Advantech B+B SmartWorx 485USB9F-2W User manual

Product Overview
Install the Drivers
Loopback Test (4 Wire)
Back to Back Test (2 Wire)
Connect the Converter
1
3
4
2
• The program will install the driver and a
screen will be displayed indicating successful
installation.
• When you connect the converter to your
PC for the rst time, the COM port will be
congured. This could take up to 30 seconds.
Due to the conguration, a loopback test is
not possible with this model. However, two
converters can be used in a back to back
conguration.
Wire the converters as shown below.
Using HyperTerminal or similar program, connect
to the appropriate COM ports. Set the desired
baud rate. Transmit data. If the same string is
returned the test is good.
RS-485
Side
DB9F
USB Side Loopback RDA(-) to TDA(-) and TDB(+) to
RDB(+) as shown in the diagram.
Using Hyper Terminal or similar program,
connect to the appropriate COM port. Set the
desired baud rate. Ensure that Hyper Terminal
local echo is OFF. Transmit data. If the same
character string is returned, the test is good.
Use the included CD to install the converter’s
drivers.
Warning: To prevent installation errors, do
not plug in the hardware until you have al-
ready installed the drivers.
The driver software is contained on the CD
that is packaged with your converter.
• Put the driver CD into the PC. The setup
program should automatically launch.
• Click Next. Accept the license agreement
and click Next again.
PIN 2 Data A (-)
PIN 3 Data B( +)
PIN 4 GND
USB Data A (-)
Data B (+)
GND
To PC
485USB9F-2W RS-485 2-Wire Device
485USB9F-2W Wiring
485USB9F-4W Wiring
USB
To PC
485USB9F-4W
485USB9F-2W
RS-485 4-Wire Device
RS-485 2-Wire Device
Pin 2 RDA(-)
Pin 3 TDB(+)
Pin 7 RDB(+)
Pin 8 TDA(-)
Pin 6 GND
TDA(-)
RDB(+)
TDB(+)
RDA(-)
GND
A detailed description of this test is located in
the technical notes section of our web page,
www.bb-elec.com.

Recommended Accessories
9PAMF6
DB9 Male to
DB9 Female Cable
UH104
4 Port Industrial USB Hub
Locked Serial Numbers
Many B&B Electronics USB to Serial Converters
have a ‘locked serial number” version noted by the
model number sufx “-LS”.
The LS version locks the USB serial number. This
lets multiple devices with the same model number
be used on multiple computers without installing a
driver for each individual product.
For example, in eld service applications tools are
often shared. If the serial number was not locked,
each converter would need to be installed on every
PC in the pool.
Document number – 710-10880-00_485USB9F-xW-xx_4216qsg
1-888-948-2248 | Europe: [phone]
advantech-bb.com
707 Dayton Road | PO Box 1040 | Ottawa, IL 61350
Phone: [phone] | Fax: [phone]
www.advantech-bb.com | E-mail: [e-mail]
Before you begin, be
sure you have the following:
485USB9F-2W, 485USB9F-2W-LS,
485USB9F-4W & 485USB9F-4W-LS
USB to RS-485 Mini Converter
Fast and easy on the web: www.advantech-bb.com
+ USB to RS-485 Mini Converter
+ USB Cable
+ CD ROM with Drivers
QUICK START
GUIDE
Pinouts
5
Troubleshooting
One USB port is required for each installed
device. The USB port can be native to the PC or
it can be a USB port on a USB hub that is
connected to a PC.
To verify the installation you may open the
Windows Device Manager Scroll down to Ports.
Expand the yout window. You should
see the new ports. If there are no exclamation
points or other trouble indicators ports are
installed correctly and ready for use.
Pin RS-485, 4 wire RS-485, 2 wire
1Not Used Not Used
2Receive RDA - Input Data A - Input/Output
3Transmit TDB + Output Data B + Input/Output
4Ground Ground
5Not Used Not Used
6Ground Ground
7Receive RDB + Input Data B + Input/Output
8Transmit TDA - Output Data A - Input/Output