Advantech MIC-3392 User manual

User Manual
MIC-3392
6U CompactPCI Intel Core 2 Duo
Processor Based Board with
Dual PCIe GbE/DDR2/SATA/PMC

MIC-3392 User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2006
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable. How-
ever, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringe-
ments of the rights of third parties, which may result from its use.
Acknowledgements
Intel and Pentium are trademarks of Intel Corporation.
Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for two years from the date of pur-
chase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Advantech, or which have been
subject to misuse, abuse, accident or improper installation. Advantech assumes no
liability under the terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is defec-
tive, it will be repaired or replaced at no charge during the warranty period. For out-
of-warranty repairs, you will be billed according to the cost of replacement materials,
service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandise
authorization) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt)
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid
to your dealer.
Part No. 2002339211 Edition 2
Printed in Taiwan July 2008

iii MIC-3392 User Manual
Declaration of Conformity
CE
This product has passed the CE test for environmental specifications when shielded
cables are used for external wiring. We recommend the use of shielded cables. This
kind of cable is available from Advantech. Please contact your local supplier for
ordering information.
FCC Class A
Note: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Opera-
tion of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
FM
This equipment has passed the FM certification. According to the National Fire Pro-
tection Association, work sites are classified into different classes, divisions and
groups, based on hazard considerations. This equipment is compliant with the speci-
fications of Class I, Division 2, Groups A, B, C and D indoor hazards.
Technical Support and Assistance
1. Visit the Advantech web site at www.advantech.com/support where you can find
the latest information about the product.
2. Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before you call:
–Product name and serial number
–Description of your peripheral attachments
–Description of your software (operating system, version, application software,
etc.)
–A complete description of the problem
–The exact wording of any error messages

MIC-3392 User Manual iv
Warnings, Cautions and Notes
Document Feedback
To assist us in making improvements to this manual, we would welcome comments
and constructive criticism. Please send all such - in writing to: support@advan-
tech.com
Packing List
!MIC-3392 all-in-one single board computer x1
!Utility and user manual (PDF file) CD-ROM disc x1
!CPU Heat sink (Assembled) x1
!Thermal pad for CPU x1
!HDD tray (Assembled) x 1
!North Bridge Heat sink including a thermal PAD for north bridge component
(Assembled) x 1
!Daughter board for SATA HDD (Assembled) x1 (Single PMC version only)
!PMC filler panel(s) (Assembled) x1 (Single PMC version) or x2 (Dual PMC ver-
sion)
!Solder-side cover (Assembled) x1
!RJ45 to DB9 cable x1
!Several screws
!Warranty certificate document x1
!Safety Warnings: CE, FCC class A
If any of these items are missing or damaged, contact your distributor or sales repre-
sentative immediately.
Warning! Warnings indicate conditions, which if not observed, can cause personal
injury!
Caution! Cautions are included to help you avoid damaging hardware or losing
data. e.g.
There is a danger of a new battery exploding if it is incorrectly installed.
Do not attempt to recharge, force open, or heat the battery. Replace the
battery only with the same or equivalent type recommended by the man-
ufacturer. Discard used batteries according to the manufacturer's
instructions.
Note! Notes provide optional additional information.

v MIC-3392 User Manual
Safety Instructions
1. Read these safety instructions carefully.
2. Keep this User Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the equip-
ment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting
it fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment
from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source
to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
14. If one of the following situations arises, get the equipment checked by service
personnel:
15. The power cord or plug is damaged.
16. Liquid has penetrated into the equipment.
17. The equipment has been exposed to moisture.
18. The equipment does not work well, or you cannot get it to work according to the
user's manual.
19. The equipment has been dropped and damaged.
20. The equipment has obvious signs of breakage.
21. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE
STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE 60° C
(140° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT
SHOULD BE IN A CONTROLLED ENVIRONMENT.
22. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY
REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE
RECOMMENDED BY THE MANUFACTURER, DISCARD USED BATTERIES
ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.
23. The sound pressure level at the operator's position according to IEC 704-1:1982
is no more than 70 dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech
disclaims all responsibility for the accuracy of any statements contained herein.

