Class
3.3.