Advent ADV100S User manual

ADV100S/ADV100P
Drop Down DVD Video Monitor
Installation Guide
OFF AUTOON
POWER PLAY STOP EJECT

IMPORTANT
An LCD panel and/or video monitor may be installed in a motor
vehicle and visible to the driver if the LCD panel or video monitor
is used for vehicle information, system control, rear or side ob-
servation or navigation. If the LCD panel or video monitor is used
for television reception, video or DVD play, the LCD panel or
video monitor must be installed so that these features will only
function when the vehicle is in ‘park’ or when the vehicle’s parking
brake is applied.
An LCD panel or video monitor used for television reception,
video or DVD play that operates when the vehicle is in gear or
when the parking brake is not applied, must be installed to the
rear of the driver’s seat where it will not be visible, directly or
indirectly, to the operator of the motor vehicle.

TOOLS REQUIRED:
#2 Phillips Screwdriver
#1 Phillips Screwdriver
Utility or Razor Knife or Shears
Wire Strippers
Upholstery Hook Tool (for removal of panels as necessary)
ElectricalTape
MaskingTape
Multimeter (to verify 12 volt DC and continuity: Do not use a test light or logic probe)
Marker–tomark headliner
Scribe (to mark trim ring if used)
Misc. Electrical Connectors (to connect to vehicle power source. Requirements will vary from vehicle to vehicle)
MATERIALS INCLUDED IN THIS PACKAGE:
1) ADV100S/ADV100P Video Monitor (1 pc)
2) TrimRing(1pc)
3) HardwarePackage:
♦#4x 5/16”Screws (8 pcs)
♦#8x5/8”SelfDrillingScrews (4pcs)
♦#8Washers (4 pcs)
4) RemoteControl(P/N136B3469)(1pc)
5) 2Pin Power WireHarness withchoke(P/N 112B3143) (1pc)
6) Dome Light Harness (P/N 112B3110) (1 pc)
-1-
1
5
4
3
2
6
OFF AUTOON
POW ER PLAY STOP EJ ECT
MENU
RETURN
A-B
REPEAT
SETUP
+
POWER
EJECT
DISPLAY
ANGLE
AUDIO
SOURCE
ZOOM
1
4
2
5
3
6
0
Enter

-2-
GENERAL INSTALLATION APPROACH:
1) Decide upon system configuration and options that will be installed (i.e.: what components, VCP,
Tuner, RF Modulator/external amp, remote headphones, DVD, etc.).
2) Review all manuals to become familiar with electrical requirements and hook ups.
3) Decide upon mounting locations of all components and method of mounting.
4) Prep the vehicle by removing any interior trim necessary to gain access to vehicle's wiring as well as
all areas where interconnecting wire harnesses will need to be located. If any access holes need to
be cut into the vehicle (headliner, other trim components etc.), this should be done now as well
(Refer to Page 3).
5) Route the wiring harnesses throughout the vehicle as necessary. (Refer to the Wiring Diagrams on
page 6 and 7 of this manual as well as the wiring instructions for the individual components and
accessory options being installed). Be sure that all wiring is protected from sharp edges and is
routed in such a manner that it will not be pinched when all components and interior trim are fully
installed. Be sure to leave enough slack in the wiring at each component to allow working room.
6) Remove all A/V system components from their packaging and place them loosely in the vehicle at
their respective locations.
7) Connect all components together (electrically) and verify proper operation of all system functions.
Note: This is best done BEFORE components have been permanently mounted.
8) After verifying proper operation of the system, proceed to mount each of the components.
9) When all components are mounted, recheck function of entire system again to ensure that no wiring
was pinched or connected improperly during final installation.

