Advantech UNO-1110 User manual

User Manual
UNO-1110
TI Cortex AM3505 DIN-rail PC
with 2 x LAN, 5 x COM, 4 x USB

UNO-1110 User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2013
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable. How-
ever, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringe-
ments of the rights of third parties, which may result from its use.
Acknowledgements
Intel and Pentium are trademarks of Intel Corporation.
Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for two years from the date of pur-
chase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Advantech, or which have been
subject to misuse, abuse, accident or improper installation. Advantech assumes no
liability under the terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is defec-
tive, it will be repaired or replaced at no charge during the warranty period. For out-
of-warranty repairs, you will be billed according to the cost of replacement materials,
service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandize
authorization) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt)
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid
to your dealer.
Part No. 2003111000 Edition 1
Printed in Taiwan November 2013

iii UNO-1110 User Manual
Declaration of Conformity
CE
This product has passed the CE test for environmental specifications when shielded
cables are used for external wiring. We recommend the use of shielded cables. This
kind of cable is available from Advantech. Please contact your local supplier for
ordering information.
FCC Class A
Note: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Opera-
tion of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
Technical Support and Assistance
1. Visit the Advantech web site at http://support.advantech.com where you can
find the latest information about the product.
2. Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before you call:
–Product name and serial number
–Description of your peripheral attachments
–Description of your software (operating system, version, application software,
etc.)
–A complete description of the problem
–The exact wording of any error messages

UNO-1110 User Manual iv
Safety Instructions
1. Read these safety instructions carefully.
2. Keep this User Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the equip-
ment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting
it fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment
from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source
to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
14. If one of the following situations arises, get the equipment checked by service
personnel:
15. The power cord or plug is damaged.
16. Liquid has penetrated into the equipment.
17. The equipment has been exposed to moisture.
18. The equipment does not work well, or you cannot get it to work according to the
user's manual.
19. The equipment has been dropped and damaged.
20. The equipment has obvious signs of breakage.
21. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE
STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE 60° C
(140° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT
SHOULD BE IN A CONTROLLED ENVIRONMENT.
22. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY
REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE
RECOMMENDED BY THE MANUFACTURER, DISCARD USED BATTERIES
ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.
23. The sound pressure level at the operator's position according to IEC 704-1:1982
is no more than 70 dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech
disclaims all responsibility for the accuracy of any statements contained herein.

v UNO-1110 User Manual
Safety Precaution - Static Electricity
Follow these simple precautions to protect yourself from harm and the products from
damage.
To avoid electrical shock, always disconnect the power from your PC chassis
before you work on it. Don't touch any components on the CPU card or other
cards while the PC is on.
Disconnect power before making any configuration changes. The sudden rush
of power as you connect a jumper or install a card may damage sensitive elec-
tronic components.

UNO-1110 User Manual vi

vii UNO-1110 User Manual
Chapter 1 Overview...............................................1
1.1 Introduction ............................................................................................... 2
1.2 Features ................................................................................................... 2
1.3 Hardware Specifications .......................................................................... 2
1.4 Chassis Dimensions................................................................................. 4
Figure 1.1 UNO-1110 Top View Dimensions............................... 4
Figure 1.2 UNO-1110 Side View Dimensions.............................. 4
Chapter 2 Installation............................................5
2.1 Overview ................................................................................................... 6
Figure 2.1 UNO-1110 I/O Overview............................................. 6
Table 2.1: UNO-1110 I/O Overview............................................. 7
2.2 LED Indicators........................................................................................... 7
Table 2.2: UNO-1110 LED Indicator Definitions.......................... 7
2.3 Network Connections ................................................................................ 8
Table 2.3: Ethernet RJ-45 Connector Pin Assigns ...................... 8
2.4 Serial Connections .................................................................................... 9
2.4.1 Serial Mode and Terminator Resistor Selection ........................... 9
Table 2.4: COM1 - COM4 Serial Port Setting.............................. 9
Table 2.5: COM1 - COM4 Pin Assignments.............................. 10
Figure 2.2 COM5 RS-485 Pin Assignments .............................. 10
2.5 Power Connections ................................................................................. 10
Figure 2.3 Power Pin Assignments ........................10
Table 2.6: Power Pin Assignments............................................ 10
2.6 Digital Input/Output ................................................................................. 11
Figure 2.4 Digital I/O Pin Assignments ...................................... 11
Figure 2.5 Digital Input Connection (Dry Contact) ..................... 11
Figure 2.6 Digital Output Connections....................................... 11
2.7 Simulation DI........................................................................................... 12
Table 2.7: Simulation DI Setting ................................................ 12
2.8 USB Connector ....................................................................................... 12
Table 2.8: USB Connector Pin Assignments............................. 12
2.9 VGA......................................................................................................... 12
Table 2.9: VGA Adaptor Cable Pin Assignments ...................... 12
2.10 Reset Button ........................................................................................... 13
2.11 SD Slots .................................................................................................. 13
2.12 Debug Port .............................................................................................. 13
Table 2.10: Debug Port Pin Assignments.................................... 13
2.13 Mounting ................................................................................................. 14
2.13.1 Wall Mounting ............................................................................. 14
Figure 2.7 Wallmount Kit Hole Dimensions ............................... 14
2.13.2 DIN-rail Mounting ........................................................................ 14
Figure 2.8 Combine the DIN-rail Mounting Kit ........................... 14
Chapter 3 Advanced Applications.....................15
3.1 Networking ............................................................................................. 16
Figure 3.1 Network and Dial-up Connections ............................ 16
Figure 3.2 Selected Connection ................................................ 16
Figure 3.3 Setting IP Address.................................................... 16
3.2 ActiveSync Connection ........................................................................... 17
Figure 3.4 Network and Dial-up Connections ............................ 17
Figure 3.5 Selected Connection ................................................ 17
Figure 3.6 Select a device ......................................................... 18
Figure 3.7 Device properties...................................................... 18
Figure 3.8 Icon of ActiveSync / Mobile Device Center.............. 18