MIC-3392 User Manual vi
Wichtige Sicherheishinweise
1. Bitte lesen sie Sich diese Hinweise sorgfältig durch.
2. Heben Sie diese Anleitung für den späteren Gebrauch auf.
3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie
Keine Flüssig-oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch
zur Reinigung.
4. Die NetzanschluBsteckdose soll nahe dem Gerät angebracht und leicht
zugänglich sein.
5. Das Gerät ist vor Feuchtigkeit zu schützen.
6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen
oder Fallen könnte Verletzungen hervorrufen.
7. Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät vor überhit-
zung schützt. Sorgen Sie dafür, daB diese Öffnungen nicht abgedeckt werden.
8. Beachten Sie beim. AnschluB an das Stromnetz die AnschluBwerte.
9. Verlegen Sie die NetzanschluBleitung so, daB niemand darüber fallen kann. Es
sollte auch nichts auf der Leitung abgestellt werden.
10. Alle Hinweise und Warnungen die sich am Geräten befinden sind zu beachten.
11. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es vom
Stromnetz trennen. Somit wird im Falle einer Überspannung eine Beschädigung
vermieden.
12. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeiten in
das Gerät gelangen. Dies könnte einen Brand bzw. elektrischen Schlag auslö-
sen.
13. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen
Sicherheit nur von authorisiertem Servicepersonal geöffnet werden.
14. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen
und von einer qualifizierten Servicestelle zu überprüfen:
15. Netzkabel oder Netzstecker sind beschädigt.
16. Flüssigkeit ist in das Gerät eingedrungen.
17. Das Gerät war Feuchtigkeit ausgesetzt.
18. Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert oder
Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen.
19. Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.
20. Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.
21. VOSICHT: Explisionsgefahr bei unsachgemaben Austausch der Batterie.Ersatz
nur durch densellben order einem vom Hersteller empfohlene-mahnlichen Typ.
Entsorgung gebrauchter Batterien navh Angaben des Herstellers.
22. ACHTUNG: Es besteht die Explosionsgefahr, falls die Batterie auf nicht fach-
männische Weise gewechselt wird. Verfangen Sie die Batterie nur gleicher oder
entsprechender Type, wie vom Hersteller empfohlen. Entsorgen Sie Batterien
nach Anweisung des Herstellers.
23. Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000 beträgt
70dB(A) oder weiger.
Haftungsausschluss: Die Bedienungsanleitungen wurden entsprechend der IEC-
704-1 erstellt. Advantech lehnt jegliche Verantwortung für die Richtigkeit der in die-
sem Zusammenhang getätigten Aussagen ab.

vii MIC-3392 User Manual
Safety Precaution - Static Electricity
Follow these simple precautions to protect yourself from harm and the products from
damage.
!To avoid electrical shock, always disconnect the power from your PC chassis
before you work on it. Don't touch any components on the CPU card or other
cards while the PC is on.
!Disconnect power before making any configuration changes. The sudden rush
of power as you connect a jumper or install a card may damage sensitive elec-
tronic components.

MIC-3392 User Manual viii

ix MIC-3392 User Manual
Contents
Chapter 1 Hardware Configuration......................1
1.1 Introduction ............................................................................................... 2
Table 1.1: MIC-3392 Variants...................................................... 2
1.2 Specifications ............................................................................................ 2
1.2.1 CompactPCI Bus Interface ........................................................... 2
1.2.2 CPU .............................................................................................. 3
1.2.3 Processor...................................................................................... 3
Table 1.2: Intel Processors.......................................................... 3
1.2.4 BIOS ............................................................................................. 3
1.2.5 Chipset.......................................................................................... 3
1.2.6 Memory......................................................................................... 4
Table 1.3: SODIMM Types (Non-ECC) ....................................... 4
1.2.7 Ethernet ........................................................................................ 5
1.2.8 Storage interface........................................................................... 5
1.2.9 Serial ports.................................................................................... 5
1.2.10 USB port ....................................................................................... 5
1.2.11 LEDs ............................................................................................. 5
1.2.12 Watchdog timer............................................................................. 5
1.2.13 Optional Rear I/O Modules ........................................................... 5
1.2.14 Mechanical and Environmental Specifications.............................. 6
1.2.15 Compact Mechanical Design ........................................................ 6
1.2.16 CompactPCI Bridge ...................................................................... 6
1.2.17 I/O Connectivity............................................................................. 7
1.2.18 PMC (PCI Mezzanine Card) IEEE1386.1 Compliant.................... 7
1.2.19 Hardware Monitor ......................................................................... 7
1.2.20 Super IO........................................................................................ 7
1.2.21 RTC and Battery ........................................................................... 7
1.2.22 IPMI............................................................................................... 7
1.2.23 HPET and IO/APIC ....................................................................... 8
1.3 Functional Block Diagram ......................................................................... 8
Figure 1.1 MIC-3392 functional block diagram ............................ 8
1.4 Jumpers and Switches .............................................................................. 9
Table 1.4: MIC-3392 jumper descriptions.................................... 9
Table 1.5: MIC-3392 switch descriptions..................................... 9
1.4.1 Jumper Settings ............................................................................ 9
Table 1.6: JP2 VGA output settings ............................................ 9
Table 1.7: JP14 PMC2 V(IO) settings ......................................... 9
Table 1.8: JP4 PMC1 PCI bus frequency settings ...................... 9
1.4.2 Clear CMOS (JP1)...................................................................... 10
Table 1.9: JP1 Clear CMOS ...................................................... 10
1.4.3 Switch Settings ........................................................................... 10
Table 1.10:SW5-1 LAN for BMC ................................................ 10
Table 1.11:SW5-2 SATA HDD channel setting (single PMC) .... 10
Table 1.12:SW5-2 SATA HDD channel setting (dual PMC)....... 10
Table 1.13:SW5-3 & SW5-4: COM2 to console or BMC ............ 11
Table 1.14:SW6 IPMI programming setting................................ 11
Table 1.15:SW7 - Master/Drone mode setting ........................... 11
Table 1.16:SW1: BMC Reset Button & Platform Reset Button .. 11
Figure 1.2 MIC-3392 jumper, switch and connector locations... 12
1.5 Connector Definitions.............................................................................. 12
Table 1.17:MIC-3392 connector descriptions............................. 12
1.5.1 VGA Display Connector (VCN1 or rear I/O)................................ 13
1.5.2 Serial Ports (CN9 and Rear I/O) ................................................. 13
1.5.3 USB Connector (CN11/12 and Rear I/O).................................... 13

