Advantech EVA-2310 Installation and operation manual

EVA-2310 LoRaWAN Temperature and Humidity Sensor
Startup Manual
Thank you for purchasing the EVA-2310 LoRaWAN Temperature
and Humidity Sensor. This quick start guide is intended to help
you deploy your new sensor. The guide contains basic
information on the power and application wiring. Should you
require additional instructions, please refer to the user manual.
EVA-2310 is designed for 2 3.6V AA Lithium Batteries
1 x EVA-2310 Sensor
1 x Quick start manual
1. EVA-2310 runs OTAA mode, please have the AppKEY,
AppEUI and DeviceEUI in the QR-Code below.
For more information on this and other Advantech products,
please visit our website at:
http://www.advantech.com
For technical support and service:
https://www.advantech.com/support/
The startup manual is for EVA-2310 product.
Printed in China
1st Edition
Nov 2023
2. Default EVA-2310 frequency plan definitions below for
reference
Uplink Frequency plan:
Common Name
Uplink Frequency Plan(MHz)
US915
903.9, 904.1, 904.3, 904.5,
904.7, 904.9, 905.1, 905.3
904.6(@BW500)
EU868
868.1, 868.3, 868.5, 867.1
867.3, 867.5, 867.7, 867.9
868.8(@FSK)
AU915
915.2, 915.4, 915.6, 915.8,
916.0, 916.2, 916.4, 916.6
915.9(@BW500)
AS923
923.2, 923.4
Downlink Frequency plan:
Common Name
Downlink Frequency Plan(MHz)
US915
923.3, 923.9, 924.5, 925.1,
925.7, 926.3, 926.9, 927.5(RX1)
923.3(RX2)
EU868
868.1, 868.3, 868.5, 867.1
867.3, 867.5, 867.7, 867.9 (RX1)
869.525 –SF12BW125 (RX2)
AU915
923.3, 923.9, 924.5, 925.1,
925.7, 926.3, 926.9, 927.5(RX1)
923.3(RX2)
AS923
923.2, 923.4 (RX1)
923.2 –SF10BW125(RX2)
3. Open the front cover and install 2 3.6V AA lithium
batteries on battery holder.
EVA-2310 Startup Manual 1
Overview
Quick Start
Input Power Requirement
Packaging List

4. Press the button for 3 seconds for powering on the
device. You will see the LED quick blink one time.
Once the device connect to your LoRaWAN Network
Server successfully, the LED will on for 5 seconds.
Note: Button and LED behavior below for reference.
Button Press
LED Behavior
Function
Quick Press
Quick blink for
one time
Force TX
Press for 3 secs
Quick blink for
one time
Power On
Press for 5 secs
Quick blink for
20 times
System off and
reset to default
-
On for
5 Seconds
OTAA Join
Success
5. Default data update cycle of EVA-2310 is 3600 seconds. You
can change the data update cycle directly from WISE-6610,
Advantech LoRaWAN Gateway, or via a downlink command
from your service.
6. EVA-2310 has 3 mounting style which includes wall mount,
magnetic mount and pole mount.
Wall Mount Magnetic Mount
Pole Mount
1. Please do keep this start manual securely since the information
of AppKEY, AppEUI and DeviceEUI shows in this manual only.
2. Keep the device dry. Rain, moisture, or any liquid might contain
minerals and thus corrode electronic circuits. If the device gets
wet, please dry it completely.
3. Do not use or store the device in dusty or dirty environment. It
might damage its detachable parts and electronic components.
4. Do not store the device under excessive heat condition. High
temperature can shorten the life of electronic devices, destroy
batteries, and deform or melt some plastic parts.
5. Do not store the device in places that are too cold. Otherwise,
when the temperature rises to normal temperature, moisture
will form inside, which will destroy the board.
6. Do not throw, knock or shake the device. Rough handling of
equipment can destroy internal circuit boards and delicate
structures.
7. Do not clean the device with strong chemicals, detergents or
strong detergents.
8. Do not apply the device with paint. Smudges might block in the
device and affect the operation.
9. Do not throw the battery into the fire, or the battery will
explode. Damaged batteries may also explode.
EVA-2310 Startup Manual 2
Caution