Aeotec MULTISENSOR 6 User manual

AEOTEC Engineering Specification
Page 1 / 27
Engineering Specification
Doorbell 6
Document No.
SPEC-ZW162
Version
8
Description
This document mainly introduces AEOTEC new generation Doorbell 6. The content mainly includes
its appearance, features, certifications, quick start, and software function definition.
Doorbell 6 is a smart doorbell based on Z-Wave and 433.92MHz/FSK.
Not only a doorbell, but also can be used as a siren via setting its modes.
Supports pairing with 3 Buttons and can be controlled by 3 Buttons separately.
Built-in multiple tones, up to 30.
Designed as Multi Channel Device, including 1 Browse Endpoint, 3 Remote Endpoints, 2 Siren
Endpoints, and 1 Instant Endpoint, which enhances its application scenarios.
Written By
Hiking Chou
Date
2018-11-14
Reviewed By
Date
Approved By
Date

AEOTEC Engineering Specification
Page 2 / 27
REVISION RECORD
Doc. Rev Date
By
Pages affected
Brief description of changes
1
2018.10.26
Hiking
ALL
First revision
2
2018.10.29
Hiking
1, 19
Section 1.1 Abstract: add description about security requirement and
non-battery operated nodes within the network will act as repeaters.
Add new Section 1.4 Quick start.
Section 4.15 Configuration: modify the description of the value (0) about
Play Control of Parameter 0x02/0x03, changing to “Set but not play”
3
2018.11.01
Hiking
18,19,20
22
Modify the default Tone Index of Parameter 0x02~0x08
Parameter 0xFF: Add the precondition of ONLY reset to factory default
setting, and the precondition is “ If Size=1, Default=1, Value=0 ”
4
2018.11.05
Hiking
All
Move the Abstract info to the Home Page’s Description.
Add new Chapter 1 TERMINOLOGY DEFINITION
Add new Chapter 4 PRODUCT QUICK START, including
How to add Chime into Z-Wave network
How to remove Chime from Z-Wave network
How to factory reset Chime
How to factory reset Button
How to install Chime
How to install Button
How to pair Button
How to unpair Button
Modify the process description about pairing and unpairing Button.
5
2018.11.06
Hiking
All
Section 4.2: add description about security requirement and non-battery
operated nodes within the network will act as repeaters .
Modified some spelling and expression mistake.
Add hyperlinks to facilitate quick jumps
Modify “Keep the previous configuration” of Configuration Parameter
0x02/0x03, changing to “Use last valid configuration”
6
2018.11.07
Hiking
1
5
6
7
27
Home Page: Add “Approved by”
Chapter 1: Add the definition of “Ring Button”
Chapter 2: Update the picture
Chapter 3: Add “Indicator Light Power”, ”Tone Group Customization”
Add new Chapter 6 SAFETY CERTIFICATION
7
2018.11.08
Hiking
All
Modify Directory Outline
Merge features and safety certification into the same Chapter
Separate the appearance of the product as a page
8
2018.11.14
Hiking
Home Page
Modify the encoding format of “Document No.” in Home Page,
changing to “SPEC-Product Model”

AEOTEC Engineering Specification
Page 3 / 27
Table of Content
1INTERFACES & ACCESSORIES......................................................................................................................5
2FEATURES & CERTIFICATIONS.....................................................................................................................6
2.1 Features...........................................................................................................................................................6
2.2 Safety certifications .........................................................................................................................................7
3PRODUCT QUICK START.............................................................................................................................8
3.1 Important safety information..........................................................................................................................8
3.2 How to add Chime into Z-Wave network.........................................................................................................8
3.3 How to remove Chime from Z-Wave network.................................................................................................9
3.4 How to factory reset Chime.............................................................................................................................9
3.5 How to factory reset Button............................................................................................................................9
3.6 How to install Chime........................................................................................................................................9
3.7 How to install Button.....................................................................................................................................10
3.8 How to pair Button ........................................................................................................................................11
3.9 How to unpair Button....................................................................................................................................12
4SOFTWARE FUNCTION DEFINITION..........................................................................................................13
4.1 Function Overview.........................................................................................................................................13
4.2 User Behavior Interaction..............................................................................................................................13
4.3 Supplementary Explanation about Button....................................................................................................15
4.4 Tone Group Priority Definition.......................................................................................................................16
4.5 SDK, Library and Device Classes ....................................................................................................................16
4.6 Announced Command Classes in NIF............................................................................................................16
4.7 Basic Command Class mapping .....................................................................................................................17
4.8 Z-Wave Plus Info ............................................................................................................................................17
4.9 Manufacturer Specific ...................................................................................................................................17
4.10 Version...........................................................................................................................................................17
4.11 Multi Channel ................................................................................................................................................17
4.12 Sound Switch .................................................................................................................................................18
4.13 Notification....................................................................................................................................................18
4.14 Association groups information.....................................................................................................................19
4.15 Configuration.................................................................................................................................................22