UNO-1110 User Manual viii
Figure 3.9 Selected Connection Settings ................................. 19
Figure 3.10 Allow connections to COM ...................................... 20
Figure 3.11Connect ActiveSync ................................................. 21
Figure 3.12ActiveSync Status .................................................... 21
Figure 3.13Set up a Partnership................................................. 22
Figure 3.14Connected Dialog..................................................... 23
Figure 3.15 Content of UNO-1110.............................................. 24
3.3 Remote Access Server Configuration..................................................... 25
Figure 3.16Network and Dial-up Connections............................ 25
Figure 3.17Selected Make New Connection .............................. 25
Figure 3.18Make New Connection ............................................. 25
Figure 3.19Selected a Modem ................................................... 26
Figure 3.20Enter the Telephone Number ................................... 26
Figure 3.21Dial-up Connection................................................... 27
Figure 3.22Dialing Properties ..................................................... 27
Figure 3.23Dialing Patterns ........................................................ 28
Figure 3.24Status of My Connection .......................................... 28
Figure 3.25Selected Control Panel............................................. 29
Figure 3.26Selected RAS Server ............................................... 29
Figure 3.27 Advantech RAS Server Configuration (General)..... 29
Figure 3.28Advantech RAS Devices .......................................... 30
Figure 3.29Advantech RAS Server Configuration (Logon Security)
30
Figure 3.30Advantech RAS Server Configuration (Users) ......... 31
Figure 3.31Save Registry Setting............................................... 31
3.4 Auto-run Configuration............................................................................ 32
Figure 3.32Selected Configuration Utility ................................... 32
Figure 3.33 Advantech Configurator (Misc)................................ 32
Figure 3.34Select the Program................................................... 33
Figure 3.35Add Program Success.............................................. 33
3.5 Application Development Procedure....................................................... 34
3.5.1 Application Development Procedure .......................................... 34
Figure 3.36New Project of Visual Studio .................................... 34
Figure 3.37Selected SDK of UNO-1110..................................... 35
Figure 3.38Select Build Solution ................................................ 35
3.5.2 Watchdog Timer ......................................................................... 36
3.5.3 Simulation DI, DIO and User Programmable LED...................... 41
3.6 Saving Your Settings .............................................................................. 48
Figure 3.39 Select Registry Saver.............................................. 48
Figure 3.40Registry is saved successfully.................................. 48
3.7 Create SD Card for booting .................................................................... 49
3.8 Updating Image & Bootloader................................................................. 52
Figure 3.41Update MLO/ EBOOTSD.nb0 .................................. 52
Figure 3.42Update NK.nbl .......................................................... 52
Figure 3.43My Device in UNO-1110........................................... 53
Figure 3.44Delete Documents and Settings in HardDisk ........... 54
3.9 UNO-1110 Network Administration User Guide...................................... 55
3.9.1 Network Administration............................................................... 55
Figure 3.45 Windows CE Remote Management Tool ................ 55
Figure 3.46Password Properties in Windows CE....................... 56
Figure 3.47 Getway Resetting .................................................... 56
3.9.2 Network Setting .......................................................................... 57
Figure 3.48Remote Admin.......................................................... 57
Figure 3.49System Properties in Windows CE........................... 57
Figure 3.50Windows CE Remote Management ......................... 58
3.9.3 Add/Del Network Adapter ........................................................... 58
Figure 3.51 The Add/Del Network Adapter................................. 58
3.9.4 SMB Server Statistics ................................................................. 58
Figure 3.52The SMB Server Statistics ....................................... 58
3.9.5 Configure FTP Server................................................................. 59

