Advantech MIC-3000 Series User manual

Advantech CompactPCI™
Modular Industrial Computer
MIC-3366
6U-size CompactPCI™Low
Power Pentium®III 700MHz
Peripheral Single Board
Computer

MIC-3366 Series User Manual -- Page II
Copyright Notice
This document is copyrighted, 2002. All rights are reserved. Theoriginal
manufacturer reserves the right to make improvements to the products described in
this manual at any time without notice. No part of this manual may be reproduced,
copied, translated or transmitted in any form or by any means without the prior
written permission of the original manufacturer. Information provided in this
manual is intended to be accurate and reliable. However, the original manufacturer
assumes no responsibility for its use, nor for any infringements upon the rights of
third parties which may result from its use.
Acknowledgements
Award is a trademark of Award Software International, Inc.
Fast EtherChannel (FEC) is a trademark of Cisco Systems, Inc.
IBM, PS/2, OS/2, and VGA are trademarks of International Business Machines
Corporation.
Intel®, Pentium®, and PRO/100+ are trademarks of Intel Corporation.
Windows is a registered trademark of Microsoft Corporation.
NetWare is a trademark of Novell, Inc.
Symb ios is a trademark of Symbios Logic Corporation.
PICMG™, CompactPCI™ and the PICMG™, and CompactPCI™ logos are trademarks
of the PCI Industrial Computers Manufacturers Group.
All other product names or trademarks are properties of their respective owners.
CE Notification
The MIC-3366, developed by Advantech CO., LTD., has passed the CE test for
environment specification when shielded cables are used for external wiring. We
recommend the use of shielded cables.
Part No. 2006336600 1st Edition
Printed in Taiwan March 2002

MIC-3366 Series User Manual -- Page III
Product warranty
Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for one year from the date of
purchase. This warranty does not apply to any products which have been repaired or
altered by persons other than repair personnel authorized by Advantech, or which
have been subject to misuse, abuse, accident or improper installation. Advantech
assumes no liability under the terms of this warranty as a consequence of such
events. Because of Advantech’s high quality-control standards and rigorous testing,
most of our customers never need to use our repair service. If an Advantech product
is defective, it will be repaired or replaced at no charge during the warranty period.
For out-of-warranty repairs, you will be billed according to the cost of replacement
materials, service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any on-screen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandize
authorization) number from your dealer. This allows us to process your return more
quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt) in
a shippable container. A product returned without proof of the purchase date is not
eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid to
your dealer.

MIC-3366 Series User Manual -- Page IV
Packing List
Before installing your board, ensure that the following materials have been
received:
• 1 MIC-3366 all-in-one single board computer
• 1 Utility CD-ROM disc
• 1 Heat sink (Assembled)
•1 Thermal pad (Assembled)
• 1 Y-type keyboard/mouse cable
•1 RJ-45 to RS-232 COM port adaptor
•1 Hard drive isolation pad
•1 Solder-side cover (Assembled)
•Several screws
• 1 warranty certificate
• This user's manual
If any of these items are missing or damaged, contact your distributor or sales
representative immediately.
Technical Support and Sales Assistance
If you have any technical questions about the MIC-3366 or any other Advantech
products, please visit our support website at:
• http://support.advantech.com.tw
For more information about Advantech's products and sales information, please
visit:
• http://www.advantech.com.

