Advantech UNO-3200G Series User manual

User Manual
UNO-3200G Series 電腦
Intel® SKYLAKE-H Core®
Processors Embedded
Automation PC, with 2x PCI(e)/
PCI Extension Slots

UNO-3200G Series User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2016
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable. How-
ever, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringe-
ments of the rights of third parties, which may result from its use.
Acknowledgements
Intel® is trademarks of Intel Corporation.
Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.
C&T is a trademark of Chips and Technologies, Inc.
All other product names or trademarks are properties of their respective owners.
Support
For more information on this and other Advantech products, please visit our websites
at: http://www.advantech.com
For technical support and service, please visit our support website at:
http://support.advantech.com/
This manual applies to the below model which is abbreviated as UNO-3283G series
products in this article.
*Model number:
UNO-3283G
*Part number:
UNO-3283G-674AE
UNO3283G6741601E-T
UNO3283G6741602E-T
UNO3283G6741603E-T
UNO3283G6741604E-T
UNO3283G6741605E-T
UNO3283G6741701E-T
UNO3283G6741702E-T
UNO3283G6741703E-T
UNO3283G6741704E-T
UNO3283G6741705E-T
UNO3283G6741706E-T
UNO3283G6741801E-T
UNO3283G6741802E-T
UNO3283G6741803E-T
PN: 2003U32000 Edition 1
Printed in Taiwan September 2016

iii UNO-3200G Series User Manual
UNO3283G6741804E-T
UNO3283G6741805E-T
UNO3283G6741806E-T
UNO3283G6741901E-T
UNO3283G6741902E-T
UNO3283G6741903E-T
UNO3283G6741904E-T
UNO3283G6741905E-T
UNO3283G6741906E-T
UNO3283G6742001E-T
UNO3283G6742002E-T
UNO3283G6742003E-T
UNO3283G6742004E-T
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for two years from the date of pur-
chase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Advantech, or which have been
subject to misuse, abuse, accident or improper installation. Advantech assumes no
liability under the terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is defec-
tive, it will be repaired or replaced at no charge during the warranty period. For out-
of-warranty repairs, you will be billed according to the cost of replacement materials,
service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandize
authorization) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt)
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid
to your dealer.

UNO-3200G Series User Manual iv
Declaration of Conformity
CE
This product has passed the CE test for environmental specifications when shielded
cables are used for external wiring. We recommend the use of shielded cables. This
kind of cable is available from Advantech. Please contact your local supplier for
ordering information.
FCC Class A
Note: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Opera-
tion of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
警告使用者：這是甲類資訊產品，在居住的環境中使用時， 可能會造成射頻干擾，在
這種情況下，使用者會被要求採取某些適當對策。
Technical Support and Assistance
1. Visit the Advantech web site at http://support.advantech.com where you can
find the latest information about the product.
2. Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before you call:
–Product name and serial number
–Description of your peripheral attachments
–Description of your software (operating system, version, application software,
etc.)
–A complete description of the problem
–The exact wording of any error messages
Safety Precaution - Static Electricity
Follow these simple precautions to protect yourself from harm and the products from
damage.
To avoid electrical shock, always disconnect the power from your PC chassis
before you work on it. Don't touch any components on the CPU card or other
cards while the PC is on.
Disconnect power before making any configuration changes. The sudden rush
of power as you connect a jumper or install a card may damage sensitive elec-
tronic components.

v UNO-3200G Series User Manual
Safety Instructions
1. Read these safety instructions carefully.
2. Keep this User Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the equip-
ment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting
it fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment
from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source
to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
14. If one of the following situations arises, get the equipment checked by service
personnel:
The power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment does not work well, or you cannot get it to work according to the
user's manual.
The equipment has been dropped and damaged.
The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE
STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE 60° C
(140° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT
SHOULD BE IN A CONTROLLED ENVIRONMENT.
16. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY
REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE
RECOMMENDED BY THE MANUFACTURER, DISCARD USED BATTERIES
ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.
17. The sound pressure level at the operator's position according to IEC 704-1:1982
is no more than 70 dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech
disclaims all responsibility for the accuracy of any statements contained herein.

