Advantech B+B SmartWorx 485OI9TB User manual

1-888-948-2248 | Europe: [phone]
advantech-bb.com
707 Dayton Road | PO Box 1040 | Ottawa, IL 61350
Phone: [phone] | Fax: [phone]
www.advantech-bb.com | E-mail: [e-mail]
Fast and easy on the web: www.advantech-bb.com
QUICK START
GUIDE
D oc um ent Num be r: 710 -11174 - 0 0 _ 48 5O I9T B _ 2117qs g
BAUD TIME-OUT R12 (Ohms) C7 (mfd)
300 33.3 ms 330K 0.1
600 16.6 ms 160K 0.1
1200 8.33 ms 820K 0.01
2400 4.16 ms 430K 0.01
4800 2.08 ms 200K 0.01
6900 1.04 ms 100K 0.01
19.2k 0.520 ms 56K 0.01
38.4k 0.260 ms 27K 0.01
57.6k 0.176 ms 16K 0.01
115.2k 0.0868 ms 8.2K 0.01
Recommended Accessories
12 VDC Power Supply, 6 W,
Stripped/Tinned, Int’l AC Input,
Int’l AC Blades
# SMI6-12-V-ST
Before you begin, be
sure you have the following:
Model 485OI9TB
Optically Isolated RS-232 to
RS-422/485 Converter
+ 485OI9TB Optically Isolated Converter
+ 12 VDC Power Supply (required, sold separately)
+ RS-232 Serial Cable (optional, sold separately)
+ DB9M-DB9M Null Modem (optional, sold separately)
RS-232 Serial Cable,
6 ft. (1.8 m)
# 9PAMF6
DB9 Male to DB9 Male
Null Modem Adapter
# MMNM9
Time-Out Selection
7
The RS-485 driver is enabled by the rst transmission
of the RS-232 side of the transmit data line (Pin 3). Any
transmission on the TD line keeps the RS-485 driver enabled.
The transmitter is disabled approximately 1ms after the last
transmitted character. This 1ms time out should not have to be
changed for data rates of 9600 baud or higher.
If other time-outs are required, R12 and C7 can be replaced
with component values listed in the table below.
Mechanical Diagram
8

RS-232 Side - Powering
4
Product Overview
Getting Started
UL Installation
1
2
The 485OI9TB converts unbalanced, full-duplex RS-232
signals to balanced full-duplex (4-wire) RS-422/485 or half-
duplex (2-wire) RS-485 signals. It provides 1500 Volts RMS
optical isolation of the data lines and ground between the
RS-232 and RS-422/485 signals.
The RS-232 port has a female DB9 connector with Pin 3
(TD), Pin 2 (RD), and Pin 5 (Ground) passed through. The
RS-422/485 port has a 6-position terminal block. The RS-232
side of the converter derives its power from the DTR (Pin 4)
and the RTS (Pin 7) lines. One or the other must be raised to
power the RS-232 side.
The RS-422/485 side is powered by a 12 VDC power supply
(sold separately).
RS-232
DB9 Female Port
(DCE)
485OI9TB SPECIFICATIONS
Power
RS-232
Port-powered from DTR & RTS
handshake lines
Power
RS-422/485
10-14 VDC, 0.9W External power
supply (required, sold separately)
Baud Rate 115.2 kbps
RS-485, 2-Wire Data A(-), Data B(+), GND
RS-422/485,
4-Wire TDA(-), TDB(+), RDA(-), RDB(+), GND
MTBF 272581 hours
Temperature -40 to +85 °C (wide-operating)
• Input Voltage: 10 – 14 VDC.
• Input Power 0.9 Watts.
• Wire Range: 26 – 16 AWG.
• Tightening Torque: 2.0 lb n.
• Temperature rating of eld installed conductors is 105 °C
minimum, sized for 60 °C ampacity.
• Use copper wire only.
• Maximum surrounding ambient air temperature 50 °C.
RS-422/485
6-Position
Terminal Block
1,500 V
Optical Isolation
RS-422/485 Side - Powering
3
RS-422/485 4-Wire
5
RS-422/485 2-Wire
6