MIC-3392 User Manual x
1.5.4 CompactFlash Socket (CN10).................................................... 13
1.5.5 SATA daughter board connector (CN4) (Single PMC only)........ 13
1.5.6 Ethernet Configuration (RJ1/RJ2 or Rear I/O RJ1) .................... 14
1.5.7 PMC Connector (J23 for PMC1, Jxx for PMC2) ......................... 14
1.5.8 SW1 (System reset and BMC reset button)................................ 14
1.6 Safety Precautions.................................................................................. 14
1.7 Installing the CPU and Heatsink ............................................................. 15
Figure 1.3 Complete assembly of CPU and heat sink............... 15
1.7.1 CPU & Heatsink Installation Steps ............................................. 16
1.8 Battery Replacement .............................................................................. 17
1.9 Software Support .................................................................................... 17
Chapter 2 AMI BIOS Setup................................. 19
2.1 Introduction ............................................................................................. 20
Figure 2.1 Setup program initial screen..................................... 20
2.2 Entering Setup ........................................................................................ 21
Figure 2.2 Press Del to run Setup ............................................. 21
2.3 Main Setup.............................................................................................. 22
Figure 2.3 Main setup screen.................................................... 22
2.3.1 System time/System date........................................................... 22
2.4 Advanced BIOS Features Setup............................................................. 23
Figure 2.4 Advanced BIOS features setup screen .................... 23
2.4.1 CPU Configuration...................................................................... 24
Figure 2.5 CPU Configuration ................................................... 24
2.4.2 LAN & SMbus Configuration....................................................... 25
Figure 2.6 LAN & SMBus Configuration.................................... 25
Table 2.1: Select SMBus mode................................................. 25
2.4.3 IDE Configuration ....................................................................... 26
Figure 2.7 IDE Configuration..................................................... 26
2.4.4 Floppy Configuration................................................................... 27
Figure 2.8 Floppy Configuration ................................................ 27
2.4.5 Super I/O Configuration.............................................................. 28
Figure 2.9 Super I/O Configuration............................................ 28
2.4.6 ACPI Setting ............................................................................... 29
Figure 2.10ACPI Setting............................................................. 29
2.4.7 Hardware Health Configuration .................................................. 29
Figure 2.11Hardware Health Configuration ................................ 29
2.4.8 Console Redirection Configuration ............................................. 30
Figure 2.12Configure Remote Access types and parameters.... 30
2.5 PCI/PNP Setup ....................................................................................... 31
Figure 2.13PCI/PNP Setup......................................................... 31
2.5.1 Clear NVRAM ............................................................................. 31
2.5.2 Plug and Play O/S ...................................................................... 31
2.5.3 PCI Latency Timer...................................................................... 31
2.6 Boot Setup .............................................................................................. 32
Figure 2.14Boot Setup................................................................ 32
2.6.1 Boot Settings Configuration........................................................ 32
Figure 2.15Boot Settings Configuration...................................... 32
2.7 Security Setup......................................................................................... 33
Figure 2.16Password Configuration ........................................... 33
2.8 Advanced Chipset Settings..................................................................... 34
Figure 2.17Advanced Chipset Setting ........................................ 34
2.8.1 North Bridge Chipset Configuration............................................ 34
Figure 2.18North Bridge Configuration....................................... 34
2.8.2 South Bridge Configuration......................................................... 35
Figure 2.19South Bridge Configuration ...................................... 35
2.9 Exit Option .............................................................................................. 36
Figure 2.20Exit Option................................................................ 36