AEOTEC Engineering Specification
Page 4 / 27
DOORBELL 6

AEOTEC Engineering Specification
Page 5 / 27
1INTERFACES & ACCESSORIES
Terminology
Description
Chime
A component based on Z-Wave and 433.92MHz/FSK technology, and it can be used to play
tone when triggered by Z-Wave Command or paired Button.
Please refer to Section 4.1 for details.
Button
A component based on 433.92MHz/FSK technology, and it can be used to wireless control
Chime to play tone.
Please refer to Section 4.3 for details.
Action Button
A button in Chime, and it can be used for networking, resetting, and pairing Button, etc.
Please refer to Section 4.2 for details.
Ring Button
A button in Button, and it can be used for wireless controlling Chime to play tone.
Please refer to Section 4.3 for details.

AEOTEC Engineering Specification
Page 6 / 27
2FEATURES & CERTIFICATIONS
2.1 Features
Parameter
Value
Product Identifier
ZW162
Dimensions
Chime: 76*76*38.5mm Button: 85*38*14mm
Weight
Chime: 100g Button: 35g
Color
Chime: White Button: White
Environmental
Requirements
Operating temperature: 32° to 104° F (0° to 40° C)
Relative humidity: 8% to 80%
Wireless Technology
Z-Wave (Between Chime and Gateway), 433.92MHz/FSK(Between Chime and Button)
Z-Wave Plus
Yes
Z-Wave Module
ZM5101
Z-Wave Version
6.71.03
Z-Wave Library Type
Enhanced 232 Slave
Z-Wave Device Type
Sound Switch
Z-Wave Role Type
Always On Slave
Security Class
Non-Security, S0, S2 Unauthenticated, and S2 Authenticated
Smart Start Compatible
No
Over The Air (OTA)
Yes
Multi Channel Device
Yes
Z-Wave Antenna Distance
30m (Indoor) /150m (Outdoor). Between Chime and Gateway.
Button Control Distance
120m (Barrier-free sight line distance). Between Chime and Button.
External Buttons
and Connectors
DC Port (x1) Action Button (x1) Ring Button(x1)
Input Voltage
Chime: Battery, 3.7V; Power Adapter, DC 5V/2A Button: Battery, 3V
Battery
Chime’s Battery:
Model: PT502035
Capacity: 400mAh
Detachable: No
Chargeable: Yes. Charging via Chime Power Adapter.
Endurance: 4 hours
Button’s Battery:
Model: CR2450
Capacity: 630mAh
Detachable: Yes
Chargeable: No
Endurance: 2 years
Power Consumption
Chime: IWORK < 80mA, ISTANDBY < 70mA
Button: IWORK < 20mA, ISTANDBY < 0.1uA
Indicator Light Power
2W
Indicator Light
Color Temperature
5500K
Splash, Water,
and Dust Resistant
Chime: Not Waterproof
Button: Rated IP55 under IEC standard 60529
Sensors
Vibration Sensor
Supported Paired Buttons
Max: 3
Tones Storage Size
16M
Supported Tones
Max: 30; Default: 30. No interface to replace the built-in tones. If want to change these
built-in tones, you need to contact us to customize.
Volume
Max: 105dB from 10cm away; 7 adjustable levels
Tone Group
Include 1 Browse Group, 3 Remote Group, 2 Siren Group, and 1 Instant Group.

