Advantech ICR-3201 Series Guide

Start Guide
ICR-3201, ICR-3211, ICR-3231
ICR-3232, ICR-3241

Start Guide
Safety Instructions
Please take care to following instructions:
•Use the router in compliance with national and international law and in compliance with
any special or additional restrictions regulating the use of the router in the various appli-
cations and environments.
•To avoid possible injury and/or damage to the device, observe the relevant provisions
and standards. Use only the original accessories as recommended. Unauthorized de-
vice or accessory modification, or using accessories that have not been approved can
result in router damage and/or violation of the regulations.
•Unauthorized device or accessory modification or using the accessories that have not
been approved can result in warranty termination.
•Do not open the router.
•Caution! The SIM card can be swallowed by small children.
•When connecting the device to a power supply do not exceed the defined voltage.
•Do not expose the router to extreme ambient conditions. Protect the router against dust,
moisture, and high temperature.
•It is recommended that you do not use the router at petrol filling stations. We recommend
observing local restrictions concerning the use of radio-based devices while working with
explosive material for example, at petrol filling stations, or in chemical plants.
•While using the router close to personal medical devices, such as cardiac pacemakers
or hearing aids, proceed with heightened caution.
•Operating the router too close to TV sets, radio receivers, personal computers, or tele-
phones can cause interference.
•It is recommended that you create a copy or backup of the important settings stored in
the memory of the router.
QSG-0006-EN, August 4, 2021 1Released in the Czech Republic

Start Guide
Product Disposal Instructions
The WEEE (Waste Electrical and Electronic Equipment: 2012/19/EU) direc-
tive was introduced to ensure that electrical/electronic products are recycled us-
ing the best available recovery techniques in order to minimize impact on the en-
vironment. This product contains high-quality materials and components which
can be recycled. At the end of it’s life this product MUST NOT be mixed with
other commercial waste for disposal. The device contains the battery. Remove
the battery from the device before disposal. The battery in the device needs to be disposed
apart accordingly. Check the terms and conditions of your supplier for disposal information.
Open Source Software License
The software in this device uses various pieces of open-source software governed by the
following licenses:
•GPL versions 2 and 3
•LGPL version 2
•BSD-style licences
•MIT-style licences
The list of components together with complete license texts can be found on the device
itself. See Licenses link at the bottom of the router’s main Web page (General Status) or point
your browser to this address (replace the DEVICE_IP string with real router’s IP address):
https://DEVICE_IP/licenses.cgi
This is a written offer valid for 3 years since the device purchase offering any third party
for a charge no more than the cost of physically performing source distribution, a complete
machine-readable copy of the corresponding source code on a flash drive medium. If you are
interested in obtaining the source, please contact us at:
[email protected]
Modifications and debugging of LGPL-linked executables:
The manufacturer of the device hereby grants the right to use debugging techniques (e.g.
decompilation) and making customer modifications of any executable linked with an LGPL
library for own purposes. Note these rights are limited to the customer’s own usage. No further
distribution of such modified executables and no transmission of the information obtained
during these actions may be done.
QSG-0006-EN, August 4, 2021 2Released in the Czech Republic

Start Guide
First Use
Before applying power to the router, connect all the components that you need for your
applications. A cross-shaped screwdriver is necessary to insert a SIM card.
Do not run the router without an antenna connected to the main antenna connector as the
energy from the transmission is effectively reflected by the open end and can damage
the equipment.
ICR-3201 routers are not equipped with a cellular module, which means that SIM card
slots and cellular antenna connectors are not available on the router.
1. Antenna
Use an SMA connectors to connect the antennas to the router, see the figure below. Con-
nect the main antenna to the ANT connector. The second diversity antenna can be connected
to the DIV connector to improve the quality and reliability of a wireless link.
2. SIM Card
The SIM card reader for two Mini SIM cards (2FF with size of 25.0 x 15.0 x 0.76 mm) is
located on the left side panel of the router. If you intend to use this device to communicate
over a cellular network, please place an activated data-provisioned SIM card into the SIM card
reader. Unscrew the SIM cards cover and push your SIM card into the SIM1 or SIM2 slot until
it clicks into place.
QSG-0006-EN, August 4, 2021 3Released in the Czech Republic