MIC-3366 Series User Manual -- Page V
Contents
1. Hardware Configuration ............................................................. 1
1.1 Introduction ............................................................................... 2
1.2 Specifications ............................................................................. 3
1.3 Functional Block Diagram ............................................................ 4
1.4 Jumpers .................................................................................... 5
1.4.1 Jumper Locations ........................................................................... 5
1.4.2 Jumper Settings ........................................................................... 6
1.4.3 Clear CMOS (JP2) ......................................................................... 7
1.5 Connectors ............................................................................... 7
1.6 Safety Precautions ..................................................................... 10
1.7 Installing SDRAM (SODIMMs) ...................................................... 10
1.8 Installing CPU and Heat Sink ....................................................... 11
1.9 Software support ....................................................................... 12
2. Connecting Peripherals .............................................................. 13
2.1 IDE Device (CN2) ..................................................................... 14
2.2 VGA Display Connector (Rear I/O) .................................................. 14
2.3 PS/2 Keyboard and Mouse Connector (Through Rear I/O) ................. 14
2.4 Serial Ports (CN7 and through Rear I/O) ......................................... 14
2.5 Ethernet Configuration (CN5) ..................................................... 15
2.6 USB Connector (Through Rear I/O) ................................................ 15
2.7PMC Connector (J11,J12,J14 & J21, J22, J24) ……............................ 15
2.8Card Installation ........................................................................ 15
3. Ethernet Software Configuration ................................................ 17
3.1 Introduction ............................................................................. 18
3.2 Utility and Drivers ...................................................................... 18
3.3 Installation for Windows NT 4.0 ................................................... 19
4. AGP SVGA Setup ...................................................................... 21
4.1 Introduction .............................................................................. 22
4.2 Installation of SVGA Driver .......................................................... 22
4.3Installation for Windows 95/98 ................................................... 22
4.4Installation for Windows NT 4.0 ................................................... 23
4.5Installation for Windows 2000/XP ................................................... 23
4.6Installation for Linux .................................................................... 23
5. AdvanNet Driver Setup ................................................................ 24
5.1 Overview ................................................................................. 25

MIC-3366 Series User Manual -- Page VI
5.2 System Requirements ............................................................. 25
5.3Installation Preparation ............................................................. 25
5.4Installation the Hot Swap Software ................................................ 26
5.5Verifying Installation of the Software .............................................. 27
5.6Installing the AdvanNet Software .................................................. 27
5.7Loading and Running AdvanNet Driver on Linux ................................. 27
6. Award BIOS Setup ................................................................... 30
6.1 AWARD BIOS Setup ................................................................... 31
6.1.1 Entering setup ............................................................................ 31
6.1.2 Standard CMOS setup .................................................................. 31
6.1.3 Advance BIOS features setup ....................................................... 32
6.1.4 Advance Chipset features setup ..................................................... 36
6.1.5 Integrated Peripherals.....................................................................38
6.1.6Power management setup ............................................................. 40
6.1.7PCI configuration setup ................................................................. 42
6.1.8PC Health Status ....................................................................... 43
6.1.9Frequency/Voltage Control ........................................................... 44
6.1.10 Load Fail-safe defaults ................................................................. 45
6.1.11 Load Optimized defaults ............................................................. 45
6.1.12Set Password ....................................................................... 45
6.1.13Save & exit setup ....................................................................... 45
6.1.14Exit without saving ..................................................................... 46
A. Programming the Watchdog Timer .............................................. 47
A.1 Programming the Watchdog Timer ............................................... 48
B. Pin Assignments ....................................................................... 49
B.1 J1 connector ……......................................................................... 50
B.2J2 connector ……........................................................................ 51
B.3 J3 connector ……........................................................................ 52
B.4J5 connector .......................................................................... 53
B.5EIDE connector (CN2)...................................................................54
B.6Ethernet RJ-45 connector (CN5) .................................................... 54
B.7RJ-45-COM1 serial port (CN7) .......................................................55
B.8Fan Power Connector (CN8) ................................................... 55
B.9CompactFlash Socket (CN9) -Optional ........................................... 55
B.10 System I/O Ports ........................................................................ 56
B.11 Interrupt Assignments ................................................................ 57
B.121st MB Memory Map .................................................................. 57

