Advantech UNO-1150 User manual

UNO-1150/UNO-1150E
GX2 400MHz Fanless, DIN-rail
Mounted Embedded Automation
Computer with 2 x LAN, 2 x USB,
3 x COM, and Audio and PCI-104
User Manual

UNO-1150 User Manual ii
Copyright Notice
The documentation and the software included with this product are copy-
righted 2009 by Advantech Co., Ltd. All rights are reserved. Advantech
Co., Ltd. reserves the right to make improvements in the products
described in this manual at any time without notice. No part of this man-
ual may be reproduced, copied, translated or transmitted in any form or
by any means without the prior written permission of Advantech Co., Ltd.
Information provided in this manual is intended to be accurate and reli-
able. However, Advantech Co., Ltd. assumes no responsibility for its use,
nor for any infringements of the rights of third parties, which may result
from its use.
Acknowledgements
IBM, PC/AT, PS/2 and VGA are trademarks of International Business
Machines Corporation.
Intel® and Pentium® are trademarks of Intel Corporation.
Microsoft Windows and MS-DOS are registered trademarks of
Microsoft Corp.
C&T is a trademark of Chips and Technologies, Inc.
All other product names or trademarks are properties of their respective
owners.
Part No. 2003115060 1st Edition
Printed in Taiwan February 2009

iii
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its prod-
ucts will be free from defects in materials and workmanship for two years
from the date of purchase.
This warranty does not apply to any products which have been repaired or
altered by persons other than repair personnel authorized by Advantech,
or which have been subject to misuse, abuse, accident or improper instal-
lation. Advantech assumes no liability under the terms of this warranty as
a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous test-
ing, most of our customers never need to use our repair service. If an
Advantech product is defective, it will be repaired or replaced at no
charge during the warranty period. For out-of-warranty repairs, you will
be billed according to the cost of replacement materials, service time and
freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For
example, CPU speed, Advantech products used, other hardware
and software used, etc.) Note anything abnormal and list any
onscreen messages you get when the problem occurs.
2. Call your dealer and describe the problem. Please have your man-
ual, product, and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return
merchandize authorization) number from your dealer. This allows
us to process your return more quickly.
4. Carefully pack the defective product, a fully-completed Repair and
Replacement Order Card and a photocopy proof of purchase date
(such as your sales receipt) in a shippable container. A product
returned without proof of the purchase date is not eligible for war-
ranty service.
5. Write the RMA number visibly on the outside of the package and
ship it prepaid to your dealer.

UNO-1150 User Manual iv
CE
This product has passed the CE test for environmental specifications
when shielded cables are used for external wiring.
FCC Class A
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interfer-
ence when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Technical Support and Assistance
Step 1. Visit the Advantech web site at www.advantech.com/support
where you can find the latest information about the product.
Step 2. Contact your distributor or Advantech's customer service center
if you need additional assistance. Have the following info ready:
- Product name and serial number
- Description of your software (OS, version, software, etc.)
- A complete description of the problem
- The exact wording of any error messages
Packing List
Before setting up the system, check that the items listed below are
included. If any item is not, please contact your dealer immediately.
The UNO-1150 comes with the following items:
• Software CD-ROM
• 6P-6P-6P 20cm PS/2 Mouse/Keyboard Y cable (P/N: 1700060202)
• Phoenix power connector (P/N: 1652003206)
• DIN-rail & Wallmounting accessory
• SATA cable (UNO-1150E only)
• SATA power cable (UNO-1150E only)
• Spacer for PCI-104 expansion (UNO-1150E only)

v
Safety Instructions
1. Read these safety instructions carefully.
2. Keep this User's Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning.
Use a damp cloth. Do not use liquid or spray detergents for clean-
ing.
4. For plug-in equipment, the power outlet socket must be located
near the equipment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Drop-
ping it or letting it fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the
equipment from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before con-
necting the equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not
place anything over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the
power source to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or elec-
trical shock.
13. Never open the equipment. For safety reasons, the equipment
should be opened only by qualified service personnel.
14. If one of the following situations arises, get the equipment checked
by service personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to work
according to the user's manual.
e. The equipment has been dropped and damaged.
f. The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT
WHERE THE STORAGE TEMPERATURE MAY GO BELOW