AEOTEC Engineering Specification
Page 7 / 27
Tone Group Customization
Can custom different Tone Group Parameters with Configuration Set, including Tone Index,
Play Control, Play Mode, Volume, Light Effect Index, Interval Between 2 tones, Continuous
Play Count, Intercept The Length Of A Tone. Tone Name can’t be customized by user.
In the Box
Chime (x1) Button (x1) Manual (x1) Screws (x5) Chime Power Adapter (x1; Line Length=1.5m)
Chime wall mount plate (x1) Chime wall mount plate double-side tape (x1)
Button wall mount plate (x1) Button wall mount plate double -side tape (x1)
2.2 Safety certifications
(1) Chime safety certification
Country
Certification Item
Certification Standard
America
FCC ID
FCC PART 15C
FCC SDOC
FCC PART 15B
Europe
CE-EMC
EN55032,EN55035
CE-RED
EN301489-1/-3
EN300220
EN62311
CE-LVD
EN60950
Battery
EN62133
Australia
RCM
AS/NZS CISPR 32
AS/NZS CISPR 4268
IEC60950
(2)Button safety certification
Country
Certification Item
Certification Standard
America
FCC ID
FCC PART 15C
Europe
CE-RED
EN301489-1/-3
EN300220
EN62311
CE-LVD
EN60950
Australia
RCM
AS/NZS CISPR 4268

AEOTEC Engineering Specification
Page 8 / 27
3PRODUCT QUICK START
Terminology
Description
Inclusion
The process when a Z-Wave gateway is adding a Z-Wave device.
Please refer to Section 3.2 & Section 4.1 for details.
Exclusion
The process when a Z-Wave gateway is removing a Z-Wave device.
Please refer to Section 3.3 & Section 4.1 for details.
Pair
The process when a Chime is pairing a Button.
Please refer to Section 3.8 for details.
Unpair
The process when a Chime is unpairing a Button.
Please refer to Section 3.9 for details.
Tone Group
The function of Tone Group is closely related to Endpoint, and it can be user-defined,
including Tone Index, Play Control, Play Mode, Volume, Light Effect Index, Interval Between
2 tones, Continuous Play Count, Intercept The Length Of A Tone. Tone Name can’t be
customized by user.
Please refer to Section 4.1, 4.4 & 4.15(Configuration Parameter 0x02~0x08) for details.
Button Number
#1 Button is closely related to Chime Endpoint 2 and Configuration Parameter 0x21.
#2 Button is closely related to Chime Endpoint 3 and Configuration Parameter 0x22.
#3 Button is closely related to Chime Endpoint 4 and Configuration Parameter 0x23.
Please refer to Section 3.8, 4.3 & 4.15(Configuration Parameter 0x21~0x24) for details.
3.1 Important safety information
Please read this Engineering Specification carefully for correct and effective use.
Failure to follow the recommendations set forth by AEOTEC Limited may be dangerous or cause a violation of the law.
The manufacturer, importer, distributor, and/or reseller will not be held responsible for any loss or damage resulting
from not following any instruction in this guide or in other materials.
Doorbell 6 includes 2 separate components: Chime and Button. Chime is intended for indoor use in dry locations only.
Do not use in damp, moist, and/or wet locations. Button offers IP55 water protection and is suitable for outdoor use
without direct exposure to heavy and penetrative rain. Button is constructed with nylon; away from heat and do not
expose to flame.
Warning:
To prevent possible hearing damage, test only when wearing appropriate hearing protection.
Contains small parts; keep away from children.
3.2 How to add Chime into Z-Wave network
Chime supports Security 2 Command Class. While a Security S2 enabled Controller is needed in order to fully use the
security feature. Chime can be included and operated in any Z-Wave network with other Z-Wave certified devices from
other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters
regardless of vendor to increase reliability of the network.
1. Set your Z-Wave gateway into its 'Add Device' mode in order to add Chime into your Z-Wave system. Refer to the
gateway's manual if you are unsure of how to perform this step.
2. Power on Chime via the provided power adapter; its LED will be breathing White light all the time.
3. Click Chime Action Button once, it will quickly flash White light for 30 seconds until Chime is added into the network.
It will become constantly bright White light after being assigned a NodeID.
4. If your Z-Wave gateway supports S2 encryption, enter the first 5 digits of DSK into your gateway's interface if /when
requested. The DSK is printed on Chime's housing.