xi MIC-3392 User Manual
2.9.1 Save Changes and Exit .............................................................. 36
2.9.2 Discard Changes and Exit .......................................................... 36
2.9.3 Load Defaults.............................................................................. 36
Chapter 3 IPMI .....................................................37
3.1 Introduction ............................................................................................. 38
3.2 Definitions ............................................................................................... 38
3.3 IPMI function list...................................................................................... 38
3.3.1 IPMI Device Global Commands.................................................. 39
Table 3.1: Supported IPMI commands ...................................... 39
3.3.2 BMC Device and Messaging Interfaces...................................... 39
Table 3.2: H8S12C bus connection to NIC SMBus ................... 39
Table 3.3: NIC Interrupt ............................................................. 39
Table 3.4: BMC Device and Messaging Commands................. 40
3.3.3 BMC Watchdog Timer Commands ............................................. 40
Table 3.5: BMC Watchdog Timer Commands........................... 40
3.3.4 Chassis Device Commands........................................................ 41
Table 3.6: Chassis Device commands ...................................... 41
3.3.5 Event Commands ....................................................................... 41
Table 3.7: Event commands...................................................... 41
3.3.6 PEF and Alerting Commands ..................................................... 41
Table 3.8: PEF and Alerting commands.................................... 41
3.3.7 SEL Device Commands.............................................................. 42
Table 3.9: SEL Device commands ............................................ 42
3.3.8 SDR Device Commands ............................................................. 42
Table 3.10:SDR Device commands ........................................... 42
3.3.9 FRU data..................................................................................... 42
Table 3.11:FRU Device commands............................................ 42
3.3.10 Sensors and Threshold configuration ......................................... 43
Table 3.12:Sensor List................................................................ 43
Table 3.14:Sensor Device Commands....................................... 44
Table 3.13:Threshold values of sensors..................................... 44
3.3.11 Serial over LAN........................................................................... 44
Table 3.15:LAN Device Commands ........................................... 44
3.3.12 Serial/Modem Device Commands .............................................. 44
Table 3.16:Serial/Modem Device Commands ............................ 44
3.4 BMC Reset.............................................................................................. 45
Appendix A Pin Assignments ...............................47
A.1 J1 Connector........................................................................................... 48
Table A.1: J1 CompactPCI I/O................................................... 48
A.2 J2 Connector........................................................................................... 49
Table A.2: J2 CompactPCI I/O................................................... 49
A.3 J3 Connector........................................................................................... 50
Table A.3: J3 CompactPCI I/O (LPT, FDD, Parallel IDE, 2.16) . 50
A.4 J5 Connector........................................................................................... 51
Table A.4: J5 CompactPCI I/O (VGA, LAN, COM, USB, PS/2) . 51
A.5 Other Connectors.................................................................................... 51
Table A.5: VCN1 VGA Connector.............................................. 51
Table A.6: CN9 COM1 (RJ45) Connector.................................. 52
Table A.7: CN4 & CN5 USB port 1 & port 2............................... 52
Table A.8: BT1 CMOS battery ................................................... 52
Table A.9: CN10 CF socket ....................................................... 52
Table A.10:CN4 SATA daughter board connector...................... 53
Table A.11:RJ1 LAN1 Connector................................................ 53
Table A.12:RJ1 LAN1 Indicator .................................................. 53
A.5.1 M/D, PWR & IDE/Hot-swap LEDs............................................... 54

MIC-3392 User Manual xii
Appendix B Programming the Watchdog Timer .55
B.1 Watchdog Timer Programming Procedure ............................................. 56
Appendix C CPLD .................................................. 57
C.1 Features.................................................................................................. 58
C.2 CPLD I/O Registers ................................................................................ 58
Table C.1: LPC I/O registers address ........................................ 58
C.2.1 Debug Message.......................................................................... 58
Table C.2: Debug_Code [7:0] (LPC I/O address: 80H).............. 58
C.2.2 Watchdog Register ..................................................................... 58
Table C.3: Watchdog [7:0] (LPC I/O address: 443H)................. 58
C.2.3 Watchdog Disable Register ........................................................ 59
Table C.4: Watchdog [7:0] (LPC I/O address: 444H)................. 59
Table C.5: Version [7:0] (LPC I/O address: 445H)..................... 59
C.2.4 Geography Address (GA) ........................................................... 59
Table C.6: GA [7:0] (LPC I/O address: 447H)............................ 59

Chapter 1
1Hardware
Configuration
This chapter describes how to
configure MIC-3392 hardware.