Start Guide
Disconnect the router from the power supply before handling the SIM card.
3. Power
The router requires an external DC power supply. The DC voltage required is between
+9 and +36 V DC. The router has built-in protection against reverse polarity without signaling.
Connect the power supply cable to the PWR connector on the front panel of the router, see
the figure below.
QSG-0006-EN, August 4, 2021 4Released in the Czech Republic

Start Guide
4. Ethernet
For an initial configuration, made in a web browser, connect a PC by an Ethernet cable to
the default LAN interface, use the ETH0 port, see the figure above. By default, this interface
has the following configuration:
Connector Purpose Default Setting
ETH0 LAN port (default)
Connect your PC to this port to get the
router web interface.
DHCP Server
IP Address: 192.168.1.1
NetMask: 255.255.255.0
Configuration
1. Configuring the Device Using the Web Browser
You can use a web browser running on your PC to get access to the router web interface.
Here you can perform router monitoring, configuration, and administration. First, connect
the PC to the default LAN interface as described in the Ethernet chapter. To get the router
interface, enter the https://192.168.1.1 address in a web browser. Please note that usage
of the HTTPS protocol for secure communication over the network is required.
By default, there is just the root user account created on the router. See the product
label on the router for its default password1. Log in to the web interface by the root user
and his password. See the configuration manual of the router for a detailed description and
examples of the router configuration.
After logging on to the device for the first time, we strongly recommend changing the
default password due to security reasons.
For security reasons, it is highly recommended to update the firmware of the router to the
latest version regularly. Downgrading the firmware to an older version than the production
version or uploading a firmware intended for a different device may cause the malfunction
of the device.
1If the label does not contain a unique password, use "root" string as the password.
QSG-0006-EN, August 4, 2021 5Released in the Czech Republic

Start Guide
2. Configuration Settings via WebAccess/DMP
Your router has been pre-installed with the WebAccess/DMP client. For its activation,
enable it in the router’s web interface (Customization -> User Modules -> WebAccess/DMP
Client). For more information see the configuration manual of your router.
The activated client periodically uploads router identificators, its configuration, and cel-
lular network statistics to the WebAccess/DMP server. If you have purchased a part
number ending with "-DMP", the DMP client is activated by default.
With the WebAccess/DMP client activated, you may configure the router from WebAc-
cess/DMP portal. Navigate your browser to https://www.wadmp.com.
If this is your first time, please self-sign-up with the site. If not, please log in with your
username and password. Once logged in, further assistance can be found at https://docs.
wadmp.com.
3. Restoring and Backing up the Router Configuration
If you reset the router, the current configuration will be replaced by the default factory
settings. We recommend you to back up the router configuration before resetting the device.
Refer to the configuration manual for more information.
Once the router boots up and the PWR LED starts blinking, you can restore the default
router configuration. To do so, press the RST button on the front panel of the router for more
than 4 seconds. After you press this button, all settings are reset to the default values, and the
router will reboot.
Support
All product-related manuals, documents, and software can be found and downloaded on
the web site at icr.advantech.cz/download address.
Hereby, Advantech Czech s.r.o. declares that the radio equipment type
ICR-3201 (versions with radio interface only), ICR-3211 and ICR-3231 is in compli-
ance with Directive 2014/53/EU.ICR-3201 versions without radio interface are in compliance
with the essential requirements and other relevant provisions of Directives 2014/30/EU and
2014/35/EU.
The full text of the EU Declaration of Conformity is available at the following internet address:
icr.advantech.cz/eudoc
QSG-0006-EN, August 4, 2021 6Released in the Czech Republic