AEOTEC Engineering Specification
Page 9 / 27
5. If Inclusion fairs, it will slowly flash White light 3 times and then become breathing White light; repeat steps 1 to 4.
Contact us for further support if needed.
6. If Inclusion succeeds, it will quickly flash White light 3 times and then become off. Now, Chime is a part of your Z-
Wave home control system. You can configure it and its automations via your Z-Wave system; please refer to your
software's user guide for precise instructions.
Note:
If Action Button is clicked again during the network access process, the network access process will exit, at the same
time the Indicator Light will extinguish immediately, and then become breathing White light.
3.3 How to remove Chime from Z-Wave network
1. Set your Z-Wave gateway into its 'Remove Device' mode in order to remove Chime from your Z-Wave system. Refer to
the gateway's manual if you are unsure of how to perform this step.
2. Power on Chime via the provided power adapter; its LED will be off.
3. Click Chime Action Button 6 times quickly; it will bright White light, up to 2s.
4. If Exclusion fairs, it will keep off; repeat steps 1 to 3. Contact us for further support if needed.
5. If Exclusion succeeds, it will quickly flash White light 3 times and then become breathing White light. Now, Chime is
removed from Z-Wave network successfully.
3.4 How to factory reset Chime
If something happens to Chime, you may want to factory reset it. There are two way:
Long press Action Button more than 20s. Please refer to Section 4.2 for details.
Sending Configuration Set. Please refer to Configuration Parameter=0xFF for details.
3.5 How to factory reset Button
There is no way to factory reset Button. If something happens to Button, please try to re-power it. Contact us for
further support if needed.
3.6 How to install Chime
Chime and Button communicate wirelessly and can be installed up to 120 meters/393 feet apart. However, the wireless
range is reduced by interference from competing wireless signals, doors, and walls. Before installing Chime, test your
desired installation location for both Button and Chime first to ensure that a reliable wireless connection can be made
between the 2 parts.
1. Select an installation location for Chime. Do not yet install it.
2. Power on Chime via the provided power adapter.
3. Affix Chime in the desired installation location using the provided mounting plate.
a. Affix the mounting plate to the selected surface; affix it using either 3 × 20mm screws or double-sided tape.
b. Lock your Chime onto the mounting plate.

AEOTEC Engineering Specification
Page 10 / 27
3.7 How to install Button
Avoid exposing Button to direct sunlight where possible to avoid UV damage and reduced battery performance.
1. Select an installation location for Button. Do not yet install it.
2. Power on Button.
a. Remove the 2 screws from Button's rear to open its battery cover and install the provided CR2450 battery with the
positive (+) on top.
b. Replace the battery cover and the 2 screws.
3. Test the wireless connection by pressing Ring Button to trigger a doorbell alert. Select an alternative installation
location for Chime if the connection is poor.
4. Install Button.
a. Affix the mounting plate to the selected surface; affix it using either 2 × 20mm screws or double-sided tape.
b. Lock your Button onto the mounting plate.