MIC-3366 Series User Manual -- Page VII
Figures
Figure 1-1: MIC-3366 functional block diagram ........................................... 5
Figure 1-2: MIC-3366 jumper and connector locations .................................. 8
Figure 1-3: MIC-3366 front panel connector and indicator locations …………………..9
Figure 1-4: Complete assembly with heat sink and hard disk......................... 11
Figure 2-1: Installing the card into the chassis............................................... 16
Figure 6-1: Setup program initial screen .................................................... 31
Figure 6-2: Standard CMOS setup screen.................................................... 32
Figure 6-3: Advance BIOS features setup screen............................................ 33
Figure 6-4: Advance Chipset features setup screen ........................................ 36
Figure 6-5: Integrated Peripherals setup screen ......................................... 37
Figure 6-6: Power management setup screen ............................................. 40
Figure 6-7: PNP/PCI configuration screen .................................................... 42
Figure 6-8: PC Health setup screen ............................................................ 43
Figure 6-9: Frequency/Voltage Control setup screen...................................... 44

MIC-3366 Series User Manual -- PageVIII
Tables
Table 1-1: MIC-3366 jumper descriptions ................................................... 6
Table 1-2: Clear CMOS............................................................................. 7
Table 1-3 MIC-3366 connector descriptions ............................................... 7
Table 2-1: MIC-3366 serial port default settings ......................................... 15
Table B-1: J1 connector pin assignments ................................................. 50
Table B-2: J2 connector pin assignments ................................................. 51
Table B-3: J3 connector pin assignments ................................................. 52
Table B-4: J5connector pin assignments ................................................ 53
Table B-5:Hard Disk Drive connector ...................................................... 54
Table B-6: MIC-3366 Ethernet RJ-45 connector ............................................ 54
Table B-7: MIC-3366 COM1 serial port ........................................................ 55
Table B-8: Fan Module Connector.............................................................. 55
Table B-9: MIC-3366 CompactFlash socket ................................................ 55
Table B-10: System I/O ports .................................................................... 56
Table B-11: Interrupt assignments ............................................................. 57
Table B-12:1st MB memory map ............................................................... 57

MIC-3366 Series User Manual -- Page 1
1
Hardware
Configuration

MIC-3366 Series User Manual -- Page 2
1.1 Introduction
The MIC-3366 is a 6U-size CompactPCI™all-in-one single board with low power
Pentium®III 700MHz CPU on-board which complies with PICMG 2.0 R2.1
CompactPCI™specifications. Targeting performance-demanding applications like
multi-computing and server blade applications. Based on Intel®’s 440GXchipset,
the MIC-3366 enhances its performance with 100 MHz front side bus.
High Performance Pentium®III Processor
The MIC-3366 integrated an Intel®low power Pentium®III 700MHz processor with
the BGA2package. The low power Pentium®III 700MHz processor has on-chip 256
KB cache providing high performance with low cost. With the support of a 100MHz
CPU bus clock, the MIC-3366 can fulfill custome r’s expectations of
high-performance computing capability.
Compact Mechanical Design
The MIC-3366 has many functions on a single board with only one-slot width.
Advantech provides a CPU heat sink specially designed for the low power Pentium®
III processor, enabling the MIC-3366 to operate without a cooling fan on the heat
sink. It only needs external cooling air from the chassis fans for ventilation. This
enables the MIC-3366 to use a Pentium®III CPU within a mere 1-slot wide space.
Single P2P Bridge
The MIC-3366 with single PCI-to-PCI Bridge (Intel®DEC21555) is purpose as a
slave CPU board that can make it works independently like any peripheral boards,
via AdvanNet driver, it can communicate with system master board by a virtual
Ethernet.
PMC (PCI Mezzanine Card) IEEE1386.1 Compliant
The MIC-3366 supportsup to two PMC sites and compliant with PICMG 2.3 (PCI
Mezzanine Card) specification. These two 32-bit PMC interface provides front access
capability by PMC modules for various function demanding.
Complete I/O Functions
The MIC-3366 offers all the I/O functions of an industrial computer with the rugged
Eurocard form factor. Since two PMC sites knockouts most area of front panel, only
few I/O connectors are available on the front panel including one Ethernet interface,
one serial port, and one PS/2 K/Band mouse. The rest of I/O has fully connected to
the rear I/O module via user-define connector (J3 & J5) on the backplane. These I/O