MIC-3392 User Manual 2
1.1 Introduction
The MIC-3392 is a high performance, power efficient CompactPCI single-board com-
puter based on the Intel Core 2 Duo and Core Duo microprocessors. The MIC-3392
delivers breakthrough energy-efficient performance for CompactPCI platforms. The
Intel Core 2 Duo provides enhanced energy-efficient performance to help equipment
manufacturers optimally balance processing capabilities within power and space con-
straints. The advanced smart cache of Core Duo dynamically allocates the shared L2
cache across cores and optimizes use of memory subsystem bandwidth to acceler-
ate out-of-order execution. A prediction mechanism reduces the time in-flight instruc-
tions have to wait for data. The new pre-fetch algorithms move data from system
memory into fast L2 cache in advance of execution.
The Core Duo combines the benefits of two high-performance execution cores with
intelligent power management features to deliver significantly greater performance
per watt over previous Intel processors. The two execution cores share a high-perfor-
mance, power-optimized 667 MHz front-side bus to access the same system mem-
ory. To save power, address and data buffers are turned off when there is no activity.
The MIC-3392 maximizes I/O throughput with PCI Express (PCIe) technology. It sup-
ports up to 4 GB of 667 MHz DDR2 memory provided by a combination of SO-DIMM
and soldered DRAM (6.4 GB/sec throughput). It supports a fast Serial-ATA interface
to an on-board hard drive or CompactFlash socket. The MIC-3392 is available in sin-
gle or dual PMC variants with differing I/O combinations as listed in the table below.
1.2 Specifications
1.2.1 CompactPCI Bus Interface
The MIC-3392 is compliant with PICMG 2.0 Rev. 3.0. It supports a 64-bit / 66 MHz or
33 MHz PCI bus for up to 8 compactPCI slots at 3.3 V or 5 V VIO. The MIC-3392 is
hot-swap compliant (PICMG 2.1) and conforms to the CompactPCI Packet Switching
Backplane specification (PICMG 2.16) as well as the CompactPCI System Manage-
ment Specification (PICMG 2.9).
The board can be configured as a system master or a drone board. In drone mode it
only draws power from the CompactPCI backplane and is not active on the Compact-
PCI bus. However, PICMG 2.16 is still fully supported in this mode.
Table 1.1: MIC-3392 Variants
Features 'A' model Single PMC 'B' model Dual PMC
LAN 2 1
COM 1 1
PMC 1 2
USB 2 -
VGA 1 -
CPU - -
On-board HDD 1 -
CF socket 1 1
SODIMM socket 1 1

3 MIC-3392 User Manual
Chapter 1 Hardware Configuration
1.2.2 CPU
The MIC-3392 supports the latest Intel Core Duo/Solo and Intel Core 2 Duo proces-
sor family with clock frequencies up to 2.16 GHz and a Front-Side Bus (FSB) up to
667 MHz.
Intel Core Duo processors are validated with the Mobile Intel 945GM/945GME
Express chipset. This chipset provides greater flexibility for developers of embedded
applications by offering improved graphics and increased I/O bandwidth over previ-
ous Intel chipsets, as well as remote asset management capabilities, and improved
storage speed and reliability.
Currently supported processors are listed in the table below. The Intel Core Duo con-
sists of two cores and up to 2 MB L2 cache shared by both cores. The Intel Core 2
Duo consists of two cores, up to 4 MB L2 cache shared by both cores.
1.2.3 Processor
1.2.4 BIOS
An 8 Mbit Firmware Hub (FWH) contains a board-specific BIOS that is designed to
meet industrial and embedded system requirements.
1.2.5 Chipset
The Mobile Intel 945GM Express / 945GME chipset provides excellent flexibility for
developers of embedded applications by offering improved graphics and increased I/
O bandwidth over previous Intel chipsets, as well as remote asset management
capabilities and improved storage speed and reliability. Features include an inte-
grated 32-bit 3D graphics engine based on Intel Graphics Media Accelerator 950
(Intel GMA 950) architecture.
The Mobile Intel 945GM Express/945GME chipset consists of the Intel 82945GM
Graphics Memory Controller Hub (GMCH) and Intel I/O Controller Hub 7-M (ICH7-
M). It delivers outstanding system performance through high bandwidth interfaces
such as PCI Express, Serial ATA and Hi-Speed USB 2.0.
Table 1.2: Intel Processors
Core speed Front-Side
Bus speed
L2 cache TDP Package
Core Duo (T2500) 2.0 GHz 667 MHz 2 MB 31 W FCPGA
LV Core Duo (L2400) 1.66 GHz 667 MHz 2 MB 15 W FCBGA
Core 2 Duo (T7400) 2.16 GHz 667 MHz 4 MB 34 W FCPGA
LV Core 2 Duo (L7400) 1.5 GHz 667 MHz 4 MB 17 W FCBGA
Note! Because power consumption and thermal restrictions vary between dif-
ferent CompactPCI systems, please double check these items before
installing a higher speed CPU not listed in the table above.