AEOTEC Engineering Specification
Page 11 / 27
3.8 How to pair Button
There are two way to trigger pairing Button:
Manually quick click Chime Action Button.
With Configuration Set. Please refer to Configuration Parameter=0x24 for details.
Below is mainly about manually quick click Chime Action Button to trigger pairing Button.
1. Different click times will trigger pairing different Button. Please action as shown below.
Click Action Button 3 times quickly will trigger pairing #1 Button.
Click Action Button 4 times quickly will trigger pairing #2 Button.
Click Action Button 5 times quickly will trigger pairing #3 Button.
2. Observe the Indicator Light of Chime to make sure which Button is waiting for pairing.
When pairing #1 Button is triggered, it will bright 1 time ON 0.5s OFF 1s, and then become constantly bright White
light, indicating that pairing #1 Button has already triggered. Pairing time is up to 10 seconds. In this time period,
user MUST manually click Ring Button 3 times quickly.
When pairing #2 Button is triggered, it will bright 2 times ON 0.5s OFF 1s, and then become constantly bright White
light, indicating that pairing #2 Button has already triggered. Pairing time is up to 10 seconds. In this time period,
user MUST manually click Ring Button 3 times quickly.
When pairing #3 Button is triggered, it will bright 3 times ON 0.5s OFF 1s, and then become constantly bright White
light, indicating that pairing #3 Button has already triggered. Pairing time is up to 10 seconds. In this time period,
user MUST manually click Ring Button 3 times quickly.
3. Determine pairing results.
If pairing Button succeeds, Chime will quickly flash White light 3 times and play the corresponding tone of paired
Button once, and then become breathing White light (when Chime is out of the Z-Wave network) or off (when Chime
is in the Z-Wave network)
If pairing Button fairs, Chime will slowly flash White light 3 times and then become breathing White light (when Chime
is out of the Z-Wave network) or off (when Chime is in the Z-Wave network).
Each successful pairing will overwrite the previous paired Button which has the same Button Number.

AEOTEC Engineering Specification
Page 12 / 27
Note:
ONLY one Button can be paired at a time.
This manually quick click Action Button operation can ONLY be used to trigger pairing, not unpairing.
3.9 How to unpair Button
There is ONLY one way to trigger unpairing Button:
With Configuration Set. Please refer to Configuration Parameter=0x24 for details.

AEOTEC Engineering Specification
Page 13 / 27
4SOFTWARE FUNCTION DEFINITION
4.1 Function Overview
Function Item
Description
Inclusion
When the product is out of the network:
If a controller is requesting to add a product and the product enters the Learning
Mode with sending Node Info, the product will be added to the controller's network
with a NodeID assigned by the controller.
When the product is in the network:
If a controller in the network is requesting to add a product and the product enters
the Learning Mode with sending Node Info, the product will be added to the
controller's network again but the NodeID of the product will not change.
If a controller in another network is requesting to add a product and the product
enters the Learning Mode with sending Node Info, the product will NOT be added to
the controller's network.
Exclusion
When the product is out of the network:
If a controller is requesting to remove a product and the product enters the Learning
Mode with sending Node Info, the product will be removed from the controller's
network, and keep being out of the network.
When the product is in the network:
If a controller in the network is requesting to remove a product and the product
enters the Learning Mode with sending Node Info, the product will be removed from
the controller's network, and become out of the network.
If a controller in another network is requesting to remove a product and the product
enters the Learning Mode with sending Node Info, the product will be removed from
the controller's network, and become out of the network.
Factory Reset
Long press Action Button more than 20s. Please refer to Section 4.2 for details.
Sending Configuration Set. Please refer to Configuration Parameter=0xFF for details.
Power-down Memory
Remember the configuration information after the product is powered off.
Tone Play
Play the built-in tone with Sound Switch Tone Play Set, Basic Set, or Configuration Set.
Volume Adjustment
Adjust the volume with Sound Switch Configuration Set or Configuration Set.
Tone Group
Include 1 Browse Group, 3 Remote Group, 2 Siren Group, and 1 Instant Group.
Browse Group: Used for browsing the built-in tone, and can be triggered by Sound
Switch Tone Play Set, Basic Set, or Configuration Set.
Remote Group: Used for Button wireless control, and can be triggered by Sound
Switch Tone Play Set, Basic Set, or Configuration Set, as well as paired Button.
Siren Group: Cooperate with other nodes as a siren, and can be triggered by Sound
Switch Tone Play Set, Basic Set, or Configuration Set.
Instant Group: Used for continuous playback without pause, and can be triggered by
Sound Switch Tone Play Set, Basic Set, or Configuration Set.
Tone Group Customization
Can custom different Tone Group Parameters with Configuration Set, including Tone Index,
Play Control, Play Mode, Volume, Light Effect Index, Interval Between 2 tones, Continuous
Play Count, Intercept The Length Of A Tone. Tone Name can’t be customized by user.
Pair or Unpair Button
A Chime supports up to 3 Buttons at the same time, while a Button can support
multiple Chime at the same time.
There are two way to trigger pairing Button:
Manually quick click Chime Action Button. Please refer to Section 3.8 for details.
With Configuration Set. Please refer to Configuration Parameter=0x24 for details.
There is ONLY one way to trigger unpairing Button:
With Configuration Set. Please refer to Configuration Parameter=0x24 for details.
4.2 User Behavior Interaction
User behavior
Out of the Z-Wave network
In the Z-Wave network
Function
Indicator Light
Function
Indicator Light
Power OFF
NA
OFF
NA
OFF

