Advantech PPC-MB-610 Installation and operation manual

PPC-MB-610 Startup Manual 1
Before card installation, please ensure that the following
items have been included in your shipment:
1. 1 x PPC-MB-610 mini-ITX motherboard
2. 1 x COM cables (1 to 4 port DB9)
3. 1 x SATA cable
4. 1 x PPC-MB-610 startup manual
5. 1 x Warranty card
6. 1 x Thermal grease
7. 14 x COM port screws
8. 2 x M.2 packet screws
If any of these items are missing or damaged, contact your
distributor or sales representative immediately.
Note 1:  FordetailedPPC-MB-610specications,refer
to the latest product information provided on the
Advantech website (PPC-61X1C model).
Note 2:  AcrobatReaderisrequiredtoviewPDFles.The
Acrobat Reader software can be downloaded
from www.adobe.com/Products/acrobat/read-
step2.html (Acrobat is a trademark of Adobe).
PPC-MB-610 Mini-ITX Motherboard with Intel® Core™ i7/
i5/i3/Pentium®/Celeron® LGA 1151 CPU, DP/VGA, 5 COM,
6 USB, Dual LAN, PCIe x 16, and M.2 M Key & E key
Startup Manual
1. Insert the memory module into the memory slot at a 45
degree angle, as shown below. Ensure that the gold
ngersofthemodulearefullyinsertedintotheslot.
2. Once inserted, gently press the memory module into
the slot until the tabs snap into place, securing the
module in position.
45°
Installation GuidePacking List
For more information about this or other Advantech
products, visit our website at
http://www.advantech.com
For technical support and service, visit our support
website at
http://support.advantech.com
This manual is for PPC-MB-610, Rev. A1.
Part No. 2043776000
Printed in China
Edition 1
July 2020

2 PPC-MB-610 Startup Manual
Selected
M/B
PPC-MB-610
CPU
CPU
i7-8700/i7-
8700T
i5-8500/i5-
8500T
i3-8100/i3-
8100T
Pentium
G5400/
G5400T
Celeron
G4900/
G4900T
i7-
9700TE
i5-9500E/
i5-9500TE
i3-9100E/
i3-9100TE
Core NO. 6/6 6/6 4/4 2/2 2/2 8 6/6 4/4
Max
Speed
3.2GHz(up to
4.6GHz) /
2.4 GHz(up
to 4.0GHz)
3.0GHz(up to
4.1GHz) /
2.1 GHz(up
to 3.5GHz)
3.6/3.1
GHz
3.7 / 3.1
GHz
3.1 / 2.9
GHz
1.8
GHz(up to
3.8GHz)
3.0GHz(up
to 4.2GHz)/
2.2 GHz(up
to 3.6GHz)
3.1GHz(up to
3.7GHz)/ 2.2
GHz(up to
3.2GHz)
L3 Cache 12 / 12 MB 9 / 9 MB 6 / 6 MB 4 / 4 MB 2 / 2 MB 12 MB 9/9 MB 6/6 MB
TDP 65 / 35 W 65 / 35 W 65 / 35 W 54 / 35 W 54 / 35
W35 W 65/35 W 65/35 W
Chipset Q370
Memory 2 x 260-pin SODIMM DDR4 , 2666 MHz , up to 32 GB ( non-ECC )
Network
(LAN)
2 x 10/100/1000 Mbps Ethernet and 1 x intel® L219LM (support AMT 12.0 only for i7 & i5) , 1 x Intel i211
Rear I/O 1 x RS232/422/485 , 1 x RS232 , 1x DP1.2 , 1 x VGA , 6 x USB3.1 , 1 x Line-out , 1 x Mic-in
Internal
Connector
3 x RS232 , 1 x GPIO ( 8 channels ) , 2 x speaker , 1 x LED , 2 x USB 2.0 , 1 x LVDS , 1 x touch control , 2 x SATA 3.0 (
support RAID 0,1 ) , 1 x LPC (to support TPM2.0) ,
Watchdog
Timer
255timerintervals,congurableusingsoftware
Expansion
"1 x M.2 slot(2280 M key) for storage; 1 x M.2 slot (2230 E key) for wireless
1 x PCIex16 slot for riser card"
Dimensions
(W x H)
170 mm x 170 mm (6.69" x 6.69")
OS Support Microsoft® Windows 10 ( 64 bit ), Linux
Specications