MIC-3392 User Manual 4
1.2.6 Memory
The MIC-3392 has up to 2 GB of onboard non-ECC DDR2 memory. In addition, an
SODIMM socket supports up to 2 GB of the following types of memory.
Table 1.3: SODIMM Types (Non-ECC)
Brand Size Speed Vendor PN Memory
UG 512 MB DDR2 533 UG64T6400L8SU-
5AS
SEC 525 ZC05 K4T51083QC
EDE406CB (64x8)
Transcend 256 MB DDR2 533 119697-0060 SAMSUNG 52B K4T56083QF-
ZCD5 BBE393BA (32x8)
512 MB DDR2 533 119833-0266 Infineon HYB18T512 800AF37
SVV39006 0526 (32x8)
1 GB DDR2 533 120048-0014 ELPIDA TWN E5108AE-5C-E
0517A9105 (64x8)
DSL 256 MB DDR2 533 NA ELPIDA JAPAN E5116AB-5C-E
05020W108 (32x16)
512 MB DDR2 533 NA ELPIDA JAPAN E5116AB-5C-E
(32x16)
1 GB DDR2 533 NA ELPIDA TWN E5108AE-5C-E
0511009276 (64x8)
NEXS 512 MB DDR2 533 NXBS64M64VJ-75 ELPIDA TWN E5108AE-5C-E
0525A9B1S (64x8)
1 GB DDR2 533 NXBS128M64VJ-75 ELPIDA TWN E5108AE-5C-E
0525A9B1S (64x8)
Apacer 256 MB DDR2 533 78.82054.420 ELPIDA JAPAN E5116AB-5C-E
05050WPWA (64x8)
512 MB DDR2 533 78.92051.421 ELPIDA JAPAN E5108AB-5C-E
04520WR5Q (64x8)
1 GB DDR2 533 78.02051.423 ELPIDA TWN E5108AE-5C-E
(64x8)
A-DATA 256 MB DDR2 533 M20SS2F3G3410A1
BOZ
SAMSUNG 52B K4T56083QF-
GCD5 (32x8)
512 MB DDR2 533 M20EL2G3H3410A1
BOZ
ELPIDA JAPAN E5108AB-5C-E
(64x8)
1 GB DDR2 533 M20EL2G314430B1
BOZ
ELPIDA TWN E5108AE-5C-E
(64x8)
Transcend
(RoHS)
256 MB DDR2 667 TS32MSQ64V6M Infineon HYB18T512161BF-28
(32x16)
512 MB DDR2 667 TS64MSQ64V6J SAMSUNG K4T51083QC ZCE6
(64x8)
2 GB DDR2 667 TS256MSQ64V6U Micron 7GEIID9HNL
1 GB DDR2 667 TS128MSQ64V6J SAMSUNG K4T51083QC ZCE6
(64x8)
Apacer
(RoHS)
512 MB DDR2 667 78.92G63.422 ELPIODA E5108AG-6E-E (64x8)
1 GB DDR2 667 78.02G63.423 ELPIODA E5108AGBG-6E-E
(64x8)
DSL
(RoHS)
256 MB DDR2 667 NA ELPIDA E5116AF-6E-E (32x16)
512 MB DDR2 667 NA ELPIDA E5108AGBG-6E-E (64x8)
1 GB DDR2 667 NA ELPIDA E5108AGBG-6E-E (64x8)
UG
(RoHS)
512 MB DDR2 667 UG64T6400L8SU-
6AS
ELPIDA E5108AE-6E-E (32x16)
1 GB DDR2 667 UG12T6400L8SU-
6AP
ELPIDA E5108AG-6E-E (32x16)