UNO-1150 User Manual vi
-10° C (14° F) OR ABOVE 60° C (140° F). THIS COULD DAM-
AGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A
CONTROLLED ENVIRONMENT.
16. CAUTION: DANGER OF EXPLOSION IF BATTERY IS
INCORRECTLY REPLACED. REPLACE ONLY WITH THE
SAME OR EQUIVALENT TYPE RECOMMENDED BY THE
MANUFACTURER, DISCARD USED BATTERIES ACCORD-
ING TO THE MANUFACTURER'S INSTRUCTIONS.
The sound pressure level at the operator's position according to IEC 704-
1:1982 is no more than 70 dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1.
Advantech disclaims all responsibility for the accuracy of any statements
contained herein.
Safety Precaution - Static Electricity
Follow these simple precautions to protect yourself from harm and the
products from damage.
1. To avoid electrical shock, always disconnect the power from your
PC chassis before you work on it. Don't touch any components on
the CPU card or other cards while the PC is on.
2. Disconnect power before making any configuration changes. The
sudden rush of power as you connect a jumper or install a card may
damage sensitive electronic components.

vii Table of Contents
Contents
Chapter 1 UNO-1150 Overview ....................................... 2
1.1 Introduction ....................................................................... 2
1.2 Hardware Specifications ................................................... 2
1.3 Safety Precautions ............................................................. 4
1.4 UNO-1150 Series .............................................................. 4
1.5 Chassis Dimensions........................................................... 5
Chapter 2 Hardware Functionality ................................. 8
2.1 UNO-1150 Peripherals...................................................... 8
2.2 COM1: RS-232 Interfaces............................................... 10
2.3 COM2~COM3: RS-232/422/485 Interfaces ................... 10
2.3.1 16C954 UARTs with 128-byte standard ..................... 10
2.3.2 Jumpless for RS-422/485 ............................................. 10
2.3.3 Automatic Data Flow Control Function for RS-485 ... 10
2.3.4 RS-232/422/485 Selection ........................................... 11
2.3.5 Terminal Resistor Setup for RS-422/485 ..................... 12
2.4 LAN: Ethernet Connector ............................................... 14
2.5 Power Connector ............................................................. 14
2.6 LED Indicators ................................................................ 14
2.7 PS/2 Keyboard and Mouse Connector ............................ 14
2.8 Universal Serial Bus Connectors..................................... 15
2.9 VGA: VGA Display Connector ...................................... 15
2.10 RESET: Reset Button...................................................... 15
2.11 Audio............................................................................... 15
2.12 PCI-104 Connectors (UNO-1150E) ................................ 16
Chapter 3 Initial Setup.................................................... 18
3.1 CompactFlash Card Installation ...................................... 18
3.2 PCI-104 Card Installation (Only for UNO-1150E)......... 20
3.3 Hard Drive installation (Only for UNO-1150E) ............. 23
3.4 Chassis Grounding .......................................................... 25
3.5 Power Connection ........................................................... 25
3.6 BIOS Setup and System Assignments ............................ 25
3.7 DIN-rail Mounting Setup ................................................ 26
3.8 Wallmounting Setup........................................................ 27
Appendix A Pin Assignments ............................................ 30
A.1 Board Connectors and Jumpers....................................... 30
A.2 RS-232 Serial Port (COM1)............................................ 33
A.3 RS-232/422/485 Serial Port (COM2~COM3) ................ 34
A.4 Ethernet RJ-45 Connector (LAN1~LAN2)..................... 34
A.5 Power Screw Terminal (CN8)......................................... 35
A.6 PS/2 Keyboard and Mouse Connector (CN10) ............... 35
A.7 USB Connector (CN13) .................................................. 36
A.8 VGA Display Connector (CN15).................................... 36
A.9 CompactFlash Master/Slave & Hard Drive Settings....... 37

UNO-1150 User Manual viii
A.10 RS-422/485 Signal Pull High/Low Settings.................... 38
A.11 Enhanced IDE Connector (CN2) .................................... 39
A.12 SATA Data Connector (CN100) ..................................... 40

1
UNO-1150 Overview
Sections include:
• Introduction
• Hardware Specifications
• Safety Precautions
• UNO-1150 Series
• Chassis Dimensions
CHAPTER