UNO-3200G Series User Manual vi
安全指示
1. 請仔細閱讀此安全操作說明。
2. 請妥善保存此用戶手冊供日後參考。
3. 用濕抹布清洗設備前，請確認拔除電源線。請勿使用液體或去污噴霧劑清洗設
備。
4. 對於使用電源線的設備，設備周圍必須有容易接觸到的電源插座。
5. 請勿在潮濕環境中試用設備。
6. 請在安裝前確保設備放置在可靠的平面上，意外摔落可能會導致設備損壞。
7. 設備機殼的開孔適用於空氣對，從而防止設備過熱。請勿覆蓋開孔。
8. 當您連接設備到電源插座前，請確認電源插座的電壓符合要求。
9. 請將電源線佈置在人們不易絆倒的位置，請勿在電源線上覆蓋任何雜物。
10. 請注意設備上所有的警告標示。
11. 如果長時間不使用設備，請拔除與電源插座的連結，避免設備被超標的電壓波動
損壞。
12. 請勿讓任何液體流入通風口，以免引起火灾或短路。
13. 請勿自行打開設備。為了確保您的安全，請透過經認證的工程師來打開設備。
14. 如遇下列情况，請由專業人員維修：
電源線或插頭損壞；
設備內部有液體流入；
設備曾暴露在過度潮濕環境中使用；
設備無法正常工作，或您無法透過用戶手冊來正常工作；
設備摔落或損壞；
設備有明顯外觀損；
15. 請勿將設備放置在超出建議溫度範圍的環境，即不要低於 ‐20 ℃ （‐4 ℉）
或高於 60 ℃ （140 ℉），否則可能會造成設備損壞。
16. 注意：若電池更換不正確，將有爆炸危險。因此，只可以使用製造商推薦的同一
種或者同等型號的電池進行替換。請按照製造商的指示處理舊電池。
17. 本產品於國內裝置使用時，其電源僅限使用機架電源模組所提供直流電源輸入，
不得使用交流電源及附加其他電源轉換裝置提供電源，其電源輸入電壓及電流請
依說明書規定使用。
18. 根據 IEC 704‐1:1982 規定，操作員所在位置音量不可高於 70 分貝。
19. 限制區域：請勿將設備安裝於限制區域使用。
20. 免責聲明：請安全訓示符合 IEC 704‐1 要求。研華公司對其內容之準確性不承
擔任何法律責任。

vii UNO-3200G Series User Manual
RoHS Claim
設備名稱：電腦 型號 （型式）：UNO-3200G Series
Equipment name Type designation (Type)
單元 Unit
限用物質及其化學符號
Restricted substances and its chemical symbols
鉛Lead
(Pb)
汞Mercury
(Hg)
鎘
Cadmium
(Cd)
六價鉻
Hexavalent
chromium
(Cr+6)
多溴聯苯
Polybromina
ted
biphenyls
(PBB)
多溴二苯醚
Polybrominate
d diphenyl
ethers (PBDE)
電路板—○○○○ ○
機殼
( 外殼、支架
…等)
○○○○○ ○
其它固定組件
(螺絲) —○○○○ ○
配件(線材)—○○○○ ○
記憶卡 —○○○○ ○
備考 1.“ 超出 0.1 wt %” 及 “ 超出 0.01 wt %” 係指限用物質之百分比含量超出百分比含
量基準值。
Note 1. “Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage
content of the restricted substance exceeds the reference percentage value of presence
condition.
備考 2.“ ○ ” 係指該項限用物質之百分比含量未超出百分比含量基準值。
Note 2. “ ○”indicates that the percentage content of the restricted substance does not
exceed the percentage of reference value of presence.
備考 3.“ － ” 係指該項限用物質為排除項目。
Note 3?The“?” indicates that the restricted substance corresponds to the exemption.