AEOTEC Engineering Specification
Page 14 / 27
Power ON
Supply Power
When powered by battery, it will
be breathing White light for 30
seconds (max).
When powered by adapter, it
will be breathing White light all
the time.
Supply Power
White light for 2 seconds and
then become off.
Click Action Button
once
Send Node Info
for Inclusion
When click Action Button once,
it will quickly flash White light
for 30 seconds until Chime is
added into the network. It will
become constantly bright White
light after being assigned a
NodeID.
If Inclusion succeeds, it will
quickly flash White light 3 times
and then off. If Inclusion fairs, it
will slowly flash White light 3
times and then become
breathing White light.
If Action Button is clicked again
during the network access
process, the network access
process will exit, at the same
time the Indicator Light will
extinguish immediately, and
then become breathing White
light.
Stop playing
the sound and
light
Immediately OFF
Click Action Button
3 times quickly
Trigger pairing
#1 Button
It will bright 1 time ON 0.5s OFF
1s, and then become constantly
bright White light, indicating
that pairing #1 Button has
already triggered.
If pairing Button succeeds, it will
quickly flash White light 3 times
and then become breathing
White light. If pairing Button
fairs, it will slowly flash White
light 3 times and then become
breathing White light.
Trigger pairing
#1 Button
It will bright 1 time ON 0.5s
OFF 1s, and then become
constantly bright White light,
indicating that pairing #1
Button has already triggered.
If pairing Button succeeds, it
will quickly flash White light 3
times and then become off. If
pairing Button fairs, it will
slowly flash White light 3 times
and then become off.
Click Action Button
4 times quickly
Trigger pairing
#2 Button
It will bright 2 times ON 0.5s OFF
1s, and then become constantly
bright White light, indicating
that pairing #2 Button has
already triggered.
If pairing Button succeeds, it will
quickly flash White light 3 times
and then become breathing
White light. If pairing Button
fairs, it will slowly flash White
light 3 times and then become
breathing White light.
Trigger pairing
#2 Button
It will bright 2 times ON 0.5s
OFF 1s, and then become
constantly bright White light,
indicating that pairing #2
Button has already triggered.
If pairing Button succeeds, it
will quickly flash White light 3
times and then become off. If
pairing Button fairs, it will
slowly flash White light 3 times
and then become off.
Click Action Button
5 times quickly
Trigger pairing
#3 Button
It will bright 3 times ON 0.5s OFF
1s, and then become constantly
bright White light, indicating
that pairing #3 Button has
already triggered.
If pairing Button succeeds, it will
quickly flash White light 3 times
and then become breathing
Trigger pairing
#3 Button
It will bright 3 times ON 0.5s
OFF 1s, and then become
constantly bright White light,
indicating that pairing #3
Button has already triggered.
If pairing Button succeeds, it
will quickly flash White light 3
times and then become off. If