-3-
FULL SIZE CONSOLE INSTALLATION
There are several "full size" custom console available for selected vehicles. Some of these vehicles are
the Chevrolet Suburban, Ford Expedition, and Dodge Durango. These full size consoles incorporate
several additional features, and particularly useful if the vehicle you are installing this system into already
has an OEM overhead console in the headliner.
Refer to the installation manual that comes with the console itself for complete installation instructions.
VEHICLE PREPARATION:
1) Locate an accessory power source (+12v when key is in the ACC. and run positions, and 0v when key
is off). Generally, this wire can be found at the ignition switch or fuse-box.
2) The mounting method and location will vary from vehicle to vehicle, so this manual will only focus on
the installation of the video monitor and related console accessories.
3) Generally, the best location for the video monitor is where the vehicle's factory dome light is installed.
The monitor should be located in such a manner that it can be comfortably viewed by rear seat
passengers. NEVER INSTALLTHE MONITOR INAPLACE WITHIN THE DRIVER'S VIEW. THIS IS
NOT ONLY DANGEROUS, BUT IT ISALSO ILLEGAL.
4) Once the mounting location of the monitor has been determined, there may be additional preparation
work necessary, depending on the vehicle structure and installation method. Some of the steps that
may be required are:
A) Removal of the vehicle's dome light
B) The headliner may need to be trimmed using the trim ring as a template per the
drawing below.
C) If the trim ring will be used, it will have to be trimmed to fit the contour of the vehicle's
headliner. Refer to the "Trim Ring installation" section further on in this manual.

MINI CONSOLE INSTALLATION:
This page only covers special installation considerations for the mini-console installation.
If the video monitor is to be installed in a vehicle with the mini console, the console may need to be
trimmed to fit the contour of the vehicle headliner.
1) In this installation, the video monitor is mounted directly to the overhead cross-member in the roof
using the mounting screw bosses. These screw bosses should contact the cross-member di-
rectly (i.e.: no gap between the screw boss and the roof structure). Also, be sure that the screws
do not pierce the outer roof skin when fully fastened to the cross-member. The mini-console is
attached to the video monitor using the perimeter screw bosses. It is important that the screws
used in this installation are not overtightened, and that the video monitor and mini-console are
mounted in such a way that the assembly does not distort (or bend) when the mounting screws
are tightened. An alternate method is to use a piece of plywood (12"x9"x3/4"). First secure the
plywood block to the cross-member, then screw the monitor into the plywood. See the drawing on
page5.
2) It is best to mount the video monitor to the roof structure without the mini-console first. There
shouldbeagapbetweentheheadliner and the outer flangeofthevideomonitor. Themini-console
should be cut to full this gap. Apply masking tape to the outer surface of the mini-console in the
areas where the cut will be made.
3) Mark the cut to follow the necessary contour of the roof. The suggested method of marking is as
follows:
A) First mark the narrowest point of the mini-console on the masking tape. Be careful to
consider not only vertical location, but fore-aft location.
B) Using the handle of a screwdriver, make a “transfer marking tool”. See diagram below.
Place the tool against the roof and the marker against the masking tape on the mini-con-
sole. Trace the cut to be made around the entire perimeter of the mini-console.
C) Cut the mini-console using a sharp utility knife or shears. Make the cut in several passes
over the marked line, each time cutting a little deeper. It is not necessary to cut completely
through the plastic, the cut only need be over 50% of the wall thickness of the plastic. By
bending the cut back and forth several times, the plastic will break cleanly at the cut.
D) Check the fit of the trimmed console and make any minor adjustments necessary.
4) The mini-console can be painted or covered with a material that matches the headliner before
assembling the mini-console to video monitor.
5) Thefinishedmini-consoleshouldbeattached to the video monitor, then attachtheassemblytothe
roof.
Tape marker to screwdriver starting at
your mark for the lowest point,then
trace the contour of theroof
Cut Line
Headliner
Lowest Point Mark
Refer to Fig 7 for detail on atta
c
console to video pod and vide
o
vehicle structure.
Figure 6
Tape marker toscrewdriver. Startingat yourmark
for the lowest point, trace the contour of the roof
Lowestpoint mark
Cutline
Headliner
-4-

-5-
MOUNTING THE MINI-CONSOLE
#8x5/8" Self-Tapping
Screws
Roof
Roof Support
Headliner
12” x 9” x 3/4” Plywood
Block
Mini Console
Self-Tapping Screws
(not supplied)
Video Unit
#8 Flat Washer