UNO-1150 User Manual 2
Chapter 1 UNO-1150 Overview
1.1 Introduction
UNO-1150 is an DIN-rail mounted Embedded Automation Computer, which
provides several serial communication ports and Ethernet interfaces. UNO-
1150 is designed with a compact size, small footprint, and help to saves space
with its front accessible and DIN-rail design. With rich OS and driver support,
such as Windows XP embedded, WinCE 6.0, and even embedded Linux. You
can integrate your applications easily with an application ready platform that
can provide a versatile function to fulfill diverse requirements.
1.2 Hardware Specifications
• CPU: AMD Geode GX533-400
• Chipset: AMD CS5535
• BIOS: AWARD 4Mbit FLASH BIOS
• RAM: 256MB DDR RAM on board
• VGA: Supports VGA and VESA
- Display memory: 1 ~ 16 MB share memory, set in BIOS
- CRT display: Non-interlaced CRT monitors resolutions up
to 1280 x 1024 @ 256 colors or 1024 x 768 @ 24 bpp
- DB-15 VGA connector
• Audio:
- Line In
- Line Out
• Serial Port: One standard RS-232 ports (COM1),
Two RS-232/422/485 ports (COM2, COM3)
- Data bits: 5, 6, 7, 8
- Stop bits: 1, 1.5, 2
- Parity: none, even, odd
- S p e e d : 5 0 ~ 1 1 5 . 2 k b p s , ( R S - 2 3 2 ) 3 0 0 ~ 9 2 1 . 6 k b p s ( R S - 4 2 2 / 4 8 5 )
- RS-422 data signals: TxD+, TxD-, RxD+, RxD-, GND
- RS-485 Data signal: DATA+, DATA-, GND
- RS-232 Data signal: TxD,RxD,RTS,CTS,DTR,DSR,DCD,RI,GND
- RS-232 Max data distance: 50 feet (15.2 meters)
- RS-422/485 max data distance: 4000 feet (1220 meters)

3
• USB interface: USB OpenHCI, Rev. 1.0 compliant
USB specification version 1.1 compliant
• Ethernet Port: Dual 10/100Base-T Ethernet
- LAN chip: Realtek 8100CL chipset supports
- LED on the front side
• Storage SSD: 1 x internal type I/II CompactFlash slot inside the chassis
HDD: 2.5" SATA HDD bracket (Only for UNO-1150E)
• PC/104: Slot PCI-104 slot, supports 3.3 V & +5 V (Only for UNO-1150E)
• Mini PCI: 1 x MiniPCI (UNO-1150E only)
• LED: 1xPower LED, 1xIDE LED, 3 pairs of serial flow indicators (Tx, Rx )
• Keyboard/Mouse connector: Mini-DIN connector supports PS/2 keyboard
and a PS/2 mouse
• Power Supply Voltage: 10-36 VDC, reversed wiring protection
• Power Consumption: 15W (typical)
• Power Requirement: 24W
• Operating Temperature: -10~60° C (14~140° F)
• Shock Protection: IEC 68 2-27
CompactFlash: 50 G @ wall mount, half sine, 11 ms
HDD: 20 G @ wall mount, half sine, 11 ms (Only for UNO-1150E)
• Vibration Protection: IEC 68 2-64 (Random 1 Oct./min, 1hr/axis.)
CompactFlash: 2 Grms @ 5 ~ 500 Hz,
HDD: 0.5 Grms @ 5 ~ 500 Hz (Only for UNO-1150E)
• Chassis Size (WxLxH): 85 x 155 x 140mm (3.4"x 6.1"x 5.6") (UNO-1150)
110 x 155 x 140mm (4.4"x6.1"x5.6") (UNO-1150E)
• Weight: 1.6 kg (UNO-1150)
1.8kg (UNO-1150E)

UNO-1150 User Manual 4
1.3 Safety Precautions
The following sections tell how to make each connection. In most cases,
you will simply need to connect a standard cable. All of the connector pin
assignments are shown in Appendix A.
Warning!! Always disconnect the power cord from your chassis
when you are working on it. Do not connect while the
power is on. A sudden rush of power can damage sen-
sitive electronic components. Only experienced elec-
tronics personnel should open the chassis.
Caution!! Always ground yourself to remove any static electric
charge before touching UNO-1150. Modern electronic
devices are very sensitive to static electric charges.
Use a grounding wrist strap at all times. Place all elec-
tronic components on a static-dissipative surface or in
a static-shielded bag..
1.4 UNO-1150 Series
There are three products in UNO-1150 series listed as below:
• UNO-1150: UNO-1150 hardware platform
• UNO-1150F: UNO-1150 with one external CompactFlash slot
• UNO-1150E: UNO-1150 with PCI-104 expansion hardware platform