AEOTEC Engineering Specification
Page 15 / 27
White light. If pairing Button
fairs, it will slowly flash White
light 3 times and then become
breathing White light.
pairing Button fairs, it will
slowly flash White light 3 times
and then become off.
Click Action Button
6 times quickly
Reserved
Reserved
Send Node Info
for Exclusion
White light is on, up to 2s.
If Exclusion succeeds, it will
quickly flash White light 3
times and then become
breathing White light. If
Exclusion fairs, it will become
off.
Long Press Action
Button [1, 2s)
Reserved
Keep off from press to release.
Reserved
Keep off from press to release.
Long Press Action
Button [2, 5s)
Test the sound
and light of the
Browse Group
White light when press, and
display in the default sound and
light configuration of the
Browse Group when release.
Test the sound
and light of the
Browse Group
White light when press, and
display in the sound and light
configuration of the Browse
Group, based on Configuration
Parameter 0x02, when release.
Long Press Action
Button [5, 10s)
Reserved
Brighter White light when press,
and become off when release.
Reserved
Brighter White light when
press, and quickly flash White
light when release，indicating
start to test communication
quality between Chime and
Node 1.
At the end of the test, the
White light is on for 2 seconds.
If the communication quality is
Good or Great, it will quickly
flash White light 3 times and
then become off. If the
communication quality is
Weak, it will slowly flash White
light 3 times and then become
off.
Long Press Action
Button [10, 20s)
Reserved
Speedup flashing White light
when press, and become off
when release.
Reserved
Speedup flashing White light
when press, and become off
when release.
Long Press Action
Button [20, ∞)
Factory Reset
When the time reaches 20s, the
Factory Reset is performed no
matter it is pressed or released.
If Factory Reset succeeds, it
will quickly flash White light 3
times and then become
breathing White light.
Factory Reset
after sending
Device Reset
Locally
Notification
Report
When the time reaches 20s,
Factory Reset is performed no
matter it is pressed or
released. If Factory Reset
succeeds, it will quickly flash
White light 3 times and then
become breathing White light.
If Factory Reset fails, it will
become off when release.
4.3 Supplementary Explanation about Button
Function
Description
Wireless Control Chime
When click Ring Button once, Button can wireless control the corresponding paired Chime.
Pairing Chime
When click Ring Button 3 times quickly, Button can be paired to Chime while Chime
triggers pairing Button.
Sending Button Info to Chime
When re-power or click Ring Button, Button will send its Button ID, Battery Voltage and
Firmware Version to its corresponding paired Chime.
Automatic sleep
After sending Button Info to Chime, Button will sleep automatically for saving batter y life.
Low Battery Indicator Light
If #1 Button is low battery, Chime Indicator Light will repeat cycle
(ON 100ms OFF 5s)
If #2 Button is low battery, Chime Indicator Light will repeat cycle

AEOTEC Engineering Specification
Page 16 / 27
(ON 100ms OFF 100ms ON 100ms OFF 5s)
If #3 Button is low battery, Chime Indicator Light will repeat cycle
(ON 100ms OFF 100ms ON 100ms OFF 100ms ON 100ms OFF 5s)
Low Battery Indicator Light will be activated when Chime detects the corresponding
paired Button is low battery, and disappears after the battery returns to normal.
When the battery voltage of Button is lower than 2.8V, it is judged to be low battery.
When the battery voltage of Button restores to over 2.9V, it is judged to return to
normal.
Low Battery Indicator Light has the lowest priority among all light effects, that is, it
will be displayed when there is no other light effect.
The light effect of the 3 Buttons are different. When multiple Buttons is low battery
at the same time, the corresponding light effect of the Button with smaller Button
Number is displayed first.
4.4 Tone Group Priority Definition
(#1 Siren = #2 Siren) > (#1 Remote = #2 Remoter = #3 Remote) > (Browse = Instant)
Rule Description
Example
A Tone Group is triggered, and the triggered Tone Group
event is not released, if the other Tone Group event with
lower priority than the Tone Group is triggered at this
time, the Tone Group is maintained.
The #1 Siren Group is triggered and the Tone of #1 Siren Group
is not stopped. At this time, if the paired #1 Button is clicked
once, the Tone of the #1 Button Group will not be triggered,
and the Tone of the #1 Siren Group will be maintained.
A Tone Group is triggered, and the triggered Tone Group
event is not released, if the other Tone Group event with
higher priority or the same priority than the Tone Group
is triggered, it is immediately replaced by the new Tone
Group.
The #1 Remote Group is triggered and the Tone of #1 Remote
Group is not stopped. At this time, if the paired #2 Button is
clicked once, the Tone of the #1 Remote Group will be stopped,
and the Tone of the #2 Remote Group will be play immediately.
4.5 SDK, Library and Device Classes
The application is based on:
Parameter
Value
SDK
6.71.03
Library
Enhanced 232 slave
Role Type
Always On Slave (AOS)
Device Type
Sound Switch
Supported security keys
S0, S2_UNAUTHENTICATION, S2_AUTHENTICATION
4.6 Announced Command Classes in NIF
The application implements a number of mandatory and optional command classes.
Command Class
Version
Not added
Non-secure added
Securely added
Non-secure CC
Secure CC
ZWAVEPLUS_INFO
2
Support
Support
Support
VERSION
2
Support
Support
Support
CONFIGURATION
1
Support
Support
Support
MANUFACTURER_SPECIFIC
2
Support
Support
Support
ASSOCIATION_GRP_INFO
1
Support
Support
Support
ASSOCIATION
2
Support
Support
Support
POWERLEVEL
1
Support
Support
Support
MULTI_CHANNEL_ASSOCIATION
3
Support
Support
Support
MULTI_CHANNEL
4
Support
Support
Support