5 MIC-3392 User Manual
Chapter 1 Hardware Configuration
1.2.7 Ethernet
The MIC-3392 uses two Intel 82573E LAN chips to provide 10/100/1000Base-T
Ethernet connectivity (LAN1 & LAN2) and one Intel 82562GT LAN chip to provide 10/
100Base-T Ethernet connectivity (LAN3) via rear I/O. Optional settings for the source
of each individual Gigabit Ethernet port can be selected in the BIOS menu. These are
mutually exclusive and can be any one of:
!Front I/O (RJ-45)
!Rear I/O (Rear Transition Module)
!PICMG 2.16
1.2.8 Storage interface
The MIC-3392 supports two SATA interfaces and one IDE channel. The SATA1 inter-
face can be routed to an onboard 2.5" SATA hard disk drive or to the rear I/O module
via the J3 connector. The onboard SATA port is only available on the single PMC ver-
sion of the MIC-3392. The SATA2 interface is connected to the rear I/O module via
the J5 connector and is reserved for user customized designs. Currently, Advan-
tech's compatible RIO modules provide the SATA1 interface. The MIC-3392 also sup-
ports one IDE channel. The master is reserved for an onboard CompactFlash disk
drive (type 1). The slave is connected to a rear I/O module via the J3 connector.
1.2.9 Serial ports
One RJ-45 COM1 port (RS-232 interface) is provided on the front panel. A COM2
port is routed to a rear I/O module via the J5 connector.
1.2.10 USB port
Two USB 2.0/1.1 compliant ports with fuse protection are provided. Both ports are
routed to front panel connectors on the MIC-3392A (single-PMC board variant) and
to the rear I/O module via the J5 connector on both the single-PMC and dual-PMC
board variants.
1.2.11 LEDs
LEDs are provided on the front panel as follows:
!One bi-color LED (blue/yellow) indicates hot-swap status. Blue indicates that the
board may be safely removed from the system and yellow indicates HDD activ-
ity.
!One green LED provides power status and a further green LED indicates “Mas-
ter or Drone” mode. Green indicates that the board is in “Master” mode and
when the LED is off the board is in “Drone” mode.
1.2.12 Watchdog timer
An onboard watchdog timer provides system reset capabilities via software control.
The programmable time interval is from 1 to 255 seconds.
1.2.13 Optional Rear I/O Modules
A number of rear I/O modules are available with different I/O options:
!RIO-3310AE: 6U cPCI Rear I/O Module without SCSI
!RIO-3310S-A1E: 6U cPCI Rear I/O Module (Internal SCSI connectors)
!RIO-3310S-A2E: 6U cPCI Rear I/O Module (External SCSI connectors)

MIC-3392 User Manual 6
1.2.14 Mechanical and Environmental Specifications
!Operating temperature: 0 ~ 55° C (32 ~ 122° F)
!Storage Temperature: -20 ~ 60° C (-4 ~ 140° F).
!Humidity (Non-operating): 5 ~ 95% @ 60° C (non-condensing)
!Power Consumption: (Intel Core 2 Duo and 2 GB memory)
+5 V @ 7.16 A; +3.3 V @ 3.17 A; +12 V @ 0.40 A
!Board size: 233.35 x 160 mm (6U size), 1-slot (4 TE) wide
!Weight: 0.8 kg (1.76 lb)
!Shock: 20 G (operating); 50 G (non-operating)
!Random vibration: 1.5 Grms (operating), 2.0 Grms (non-operating)
1.2.15 Compact Mechanical Design
The MIC-3392 has a specially designed CPU heat sink to enable fanless operation.
Forced air cooling in the chassis is needed for operational stability and reliability.
1.2.16 CompactPCI Bridge
The MIC-3392 uses a PLX PCI-6254 (Hint HB6) universal bridge as a gateway to an
intelligent subsystem. When configured as a system controller, the bridge acts as a
standard transparent PCI-to-PCI bridge. As a peripheral controller it allows the local
MIC-3392 processor to configure and control the onboard local subsystem indepen-
dently from the CompactPCI bus host processor. The MIC-3392 local PCI subsystem
is presented to the CompactPCI bus host as a single CompactPCI device. Finally,
when the MIC-3392 is in drone mode, the PLX PCI-6254 is electrically isolated from
the CompactPCI bus. The MIC-3392 receives power from the backplane, supports
rear I/O and supports PICMG 2.16. Consult the PLX PCI-6254 (Hint HB6) datasheet
for more details. The PLX PCI-6254 PCI bridge provides the following features:
!PCI Interface
–Full compliance with the PCI Local Bus Specification, Revision 2.2
–Supports 3.3 V or 5 V VIO operation
–Concurrent local and CompactPCI bus operation
!Buffer Architecture
–Queuing of multiple transactions in either direction
–256 bytes of posted write (data and address) buffering in each direction and
256 bytes of read data buffering in each direction
!Configuration Register and Control/Status Registers (CSRs)
–Two sets of standard PCI configuration registers for local and CompactPCI
interfaces, accessible from either the local or CompactPCI interface
–Three 32-bit base address configuration registers mapping the CSRs
!Transaction Forwarding
–Three primary interface base address configuration registers for downstream
forwarding with programmable size and prefetch for all three address ranges
–Direct offset address translation for downstream memory and I/O transac-
tions
–Three secondary interface address ranges for upstream forwarding, with pro-
grammable size and prefetch for all three address ranges
Note! The operating temperature range of the MIC-3392 depends on the
installed processor and the airflow through the chassis.