5
1.5 Chassis Dimensions
Figure 1.1: UNO-1150 Chassis Dimensions

UNO-1150 User Manual 6
Figure 1.2: UNO-1150E Chassis Dimensions

2
Hardware
Functionality
Sections include:
•UNO-1150 Peripherals
•COM1: RS-232 Interfaces
•COM2~3: RS-232/422/485 Interfaces
•LAN: Ethernet Connector
•Power Connector
•LED Indicators
•PS/2 Keyboard and Mouse Connector
•Universal Serial Bus Connectors
•VGA: VGA Display Connector
•RESET: Reset Button
•Audio
•PCI-104 Voltage Selection
CHAPTER

UNO-1150 User Manual 8
Chapter 2 Hardware Functionality
2.1 UNO-1150 Peripherals
The following figures show the connectors on UNO-1150 and UNO-
1150E. Information in this chapter is applied to both UNO-1150 and
UNO-1150E. Therefore, in this chapter, we just mention UNO-1150 to
represent the series product.The following sections give you detailed
information about function of each peripheral.
Figure 2.1: UNO-1150 Front View
Figure 2.2: UNO-1150 Top View

9
Figure 2.3: UNO-1150E Front View
Figure 2.4: UNO-1150E Top View

UNO-1150 User Manual 10
2.2 COM1: RS-232 Interfaces
The UNO-1150 offers one standard RS-232 serial communication inter-
face port on COM1. Please refer to A.2 for pin assignments.
2.3 COM2~COM3: RS-232/422/485 Interfaces
The UNO-1150 offers two RS-232/422/485 serial communication inter-
face ports, and they are COM2 and COM3. Both port can be configured
individually to either RS-232, RS422/485 by using on-board jumpers.
Please refer to A.3 for pin assignments and Table 2.1 lists the default set-
ting of each port.
2.3.1 16C954 UARTs with 128-byte standard
Advantech UNO-1150 comes standard with Oxford 16PCI952 UARTs
containing 128 bytes FIFOs. These upgraded FIFOs greatly reduce CPU
overhead and are an ideal choice for heavy multitasking environments.
2.3.2 Jumpless for RS-422/485
In RS-422/485 mode, UNO-1150 automatically sense signals to match
RS-422 or RS-485 network. No need to change jumpers.
2.3.3 Automatic Data Flow Control Function for RS-485
In RS-485 mode, UNO-1150 automatically senses the direction of incom-
ing data and switches its transmission direction accordingly. Therefore no
handshaking signal (e.g. RTS signal) is necessary. This feature lets you
simply and quickly build an RS-485 network with just two wires. More
importantly, application software previously written for half duplex RS-
232 environments can be maintained without need for modification.
Table 2.1: COM2 & COM3 Default Settings
COM Port Default Setting
COM2 RS-422/485
COM3 RS-422/485

11
2.3.4 RS-232/422/485 Selection
COM2 and COM3 support 9-wire RS-232, RS-422 or RS-485 interfaces,
and you can set corresponding jumpers to select serial ports as RS-232 or
RS-422/485 interfaces shown in Table 2.2. Please note to reset the system
to adapt this configuration change
The system detects RS-422 or RS-485 signals automatically in RS-422/
485 mode.
Jumper Setting for RS-422/485 Interface: (Default Setting)
Figure 2.5: RS-422/485 Jumper Settings
Jumper Setting for RS-232 Interfaces:
Figure 2.6: RS-232 Jumper Settings
Table 2.2: Selecting RS-232/422/485 (COM2&3)
Serial Port Corresponding Jumper to Select RS-232/422/485
COM2 CN11
COM3 CN4

UNO-1150 User Manual 12
2.3.5 Terminal Resistor Setup for RS-422/485
The onboard termination resistor (120 Ohm) for COM2/COM3 can be
used for long distance transmission or device matching. (Default Open.)
Each terminal resistor responds to different channels for RS-422/485.
Usually, these resistors are needed for both ends of the communication
wires and the value of the resistors should match the characteristic imped-
ance of the wires used.
Table 2.3: Terminal Resistor Settings
COM port Switch No. Pin Setting Description
COM2 SW4 1 ON 120 Ohm between Data+/
Data- (RS-485)
Or 120 Ohm between Tx+/Tx-
(RS-422)
OFF Open (Default)
2 ON 120 Ohm between Rx+/Rx-
(RS-422)
OFF Open (Default)
COM3 SW1 1 ON 120 Ohm between Data+/
Data- (RS-485)
Or 120 Ohm between Tx+/Tx-
(RS-422)
OFF Open (Default)
2 ON 120 Ohm between Rx+/Rx-
(RS-422)
OFF Open (Default)