MIC-3366 Series User Manual -- Page 3
contain two Fast Ethernet interfaces, secondary serial port, one USB port, one VGA
connector, and one PS/2 keyboard/mouse connector. The front panel also has a
reset button and LEDs for power status, HDD operation and Ethernet
communication. The built-in high speed IDE controller provides two separate IDE
channels with Ultra DMA/33 mode. The user-defined J3 connector is designed to
support up to four IDE devices and two floppy drives. These drives can simply be
connected to the backplane or to the rear transition board for easy service and
maintenance.
Meets Industrial and Computer-Telephony Applications Requirements
The MIC-3366 is designed for use in mission critical applications. It accepts a
CompactFlash™memory card (optional) on either the rear transition board or
MIC-3366 itself, thus eliminating the need to use a fragile rotating hard drive. A
watchdog timer can automatically reset the system if the system stops due to a
program bug or EMI. The two-layer front panel design complies with IEEE 1101.10.
Connectors are firmly screwed to the front panel, and the replaceable shielding
gasket is attached to the panel edge. This reduces emissions and gives better
protection against external interference.
1.2 Specifications
Standard SBC Functions
• CPU: BGA2 Low Power Pentium®III Coppermine CPU 700 MHz
• BIOS: Award 2 Mb flash memory
• Chipset: Intel®440GX / 440BX Chipset
• Front Side Bus Clock: 100 MHz for Intel®Pentium®III CPU
• Bus Interface: 32-bit, 33 MHz, PICMG 2.0 compliant
• 2nd level cache: CPU built-in 256 KB (Pentium®III) on die
• RAM: Two 144-pin SO-DIMM sockets. Support PC-100 SDRAMs with memory
capacity up to 1GB (MIC-3366) and 512MB for MIC-3366B. Support ECC.
• Enhanced IDE interface: Two channels handles up to 4 IDE HDDs or other IDE
devices via J3 connector. Supports PIO mode 4 and Ultra DMA/33 mode.
• Floppy disk drive interface: Supports up to two floppy disk drives through the
J3 connector
• Serial ports: Two RS-232 ports with 16C550 compatible UARTs
• USB interface: One USB connector with fuse protection. Complies with USB
specification 1.0
• Keyboard/mouse connectors: One 6-pin mini-DIN connector on the front panel
• Watchdog timer: Can generate a system reset. Software enabled/disabled. Time

MIC-3366 Series User Manual -- Page 4
interval is from 1 to 63 seconds, jumperless with run-time setup.
PCI-to-PCI Bridge
• Controller chip: One (MIC-3366) Intel®DEC 21555 Non-transparent controller
chips.
10/100Base-TX Ethernet Interface
• Controller chips: Two Intel®82559 Fast Ethernet controller chips
• Dual LAN ports (RJ-45)
• 10 Mbps or 100 Mbps auto-switching
AGP VGA Interface
• Controller: Intel®C&T 69030
• AGP 1.0 compliant, 66 MHz
• Display memory: On-chip 4MB SDRAM
• Display ResolutionNumber of Colors:
640 x 480, 800 x 600,
1024 x 768, 1280 x 1024 256 (8 bits)
640 x 480, 800 x 600, 1024 x 768 65, 536 (16 bits)
640 x 480, 800 x 600 16.8 million (24 bits)
Optional Rear I/O Boards
• For MIC-3366: RIO-3306
• For MIC-3366B: RIO-3306
Mechanical and Environmental Specifications
• Operating temperature: 0 ~ 55° C (32 ~ 131° F)
• Storage Temperature: -20 ~ 80° C (-4 ~ 176° F)
• Humidity (operating and storage): 5 ~ 95% (non-condensing)
• Power Consumption: +5 V@ 2.1 A; +3.3 V @ 2.5 A; +12 V @ 640 mA
• Board size: 233.35 x 160 mm (6U size), 1-slot (4 TE) wide
• Weight: 0.8 kg (1.8 lb)
• Shock: 20 G (operating); 50 G (storage/transit)
• Random vibration: 1.5 Grms.
1.3 Functional Block Diagram