PPC-MB-610 Startup Manual 3
The PPC-MB-610 motherboard features a number of
jumpersthatallowuserstocongurethesystemaccording
tospecicapplications.Thefunctionsofeachjumperand
connector are listed in the table below.
Connector and Headers
Connectors and Headers List
Label Function
CN2 Mic-In/Line-Out connector
LAN2_USB1 RJ45+USB 3.1 stack connector
LAN1_USB1 RJ45+USB 3.1 stack connector
VGA1 VGA display connector
DP1 DisplayPort connector
COM12 COM 1/2 connector
USB3 USB 3.1 x2 connector
ATX12v1 ATX 12V power supply connector
CN21 ATX Power Supply Connector
CN5 Power button connector
CN6 COM 3/4/5 and GPIO connector
BAT1 Battery connector
SPI1 SPIBIOSashsocket
CN16 Touch connector
CN17 LVDS panel connector
CN20 LVDS backlight inverter power connector
Sysfan1 ~ 2 System fan power connector
CPUFAN1 CPU fan power connector
SATA1 ~ 2 SATA signal connector
CN4 Power LED connector
CN9/CN12 2 x USB 2.0 pin header
PCIEX16_1 PCIe x 16 slot connector
AMP1 Audioamplieroutputconnector
DIMMA1/
DIMMB1 DDR4 SODIMM socket
CPU1 CPU socket
M.2_2 M.2 E-Key
NGFF1 M.2 M Key
COM12: COM 2 Connector
Pin Denition
(RS232)
Denition
(RS422)
Denition
(RS485)
1DCD TX- TX RX-
2RXD TX+ TX RX+
3TXD RX+
4DTR RX-
5 GND
6 DSR
7RTS
8 CTS
9 RI
CN6:COM 3/4/5 and GPIO connector
1 COM3_DCD# 2 COM3_DSR#
3 COM3_RXD 4 COM3_RTS#
5 COM3_TXD 6 COM3_CTS#
7 COM3_DTR# 8 COM3_RI#
9 GND 10 GND
11 COM4_DCD# 12 COM4_DSR#
13 COM4_RXD 14 COM4_RTS#
15 COM4_TXD 16 COM4_CTS#
17 COM4_DTR# 18 COM4_RI#
19 GND 20 GND
21 COM5_DCD# 22 COM5_DSR#
23 COM5_RXD 24 COM5_RTS#
25 COM5_TXD 26 COM5_CTS#
27 COM5_DTR# 28 COM5_RI#
29 GND 30 GND
31 GND 32 SIO_GPIO6
33 SIO_GPIO4 34 SIO_GPIO2
35 SIO_GPIO0 36 SIO_GPIO7
37 SIO_GPIO5 38 SIO_GPIO3
39 SIO_GPIO1 40 +V5_DUAL
Jumpers and Connectors (Cont.)
Jumpers and Connectors

4 PPC-MB-610 Startup Manual
Jumper Settings
Jumpers List
Jumper Function
JP1 ATX/AT select
JCMOS1 RTC select
JP2 Touch power select
JP3 LCD power select
JP4 Enable power select
JP5 LVDS PWM power select
JP6 COM Pin 9 power select (COM 1 and 2)
JP7 LVDS resolution select
ATX/AT Select (JP1)
(1-2) P1 AT
(2-3) P2 ATX (default)
P1 P2
RTC Select (Jcmos1)
(1-2) P3 Normal (default)
(2-3) P4 Clear CMOS
P3 P4
CN16: Touch Connector
Pin Denition
1 Y+
2 X+
3 SENSE
4Y-
5 X-
Sysfan 1 ~ 2: System Fan Power Connector
Pin Denition
1 GND
2 POWER
3 SPEED
4 PWM
CPUFAN1: CPU Fan Power Connector
Pin Denition
1 GND
2 POWER
3 SPEED
4 PWM
CN4: Power LED Connector
Pin Denition
1 +V5_DUAL
2 +V5
3 GND
4 GND
AMP1: Audio Amplier Output Connector
Pin Denition
1 SPK L-
2 SPK L+
3 SPK R+
4 SPK R-
Jumpers and Connectors (Cont.) Jumpers and Connectors (Cont.)