-6-
ADV100S/ADV100P
1) Connect the Circular Mini-Din Connector of the source Component Harness into the 8 pin Din
Connector on the unit (sold seperately).
2) Connect the Power Harness to the mating connector on the Video Monitor.
3) Connect the power harness to the vehicle’s electrical system through an In-Line 5-Ampere fuse by
tapping into an accessory hot line.
4) Verify all functions of the System before final mounting of the finished assembly.
Power Harness
item #3
Red: +12VDC
A
ccessory Ckt.
(Install 5A
Inline Fuse)
Black: Ground
Red/Black (Lamp On)
Violet/Brown (Lamp Auto)
Black/Red (Lamp Common)
RCA FEMALE
CONNECTOR
VIDEO OUT (YELLOW)
RCA FEMALE
CONNECTOR
AUDIO OUT
LEFT (WHITE)
RCA FEMALE
CONNECTOR
AUDIO OUT
RIGHT (RED)
Dome Light Harness
item #5
RCA MALE
CONNECTOR
VIDEO IN (YELLOW)
RCA MALE
CONNECTOR
AUDIO IN (WHITE)
RCA MALE
CONNECTOR
AUDIO IN (RED)
Power
Connector 4 Pin
IR LED:
Clean the IR Receiver Window on the front of the VCP.
Remove Adhesive Backing and Apply IR LED to IR
Window on the Face of the VCP.
“Y” Adapter
for use with
Non-Stereo
Installations
ANT.IN
RF OUT OUT
FUSE
DC IN
A
ccessory
Harness
item #2
OPTIONAL

-7-
Red / black - Lamp on
Black / red - Lamp common
Violet / brown - Lamp Auto
To 12pin
connector
onMonitor
To
constant
+12vdc
To
constant
+12vdc FactoryDoorajar
switchor Body
Controlcomputer
Factory Dome light circuit
Positive Switched Dome lighting
CONNECTING THE DOME LIGHTS
The dome lights in the video monitor require three connections to the vehicle's wiring. There are two
common types of dome light circuits used, positive or negative switched. Positive systems supply volt-
age to the interior lights to turn them on, negative switched systems apply ground to illuminate the bulbs.
To determine which system you have you must locate the wires at the dome light. On a positive switched
system, with all the doors closed and the lights out, both wires at the dome light will rest at ground. When
the light is activated, one of these wires will switch to +12 vdc. This is the vehicle's switching wire. On a
negative switched system, with all the doors closed and the lights out, both wires at the dome light will
rest at + 12vdc. When the light is activated, one of these wires will switch to ground. This is the switching
wire.
For positive systems, connect the violet / brown (Lamp auto) wire to the vehicle's switched wire. Then
connect the red / black (lamp on) wire to a fused constant 12 volt source and the black / red (lamp
common) wire to a good ground. Positive systems are commonly found on Ford vehicles.
For negative systems, connect the violet / brown (Lamp auto) wire to the vehicle's switched wire. Then
connect the red / black (lamp on) wire to a good ground and the black / red (lamp common) wire to fused
constant 12 volt source. Negative systems are commonly found on General Motors and import vehicles.
Note:
Some vehicles which incorporate transistorized control of the dome light circuit, such as the 1999 Dodge
Caravan, may require that the violet / brown (Lamp auto) wire be connected to the door pin switch
wire, as the additional current draw of the Monitor's lights may not be supported by the output of the
vehicles body control computer.

Troubleshooting:
SYMPTOM:
No power at Video Monitor
Power but no video or
sound
Picture, but no sound
No Infrared remote func-
tions for VCP (or other com-
ponents)
REMEDY:
-Verify +12 VDC onRedwireat2pinPower Harness behind video monitor.
Verify ground connection with continuity test from known good ground to
black wire at 2 pin Power Harness
-Verify that the correct source is selected (i.e.:1,2,3 or 4). Verify that the
source is on and playing a known good media (such as a DVD or video-
tape). Verify connections at both ends of the source component harness.
- Verify all connections per the wiring diagram on page 6 .
-Check batteries in the hand held remote. Verify that the IR LED ( page 6
Wiring Diagram) is properly attached to the sensor window of the VCP (or
other component).
Negative Switched Dome lighting
To12pin
connector
To
constant
To
constant
FactoryDoor ajar
switchorBody
Factory Dome light circuit
Red / black - Lamp on
Black / red - Lamp common
Violet / brown - Lamp Auto
-8-

This page blank intentionally

128-7317
© Copyright 2005 Advent 150 Marcus Blvd. Hauppauge, NY 11788
WWW .audiovox.com
For Customer Service
Visit Our Website At
Product Information, Photos,
FAQ’s Owner’s Manuals