MIC-3366 Series User Manual -- Page 5
Figure 1-1: MIC-3366 functional block diagram.
1.4 Jumpers
1.4.1 Jumper Locations
The MIC-3366 provides a jumper (JP2) for configuring your board for specific

MIC-3366 Series User Manual -- Page 6
applications other than the default settings. Table 1-1 lists the jumper function.
Figure 1-2 illustrates the jumper location. Read this section carefully before
changing the jump setting on your MIC-3366 card.
Table 1-1: MIC-3366 jumper descriptions
Number Function
JP1Clear CMOS
JP2 CF Mode (CF Master / Slave)
JP3 Hot-swap connector (For MIC-3366C only)
JP4 System board monitor enable
JP5 External SMBus enable
JP6 Primary PCI VIO
JP7 Secondary PCI VIO
JP8 PMC Module voltage
1.4.2 Jumper Settings
This section tells how to set the jumpers to configure your card. It gives the card
default configuration and your options for each jumper. After you set the jumpers
and install the card, you will also need to run the BIOS Setup program (discussed in
Chapter 6) to configure the serial port addresses, floppy/hard disk drive types and
system operating parameters. Connections, such as hard disk cables, appear in
Chapter 2. For the locations of each jumper, see the board layout diagram depicted
earlier in this chapter.
You configure your card to match the needs of your application by setting jumpers.
A jumper is the simplest kind of electric switch. It consists of two metal pins and a
small metal cap (often protected by a plastic cover) that slides over the pins to
connect them. To "close" a jumper you connect the pins with the cap. To "open" a
jumper you remove the cap. Sometimes a jumper will have three pins, labeled 1, 2
and 3. In this case you connect either pins 1 and 2 or 2 and 3.
The jumper settings are schematically depicted in this manual as follows:
You may find a pair of needle-nose pliers useful for setting the jumpers.

MIC-3366 Series User Manual -- Page 7
If you have any doubts about the best hardware configuration for your application,
contact your local distributor or sales representative before you make any changes.
1.4.3 Clear CMOS (JP1)
This jumper is used to erase CMOS data and reset system BIOS information. Follow
the procedures below to clear the CMOS.
1. Turn off the system.
2. Close jumper JP1(2-3) for about 3 seconds.
3. Close jumper JP1(1-2).
4. Turn on the system. The BIOS is reset to its default setting.
Table 1-2: Clear CMOS
CMOS JP1
Clear
Normal (default)
1.5 Connectors
On-board connectors link to external devices such as hard disk drives, keyboards, or
floppy drives, etc. Table 1-3 lists the function of eachconnector and Figure 1-2 and
Figure 1-3 illustrate each connector location. Chapter 2 gives instructions for
connecting external devices to your card.
Table 1-3 MIC-3366 connector descriptions
Number Function
CN1 Secondary IDE (CompactFlash)–Optional only
CN2 Primary IDE
CN4 SODIMM Socket
CN5 Ethernet RJ-45 Connector
CN7 COM1 RJ-45 Connector
J11/J12/J14 PMC#1 Connector
J21/J22/J24 PMC#2 Connector (Optional)
J1/J2 Primary CompactPCI™bus
J3/J5 Rear I/O transition
LED1 HDD LED and Power LED
SW1 Reset switch
SW2 LAN1 bridging switch to rear I/O (Locate in the solder side)

MIC-3366 Series User Manual -- Page 8
Please refer to Appendix B for pin assignments.
Figure 1-2: MIC-3366 jumper and connector locations.