7 MIC-3392 User Manual
Chapter 1 Hardware Configuration
1.2.17 I/O Connectivity
Front panel I/O is provided by two RJ-45 Gigabit Ethernet ports, one RJ-45 COM
port, two USB 2.0 ports, one VGA connector, and one PMC cutout. On the dual-PMC
version only one RJ-45 Gigabit Ethernet Port and one RJ-45 COM port are available
on the front panel due to the space taken by the second PMC cutout.
Onboard I/O consists of one IDE channel to a Compact Flash socket and additionally
on the single-PMC version of the MIC-3392, one SATA channel can be connected to
a 2.5" SATA HDD. Rear I/O connectivity is available via the following CompactPCI
connectors:
!J3: First SATA port, one IDE slave port, one floppy port, one printer port, and
two Gigabit Ethernet links to the backplane for PICMG 2.16.
!J5: Second SATA port, 10/100 LAN port, two USB ports (same ports as on the
front panel), one keyboard & mouse connector, two COM ports, a VGA port and
two Gigabit Ethernet LAN port for Rear I/O board.
The MIC-3392 provides two Gigabit Ethernet ports that can be routed to the front
panel, the rear transition module or the PICMG 2.16 packet switched backplane.
1.2.18 PMC (PCI Mezzanine Card) IEEE1386.1 Compliant
Additional I/O or co-processing functionality is supported by add-on PMC modules.
The MIC-3392 supports up to two PMC sites that are fully compliant with the
IEEE1386.1 PCI Mezzanine Card specification. PMC1 supports a 64-bit / 66 MHz
PCI bus interface whilst PMC2 supports a 32-bit / 33 MHz PCI bus interface. PMC1
supports 3.3 V VIO only, whereas PMC2 supports both 3.3 V and 5 V VIO.
The two-layer front panel design complies with IEEE 1101.10. Connectors are firmly
screwed to the front panel, and a shielding gasket is attached to the panel edge. This
reduces emissions and increases protection from external interference.
1.2.19 Hardware Monitor
Two Hardware Monitors (W83782D) are available to monitor critical hardware param-
eters. One is attached to the ICH7 and the other is connected to the Baseboard Man-
agement Controller (BMC) to monitor CPU temperature core voltage information.
1.2.20 Super IO
The MIC-3392 Super I/O device provides the following legacy PC devices:
!The serial port COM1 is connected to the rear I/O module or front panel
!The serial port COM2 is connected to the rear I/O module or BMC
!The parallel port is routed to the rear I/O module
!The FDD is routed to the rear I/O module
!The keyboard and mouse is routed to the rear I/O module
1.2.21 RTC and Battery
The RTC module keeps the date and time. On the MIC-3392 the RTC circuitry is con-
nected to a battery source (CR2032M1S8-LF, 3 V, 210 mAH).
1.2.22 IPMI
The MIC-3392 uses the Intelligent Platform Management Interface (IPMI) to monitor
the health of an entire system. A Renesas H8S/2167 microcontroller provides BMC
functionality to interface between system management software and platform hard-
ware. The MIC-3392 implements fully-compliant IPMI 2.0 functionality and conforms
to the PICMG 2.9 R1.0 specification. The IPMI firmware is based on proven technol-
ogy from Avocent. Full IPMI details are covered in Chapter 3.

MIC-3392 User Manual 8
1.2.23 HPET and IO/APIC
The MIC-3392's built-in south bridge, the ICH7, provides features to support High
Precision Event Timer (HPET) registers and I/O Advanced Programmable Interrupt
Controller (APIC). The ICH7 timer registers are memory-mapped in a non-indexed
scheme. The choice of address range will be selected by configuration bits in the
HPET. The ICH7 incorporates an APIC that can be used in either a uni-processor or
multi-processor system, like the standard ISA-compatible PIC used in a uni-proces-
sor system.
1.3 Functional Block Diagram
Figure 1.1 MIC-3392 functional block diagram