UNO-3200G Series User Manual viii

ix UNO-3200G Series User Manual
Chapter 1 Overview...............................................1
1.1 Introduction ............................................................................................... 2
1.2 Hardware Specifications ........................................................................... 2
1.2.1 General ......................................................................................... 2
1.3 System Hardware...................................................................................... 3
1.3.1 I/O Interfaces ................................................................................ 3
1.3.2 Environment.................................................................................. 4
1.3.3 Expansion Board (Optional).......................................................... 4
1.4 Safety Precautions .................................................................................... 4
1.5 Chassis Dimensions.................................................................................. 5
Figure 1.1 UNO-3283G Dimensions............................................ 5
1.6 Accessories............................................................................................... 5
Chapter 2 Hardware Functionality.......................7
2.1 Introduction ............................................................................................... 8
Figure 2.1 UNO-3283G Front View ............................................. 8
2.2 Serial Interface (COM1/COM2)................................................................. 8
Figure 2.2 Serial Interface (COM1, COM2) ................................. 9
2.2.1 RS-232/422/485 Interface (COM1 & COM2) ................................ 9
2.2.2 To switch the internal SW1/SW2/SW3 according to the placement
10
Figure 2.3 COM setting.............................................................. 10
Figure 2.4 COM1 RS422 Rx termination (pin1-pin2)................. 10
Figure 2.5 COM2 RS422 Rx termination (pin3-pin4)................. 11
2.3 LAN: Ethernet Connector ........................................................................ 11
2.4 Power Connector .................................................................................... 11
2.5 USB Connector ....................................................................................... 11
2.6 Display Connector................................................................................... 11
2.7 RTC Battery ............................................................................................ 12
2.8 Power Button/Power Management ......................................................... 12
2.8.1 Power mode switch..................................................................... 12
Figure 2.6 AT/ATX Adjustment .................................................. 12
2.9 PCI Express Mini Card Socket................................................................ 13
Figure 2.7 PCIE mini card sockets placement........................... 13
2.9.1 iDoor Expansion Slot .................................................................. 13
2.10 PCIe/PCI Slot .......................................................................................... 13
2.11 SATA HDD Drive..................................................................................... 14
Figure 2.8 SATA Mode Selection .............................................. 14
Figure 2.9 Detecting a RAID configuration ................................ 14
Figure 2.10Creating a RAID Volume .......................................... 15
2.12 Audio Jack............................................................................................... 15
2.13 LED Indicators......................................................................................... 15
Chapter 3 Initial Setup ........................................17
3.1 Connecting Power................................................................................... 18
Figure 3.1 Power Connector...................................................... 18
3.2 Inserting an iDoor Module ....................................................................... 18
3.3 Installing a Hard Disk .............................................................................. 20
3.4 Installing an Interface Card or CFast Card............................................. 21
3.5 Mounting UNO-3283G Series ................................................................. 22
Figure 3.2 Stand Mount ............................................................. 22
Figure 3.3 Enclosure Mount....................................................... 22
Figure 3.4 Wall Mount (01) ........................................................ 23
Figure 3.5 Wall Mount (02) ........................................................ 23

UNO-3200G Series User Manual x
Appendix A System Settings and Pin Assignments
25
A.1 System I/O Address and Interrupt Assignment....................................... 26
Table A.1: Interrupt Assignments .............................................. 26
A.2 Board Connectors and Switches............................................................. 27
Figure A.1 Bottom view of System Board .................................. 27
A.3 Function of connectors & switches ......................................................... 28
Table A.2: Connectors on System board................................... 28
A.4 Audio (Pin header) .................................................................................. 29
Table A.3: CN9 Audio ................................................................ 29
A.5 COM1...................................................................................................... 30
Table A.4: CN3 COM1............................................................... 30
A.6 COM2...................................................................................................... 31
Table A.5: CN4 COM2............................................................... 31
A.7 COM3/COM4 .......................................................................................... 32
Table A.6: CN5 COM3/COM4 ................................................... 32
A.8 Power Connector (PWR) ........................................................................ 33
Table A.7: Power connector pin assignments ........................... 33
A.9 Relay Connector (PWR) ......................................................................... 33
Table A.8: Relay Connector (PWR)........................................... 33
A.10 SW7 Power Switch ................................................................................. 33
Table A.9: SW4 Power Switch................................................... 33
A.11 CN19/CN20 Mini PCIE............................................................................ 34
Table A.10:CN19/CN20 Mini PCIE ............................................. 34
A.12 CN19 mSATA ......................................................................................... 36
Table A.11:CN19 mSATA........................................................... 36
A.13 VO1 reserve for power output, the voltage is same as power input ....... 38
Table A.12:VO1 reserve for power output, the voltage is same as
power input............................................................... 38
A.14 CN1 Internal 12V power for PCI/PCIe .................................................... 39
Table A.13:CN1 Internal 12V power for PCI/PCIe...................... 39