PPC-MB-610 Startup Manual 5
Touch Power Select (JP2)
(1-2) P5 connect resistive touch screen(default)
NC P6 not connect resistive touch screen
P5 P6
LCD Power Select (JP3)
(1-2) P7 +V5
(2-3) P8 +V3.3 (default)
P7 P8
Enable Power Select (JP4)
(1-2) P9 +V5
(2-3) P10 +V3.3 (default)
P9 P10
LVDS PWM Power Select (JP5)
(1-2) P11 +V5
(2-3) P12 +V3.3 (default)
P11 P12
Jumpers and Connectors (Cont.) Jumpers and Connectors (Cont.)
COM Ring Select (JP6)
(1-3)/(2-4)
P13/P14
COM 2/1 ring (default)
(3-5)/(4-6)
P15/P16
COM 2/1 5V
(7-9)/(8-10)
P17/P18
COM 2/1 12V
P13 P14
P15 P16
P17 P18
LVDS Resolution Select (JP7)
(1-2)/(5-6)/ (7-8)
P19
1024*768 (24 bit) (for PPC-6151C
chassis)
(1-2)/(7-8)P20 1280*1024 (24 bit) (for PPC-
6171C chassis)
(3-4)/(7-8) P21 1280*1024 (24 bit) (for PPC-
6191C chassis)
P19 P20 P21

6 PPC-MB-610 Startup Manual
Board Layout: Jumper and Connector Locations
USB3 COM12 DP1
VGA1
LAN1_USB1
LAN2_USB1
CN2
AMP1
CN4
PCIE X 16
CN9
CN12
DIMMA1
DIMMB1
SYS FAN2
SYS FAN1
CPU FAN1
CN20
JP3
JP4 JP5
CN17
JP2
CN16
JP1 JP7
CN21
ATX12V1
CN22
SATA1
SATA2
SPI1
CN6
CN5 BAT1 JP6
JCMOS1
CPU1
M.2_2
NGFF1

PPC-MB-610 Startup Manual 7
1.1 Entering the BIOS Setup Utility
When the power is turned on, press the <Del> button to
enter the BIOS setup screen.
Afterasettingiscongured,press<F4>tosaveandexit;
otherwise,thecongurationwillnotbesavedintheBIOS.
1.2 COM 2 Mode Selection (RS232/422/
RS485)
1. Accessthe“NCT6106DSuperIOConguration”item
fromthe“Advanced”tab.
2. Select“SerialPort2Conguration”.TheCOM2mode
canbeconguredviathe“SerialPort2Mode”item.
BIOS Setup Program
3. Selectthe“RS485”option.Autoowandtermination
resistors can be enabled or disabled.
1.3 H/W Monitor and Smart Fan Mode
Conguration
1. Accessthe“H/WMonitor”itemfromthe“Advanced”tab
to check the voltage temperature and fan speed.
1.4 LAN PXE Mode Selection
1. Accessthe“NetworkStackConguration”itemfromthe
“Advanced”tab.
BIOS Setup Program (Cont.)

8 PPC-MB-610 Startup Manual
2. Selectthe“Enabled”optionforthe“NetworkStack”
item.
1.5 Boot Option Filter
1. Accessthe“CSMConguration”itemfromthe
“Advanced”tab.Userscanselect“UEFIonly”or
“Legacyonly”for“BootOptionFilter”conguration.
2. ConguretheVideoandStorageitemsettingstomatch
theBootOptionFilterconguration.
BIOS Setup Program (Cont.) BIOS Setup Program (Cont.)
1.6 Graphics Conguration
1. Accessthe“SystemAgent(SA)Conguration”item
fromthe“Chipset”tab.
2. Clickonthe“GraphicsConguration”item.
3. Selectthe“LCDControl”item.

PPC-MB-610 Startup Manual 9
4. ThePrimaryIGFXBootDisplayitemcanbecongured
as“VBIOSDefault”,“DP”,“LVDS”,or“VGA”.
5. TheBrightnessModeControlitemcongurationisset
to“Chipset”bydefault.Thismeansuserscanadjustthe
system brightness via the OS brightness dimmer.
6. Accessthe“BrightnessManualControl”itemtoselect
from six brightness level options.
BIOS Setup Program (Cont.) BIOS Setup Program (Cont.)
1.7 Wake-On-LAN and Ring
1. Inthe“Chipset”tabclickthe“PCH-IOConguration”
itemtoaccess“PCIEWake”conguration.Selectthe
“Enabled”optiontoallowwake-on-LANfunction.
2. Inthe“Chipset”tabclickthe“PCH-IOConguration”
itemtoaccess“WakeonRing”conguration.Selectthe
“Enabled”optiontoallowwake-on-ringfunction.
1.8 AT and ATX Settings
Inthe“Chipset”tabclickthe“PCH-IOConguration”item
toaccessthe“RestoreACPowerLoss”item.Settheitem
congurationto“PowerOn”,“PowerO󰀨”,or“LastState”.