ix UNO-1110 User Manual
Figure 3.53The FTP Server ........................................................ 59
Figure 3.54 The FTP Server Virtual Roots ................................. 60
Figure 3.55FTP Users ................................................................ 60
3.9.6 Telnet Server .............................................................................. 61
Figure 3.56Telnet Server ............................................................ 61
3.9.7 Security ....................................................................................... 62
Figure 3.57Add/Modify Users ..................................................... 62
Figure 3.58Add/Modify Shares ................................................... 62
3.9.8 Printer ......................................................................................... 62
Figure 3.59 Add/Modify Printer ................................................... 62

UNO-1110 User Manual x

Chapter 1
1Overview
This chapter gives background
information on the UNO-1110. It
shows you the UNO-1110 over-
view and specifications.
Sections include:
Introduction
Features
Hardware Specifications
Safety Precautions
Chassis Dimensions

UNO-1110 User Manual 2
1.1 Introduction
Advantech’s UNO-1110 is a RISC-grade embedded platform that offers 2 LANs, 5
serial ports and 4 Digital Inputs and 2 Digital Outputs to fulfill user’s I/O device expan-
sion. For data storage, UNO-1110 also provides a two SDs for OS and data storage.
The UNO-1110 series supports Windows CE and Embedded Linux operating sys-
tems, the customer could choose required OS version and SD storage device
according to application requirements.
The UNO-1110 could operate well under -10 ~ 70°C, its small size and light weight
could fit in industrial robust environment.
With these advantage, the UNO-1110 is suitable for communication gateway for con-
verting communication protocol, and micro controller.
The UNO-1110 is a perfect embedded ready platform that can shorten your develop-
ment time and offer a rich networking interface to fulfill your diverse requirements.
1.2 Features
TI Cortex A8 AM3505 600 MHz Processor
256 MB DDR2 on board
1 RS-485, 4 RS-232/422/485 serial ports
Dual 10/100 Mbps Ethernet
2 SD slots for OS and data storage
4 channel digital inputs and 2 channel digital outputs
Four simulation DI dip switch
4 channel user-defined programmable LEDs
Ready platform for WinCE.NET and Embedded Linux
Built-in Advantech DigAnywhere agent for remote management and diagnosis.
(Windows CE OS only)
Fanless design for reliable system
10 ~ 30 VDC Wide Dual Power Inputs with Reserve Power Polarity Protection
Compact size and light weight
-10 ~ 70°C operating temperature range
DIN-rail and wall mounting
1.3 Hardware Specifications
General
Certifications: CE, FCC Class A, CCC, UL
Dimensions (W*H*D): 50 x 154 x 127 mm
Enclosure: Aluminium with solid mounting hardware
Power Input Range: Dual 10 ~ 30 VDC inputs with reserve power polarity
Mounting: DIN35 rail, wall
Power Consumption: 6 W (Typical)
Power Requirement: 10 ~ 30 VDC (e.g. + 24 VDC @ 1 A) (Min. 24 W), AT
Weight: 450g

3 UNO-1110 User Manual
Chapter 1 Overview
System Hardware
CPU: TI Cortex A8 AM3505 600 MHz
Memory: 256 MB DDR2
VGA: THS8136 controller, DB-15 VGA Connector
Indicators: Power, Serial (Tx, Rx), SD, 4 x DI, 2 x DO, 4 Programmable LEDs
Storage: 2 SD slots
Others: : Real Time Clock, Watch Dog Timer
System Software
OS: WinCE .NET 6.0 / Embedded Linux
Remote Display: DiagAnywhere Utility (Windows CE only)
Communication
Serial Ports:
–1 x RS-485, 4 x RS-232/422/485 (COM1 ~ COM5)
–Automatic RS-485 data flow control
Serial Port Speed:
–RS-232: 300 ~ 115.2 kbps
–RS-422/485: 300 ~ 115.2 kbps
LAN: 2 x 10/100 Base-T RJ-45 ports
Digital I/O (UNO-1110 only)
Digital In:
–4 Digital Input
–Dry Contact:
Logic level 0: Open
Logic level 1: Close
Digital Out:
–2 Digital Output
–Open Collect to 30V
–200mA max Load
–Power Dissipation 450mW
Environment
Operating Temperature: -10 ~ 70°C (14° ~ 158°F)
Safety Cert. Temperature: 60°C
Storage Temperature: -20° ~ 80°C (-4° ~ 176°F)
Operating Humidity: 20 ~ 95% (non-condensing)
Storage Humidity: 0 ~ 95% (non-condensing)