Chapter 1
1Overview
This chapter provides an overview
of UNO-3283G series' specifica-
tions.
Sections include:
Introduction
Hardware specification
Safety precautions
Chassis dimensions
Accessories

UNO-3200G Series User Manual 2
1.1 Introduction
The high performing UNO-3283G models are configured with high-performance Intel
Gen.6 Quad Core i7 processor and QM170 PCH, which offers users the maximum
flexibility, two displays, six USB 3.0 ports, two mPCIe sockets, and up to three expan-
sion slots including one PCIex16 slot, one PCI slot and one iDoor expansion, iDoor
technology supports automation feature extensions such as industry Fieldbus com-
munication, POE, COM & Digital I/O. The UNO-3283G has a variety of convenient
designs, captive thumb screw, dual hot-Swappable HDD/SSD slots, exchangeable
RTC battery can facilitate the maintenance work, and preventing unstable environ-
ment like as power drop via dual power input.
1.2 Hardware Specifications
1.2.1 General
Certification:
–CE, FCC, UL, CCC, BSMI
Dimensions (W×D×H):
–UNO-3283G: 142 x 238 x 177 mm (5.6'' x 9.3'' x 6.9'')
Mounting: Wall mount, Stand mount, enclosure mount
Power Consumption: 30 W (Typical, no card added)
Power Requirements: 10Vdc-36Vdc, support AT/ATX power mode BIOS AT
simulation mode (support system reboot automatically after power recovery)
Weight: UNO-3283G 4.5 kg
OS Support: Windows7/8, WES7, Win10 Enterprise LTSB, AdvLinux
System Design: Fanless

3 UNO-3200G Series User Manual
Chapter 1 Overview
1.3 System Hardware
CPU:
–UNO-3283G-674AE: Intel Core® i7-6822EQ (8M Cache, 2.0GHz)
Memory: 8G DDR4 built-in
Indicators: LEDs for Power, Battery, HDD, COM (Tx/Rx)
Storage: 2 × 2.5" SATA HDD/SSD bays, support 9.5mm height & SATA Gen3.0,
1 x mSATA slot, 1 x CFast slot
Watchdog Timer: 256 levels time interval, programmable from 0 to 255 sec
Expansion Slots:
–UNO-3283G: 2 Full-size mPCIe, 1x PCIex16, 1x PCIx1
PCIE max speed is 5GT/s; PCI max speed is 66MHz; system can provide
typical 10W for each PCI/PCIE slot, Max 20W for single slot condition:
Each PCI/PCIE slot can support below power rail:
1.3.1 I/O Interfaces
Serial Ports: 2 x RS-232/422/485, DB9, auto flow control, 50 ~ 115.2 kbps
LAN Ports: 2 x RJ45, 10/100/1000 Mbps IEEE 802.3u 1000Base-T Fast Ether-
net
USB Ports: 6 x USB 3.0 Ports
Displays: 1 x HDMI, supports 1920 x 1080 @ 24 Hz 24 bpp; 1 x DVI-I, supports
1920 x 1080 @ 60 Hz 24 bpp & 2 independent displays
Power Connector: 1 x 3 pin, terminal block
Condition Slot1 power Slot2 power Total Power limitation
(slot1 + slot2 power)
1typical 10W,
Max 20W NA <20W (Note1)
2NA typical 10W,
Max 20W <20W (Note1)
3typical 10W,
Max 20W
typical 10W,
Max 20W <40W (Note1)
Slot type A: 3.3V B: 5V C: 12V D:-12V Note
PCI slot typical 3.03A
Max 6.06A
typical 2A
Max 4A
typical 0.83A
Max 1.66A Max 0.5A
A+B+C+D,
total
power<20W
PCIE slot typical 3.03A
Max 6.06A
typical 2A
Max 4A
typical 0.83A
Max 1.66A N/A A+B+C, total power<20W
Note! Total power consumption combined on PCI and PCIe slots should be
less than 40 Watt.