MIC-3366 Series User Manual -- Page 9
Figure 1-3: MIC-3366 front panel connector and indicator locations

MIC-3366 Series User Manual -- Page 10
1.6 Safety Precautions
Follow these simple precautions to protect yourself from harm and the products
from damage.
1. To avoid electric shock, always disconnect the power from your PC chassis before
you work on it. Don't touch any components on the CPU card or other cards while
the PC is on.
2. Disconnect power before making any configuration changes. The sudden rush of
power as you connect a jumper or install a card may damage sensitive electronic
components.
3. Always ground yourself to remove any static charge before you touch your CPU
card. Be particularly careful not to touch the chip connectors. Modern integrated
electronic devices, especially CPUs and memory chips, are extremely sensitive to
static electric discharges and fields. Keep the card in its antistatic packaging when it
is not installed in the PC, and place it on a static dissipative mat when you are
working with it. Wear a grounding wrist strap for continuous protection.
1.7 Installing SDRAM (SODIMMs)
The MIC-3366 provides two 144-pin SODIMM sockets. Each socket accepts either
16, 32, 64, 128 or 256 MB SDRAM (for MIC-3366B).Also the 512MB SODIMM
support for MIC-3366.The sockets can be filled in any combination with SODIMMs
of any size, giving a total memory capacity between 16 and 512 MB. If only one
SODIMM module is required, it can be installed in either SODIMM socket.
Since the MIC-3366 can operate at 66 or 100 MHz, we recommend using
PC100-compliant SODIMMs. To enable the chipset's Error Checking and Correction
(ECC) function, please use SODIMMs which support the ECC function. The
procedure for installing SODIMMs appears below. Please follow these steps
carefully.
1. Ensure that all power supplies to the system are switched off.
2. Install the SODIMM module. Install the SODIMM so that its gold pins point down
into the SODIMM socket.
3. Slip the SODIMM into the socket at a 45 degree angle and carefully fit the bottom
of the card against the connectors.
4. Gently push the SODIMM into the socket until the clips on the ends of the
SODIMM sockets snap into place.
5. Check to ensure that the SODIMM is correctly seated and all connector contacts
touch. The SODIMM should not move around in its socket.
NOTE: The SODIMM modules can only fit into sockets one way, in accordance with

MIC-3366 Series User Manual -- Page 11
the keyed notches along the bottom edge of the modules. Their gold pins must point
down into the SODIMM socket.
1.8 Installing CPU Heat Sink
The MIC-3366 integrates Intel®Low Power Pentium®III Coppermine CPU. In order
to meet critical environmental conditions and the physical space of the MIC-3366 at
the same time, Advantech designed a heat sink to fulfill its primary needs. Please
refer to Figure 1-4 for an illustration of the heat sink used for the MIC-3366.
The small aluminum plate is default fastened on the CPU in the factory.
When user doing the memory installation, the following steps should be followed:
1. Remove the screws for the solder side cover. At this step, the front panel will be
also loosed. Be careful about any improper disassemble procedure that could
cause any damage of SBC.
2. Remove the rest four screws for heatsink standing, then the heatsink is loose for
memory installation and relavant.
3. Follow the opposed procedure to assembly the heatsink and solder side cover.
Note: The heat pad is sealed between heatsink and CPU is kind of frangible, please
be careful on the disassemble procedure. And be careful with any other damage of
heat pad will cause the thermal issue easily.
Figure 1-4:Complete assembly with heat sink, hard disk and a PMC module

MIC-3366 Series User Manual -- Page 12
1.9 Software support
The MIC-3366 comes with a utility CD-ROM disc, which includes drivers and utility
programs of Ethernet and SVGA interfaces. The 440GX and 440BX chipset may not
be recognized by some old-versioned Windows 95. Please visit Intel®’s website to
download the required files:
http://developer.intel.com/design/chipsets/drivers/inf_update.htm.