UNO-1110 User Manual 4
1.4 Chassis Dimensions
Figure 1.1 UNO-1110 Top View Dimensions
Figure 1.2 UNO-1110 Side View Dimensions

Chapter 2
2Installation
In this chapter, you will be given
an overview of the UNO-1110
hardware installation procedures.
Sections include:
Overview
LED
Network Connections
Serial Connections
Power Connections
Digital Input/Output
CompactFlash
Mounting

UNO-1110 User Manual 6
2.1 Overview
Figure 2.1 UNO-1110 I/O Overview

7 UNO-1110 User Manual
Chapter 2 Installation
2.2 LED Indicators
LEDs to display the power, SD, Ethernet, Serial, Programmable LED and Digital I/O
status are located on the front panel of UNO-1110, and each of them has its own spe-
cific meaning, as shown in the table below.
Table 2.1: UNO-1110 I/O Overview
Item Description
1 LED Indicators
2VGA
3 Ethernet Ports
4 Serial Ports
5USBPorts
6 Reset Button
7 Simulation DI
8 Power Inputs
9 Chassis Grounding
10 Digital I/O
11 RS-485
12 SD Slots
13 COM Port Setting DIP Switch
14 Debug Port
Table 2.2: UNO-1110 LED Indicator Definitions
LED Color Status Description
PWR Red On System power is on
Off System power is off
SD Green Flash Data is transmitting/receiving
Tx1 ~ Tx4 Yellow Flash Serial port COM1 - COM4 is transmitting data
Rx1 ~ Rx4 Green Flash Serial port COM1 - COM4 is receiving data
PL1 ~ PL4 Green On User Programmable LED on
Off User Programmable LED off
DI0 ~ DI3 Green/
Yellow
On Input High
Off Input Low
DO0 ~ DO1 Green/
Yellow
On Set False
Off Set True
LAN Link Green
On Connected to network
Off Not connected to network
Flash Data is transmitting / receiving
LAN Speed Yellow On Link to 100 Mbps network
Off Link to 10 Mbps network

UNO-1110 User Manual 8
2.3 Network Connections
The UNO-1110 is equipped with a SMSC LAN8720AI (LAN1) & a DAVICOM
DM9000BI (LAN2) Ethernet LAN controller that provide standard RJ-45 jack with 10/
100 Mbps.
LED indicators on the front side to show its Link (Green LED) and Active (Yellow
LED) status.
Table 2.3: Ethernet RJ-45 Connector Pin Assigns
Pin 10/100Base-T Signal Name
1XMT+
2XMT-
3RCV+
4NC
5NC
6RCV-
7NC
8NC

9 UNO-1110 User Manual
Chapter 2 Installation
2.4 Serial Connections
2.4.1 Serial Mode and Terminator Resistor Selection
UNO-1110 provides 5 serial Com ports, COM1 - COM4 provide RS-232/422/485, and
COM5 provides RS-485. The default settings of COM1 - COM4 are RS-232. Users
could change COM1 - COM4 Port serial types to RS-422 or RS-485 by SW3/SW4
DIP switch selection located on rear side of the UNO-1110 system.
You can enable RS-422/485 terminator resistors if necessary to match impedance.
Especially in fields with electric noise, enabling terminal resistors is helpful to stabi-
lize communications. Make sure that both sides of the RS-422 or RS-485 communi-
cation ports are installed on BUS.
Users could change COM1 - COM4 serial port type and RS-422/485 terminator resis-
tor settings by SW3/Serial Port Setting DIP switch located on rear side of the UNO-
1110 system according to the table below.
Table 2.4: COM1 - COM4 Serial Port Setting
COM1/COM3
DIP Switch
COM2/COM4
DIP Switch Serial Mode Receiver Termination Mode
RS-232 Standard Mode N/A
RS-485 Auto Flow Mode 120 Ohms Terminator Resistor
RS-485 Auto Flow Mode No Termination
RS-422 Master 120 Ohms Terminator Resistor
RS-422 Master No Termination

UNO-1110 User Manual 10
Refer to the figure and table below for COM1 - COM4 pin assignment.
Refer to figure below for COM5.
Figure 2.2 COM5 RS-485 Pin Assignments
2.5 Power Connections
UNO-1110 supports +10 ~ 30 VDC power inputs. A detailed power pin description is
shown below.
Figure 2.3 Power Pin Assignments
Table 2.5: COM1 - COM4 Pin Assignments
Pin RS-232 RS-422 RS-485
1 DCD TxD- Data-
2 RxD TxD+ Data+
3 TxD RxD+ -
4 DTR RxD- -
5 GND GND GND
6DSR - -
7RTS - -
8CTS - -
9RI - -
Table 2.6: Power Pin Assignments
Pin Description
V1+ + VDC 1
V2+ + VDC 2
V- PGND
Chassis Grounding