UNO-3200G Series User Manual 4
1.3.2 Environment
Relative Humidity: 95% @40°C (Non-condensing)
Operating Temperature: -20 ~ 60°C (-4 ~ 140°F) @ 5 ~ 85% RH with 0.7m/s
airflow (Safety certification: -20 ~ 45°C (-4 ~ 113°F) )
Storage Temperature: - 40 ~ 85°C (-104 ~ 185°F)
Shock Protection:
–IEC 60068-2-27
–50 G, half sine, 11 ms
Vibration Protection:
–IEC 60068-2-64 (Random 1 Oct./min, 1hr/axis.)
–1.5 Grms @ 5 ~ 500 Hz with HDD
–4Grms @ 5 ~ 500 Hz with SSD
1.3.3 Expansion Board (Optional)
Model: UNO-3283G
Optional Expansion Type:
UNO-3283G: 1x PCIex16, 1 x PCI slot; 2x PCIex8 slot; 2x PCI slots;
1.4 Safety Precautions
The following sections tell how to make each connection. In most cases, you will sim-
ply need to connect a standard cable.
Warning! Always disconnect the power cord from your chassis whenever you are
working on it. Do not connect while the power is on. A sudden rush of
power can damage sensitive electronic components. Only experienced
electronics personnel should open the chassis.
Caution! Always ground yourself to remove any static electric charge before
touching UNO-3283G series. Modern electronic devices are very sensi-
tive to static electric charges. Use a grounding wrist strap at all times.
Place all electronic components on a static-dissipative surface or in a
static-shielded bag.

5 UNO-3200G Series User Manual
Chapter 1 Overview
1.5 Chassis Dimensions
Figure 1.1 UNO-3283G Dimensions
1.6 Accessories
Please refer to the below accessories list for UNO-3283G series.
2 × 3-pin plug-in block for power wiring & relay control
1 × Warranty card
1 × UNO series driver &utility DVD-ROM
1 × DVI- VGA connector
142
177
226
95
10
238
95
66
226

UNO-3200G Series User Manual 6

Chapter 2
2Hardware
Functionality
This chapter shows how to setup
UNO-3283G series' hardware
functions, including connecting
peripherals, setting switches and
indicators.
Sections include:
Peripherals
RS-232/422/485 Interface
LAN / Ethernet Connector
Power Connector
Mini PCIe Socket
Audio Connector
USB Connector
DVI-I/HDMI Display Connector

UNO-3200G Series User Manual 8
2.1 Introduction
The following figures show the interfaces of UNO-3283G and the detail information
by each peripheral.
Figure 2.1 UNO-3283G Front View
2.2 Serial Interface (COM1/COM2)
UNO-3283G series offer two standard RS-232/422/485 serial communication inter-
face ports: COM1.
The IRQ and I/O address of serial ports are listed as below.
COM1 (Pin header CN3)
COM2 (Pin header CN4)

9 UNO-3200G Series User Manual
Chapter 2 Hardware Functionality
Figure 2.2 Serial Interface (COM1, COM2)
2.2.1 RS-232/422/485 Interface (COM1 & COM2)
UNO-3200 series offers two serial communication interface port.
SW1 for COM1(RS-232/422/485) switch
SW2 for RS485/422 receiver termination setting
SW3 for COM2(RS-232/422/485) switch
In RS-422/485 mode, the UNO-3200 series automatically detects signals to match
RS-422 or RS-485 networks.
In RS-485 mode, the UNO-3200 series automatically detects the direction of incom-
ing data and switches its transmission direction accordingly. So no handshaking sig-
nal (e.g. RTS signal) is necessary. This lets you conveniently build an RS-485
network with just two wires. More importantly, application software previously written
for half duplex RS-232 environments can be maintained without modification.

UNO-3200G Series User Manual 10
2.2.2 To switch the internal SW1/SW2/SW3 according to the
placement
SW1: COM1 RS232/422/485 mode setting
SW3: COM2 RS232/422/485 mode setting
Figure 2.3 COM setting
SW2: COM1 RS422 Rx termination (pin1-pin2)
Figure 2.4 COM1 RS422 Rx termination (pin1-pin2)