Advantech PCIE-1182 Installation and operation manual

PCIE-1182/81 Startup Manual 1
Before you begin installing your card, please make sure that
the following items have been shipped:
1. PCIE-1182/81, Dual/Single port 10 GigE Vision Frame
Grabber
If any of these items are missing or damaged, please con-
tact your distributor or sales representative immediately.
General
• Chipset:
Intel X550-AT10GBASE-T MAC and PHY
Compliant with IEEE 802.3, IEEE 802.3u, IEEE802.3ab,
IEEE802.3x, IEEE802.3af, IEEE802.3at
• Interface:PCIE 3.0 4x
• DataTransferRate:10,000/5,000(Linux only)/1,000
Mbps
• Protection:
ESD: 8KV(Air), 6KV(Contact)
EFT: 2KV
Surge protection: 1KV
Note: For better compatibility, please change the
PCIe settings to Gen 3.0 on device card slot.
MechanicalandEnvironmental
• Dimensions(LxW):167 x 68.9 mm PCIE low prole
• PowerRequirements:
12 VDC direct from PCIe slot, or with optional 12 VDC
AT/ATX power jack input
PoE+ output 60W (2 port) / 30Watt (1 port), protect by
recoverable eFuse
VDC output 12 VDC up to 48Watt (2 port) / 24Watt (1 port),
protect by recoverable eFuse
• NetWeight: 300 g
PCIE-1182/81 2/1 port PCI Express 10 GigE Vision
Frame Grabber
Startup Manual
MainBoardConnectors
Ports Function
RJ Port1 ~ Port 2 10 GigE ports 1~2
Connector1 12V DC output
LEDindicatorsofRJ45(Lan)connector
LEDs Description
Lan LED (In the left of
RJ45 connector) Green: Ethernet connected
Link LED (In the right
of RJ45 connector)
Yellow: 5G/2.5G/1G/100 Mbps
Green: 10G
BracketLEDindicators
LEDs Description
DC 1~2(PCIE-1182)
DC 1 (PCIE-1181) 12V DC output
POE 1~2 (PCIE-1182)
POE 1 (PCIE-1181) Power over Ethernet
Figure 1: Bracket LED Indicators
ConnectorsPackingList
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com
For technical support and service, please visit our
support website at:
http://support.advantech.com.tw/support/default.
aspx
This manual is for the PCIE-1182/81.
Part No. 20411182000
Printed in China
1st Edition
April 2020
Specications

2 PCIE-1182/81 Startup Manual
12VDCOutputConnectorPin-OutAssignment
Port Pin Function
DC1
Pin 1 +12 V
Pin 2 GND
Pin 3 N.C
DC2
Pin 4 N.C
Pin 5 +12V
Pin 6 GND
Figure 2: 12V DC output Connector
AT/ATX12VDCinput4-pinpowerconnector
Pin Function
Pin 1 GND
Pin 2 GND
Pin 3 +12V
Pin 4 +12V
Figure 3: AT/ATX 12V DC input 4-pin Power Connector
12VDCOutputSwitch
Pin Function
1DC power On/O󰀨
2DC power On/o󰀨
Default is power on and API can’t control after power o󰀨.
Figure 4 12V DC Output Switch
BoardIDSwitch
Pin Function
1
Congure di󰀨erent on/o󰀨 position to set-
up the board ID in multi-card scenario
2
3
4
Figure 5 Board ID Switch
Connector(Cont.) Connector(Cont.)

PCIE-1182/81 Startup Manual 3

DeclarationofConformity
FCCClassA
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause interference in which case the user is required to correct
interference at his own expense.
CE
This product has passed the CE test for environmental specications when shielded cables are used for external wiring. We
recommend the use of shielded cables. This kind of cable is available from Advantech. Please contact your local supplier for
ordering information.
Figure 6: Board Layout
BoardLayout