AEOTEC Engineering Specification
Page 17 / 27
DEVICE_RESET_LOCALLY
1
Support
Support
Support
TRANSPORT_SERVICE
2
Support
Support
Support
SECURITY
1
Support
Support
Support
SECURITY_2
1
Support
Support
Support
SUPERVISION
1
Support
Support
Support
FIRMWARE_UPDATE_MD
4
Support
Support
Support
NOTIFICATION
8
Support
Support
Support
SOUND_SWITCH
1
Support
Support
Support
4.7 Basic Command Class mapping
Basic Set Command (value) maps to Sound Switch Tone Play Set Command (Tone Identifier).
Basic Get Command maps to Sound Switch Tone Play Get Command.
Basic Report Command maps to Sound Switch Tone Play Report Command.
4.8 Z-Wave Plus Info
Parameter
Value
Z-Wave Plus Version
1
Role Type
5 (ZWAVEPLUS_INFO_REPORT_ROLE_TYPE_SLAVE_ALWAYS_ON)
Node Type
0 (ZWAVEPLUS_INFO_REPORT_NODE_TYPE_ZWAVEPLUS_NODE)
Installer Icon Type
0x2000 (ICON_TYPE_GENERIC_SOUND_SWITCH)
User Icon Type
0x2000 (ICON_TYPE_GENERIC_SOUND_SWITCH)
4.9 Manufacturer Specific
Parameter
Value
Manufacturer ID 1
0x03
Manufacturer ID 2
0x71
Product Type ID 1
EU=0x00, US=0x01, AU=0x02, CN=0x1D
Product Type ID 2
0x03
Product ID 1
0x00
Product ID 2
0xA2
4.10Version
Parameter
Value
Z-Wave Protocol Library Type
0x03
Z-Wave Protocol Version
0x05
Z-Wave Protocol Sub Version
0x03
Firmware 0 Version
ZM5101 Software Version MSB
Firmware 0 Sub Version
ZM5101 Software Version LSB
Hardware Version
0xA2
Number of firmware targets
0x00
4.11Multi Channel
Parameter
Value
Individual End Points
7
Aggregated End Points
0

AEOTEC Engineering Specification
Page 18 / 27
Dynamic
0
Identical
1
Generic Device Class
GENERIC_TYPE_AV_CONTROL_POINT
Specific Device Class
SPECIFIC_TYPE_SOUND_SWITCH
Command Classes
COMMAND_CLASS_ZWAVEPLUS_INFO
COMMAND_CLASS_SECURITY
COMMAND_CLASS_SECURITY_2
COMMAND_CLASS_SUPERVISION
COMMAND_CLASS_ASSOCIATION
COMMAND_CLASS_ASSOCIATION_GRP_INFO
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION
COMMAND_CLASS_NOTIFICATION
COMMAND_CLASS_SOUND_SWITCH
4.12Sound Switch
(1)Sound Switch Tones Number Report Command
Supported Tones = 10 (example)
(2)Sound Switch Tone Info Report Command (example)
Tone Identifier
Tone Duration
Name Length
Name
1
0x0014
8
1AMBUL~1
2
0x0001
8
2ALARM~1
3
0x0014
8
3POLIC~1
4
0x003A
8
4FIRE~1
5
0x000F
8
5GASLE~1
6
0x0003
8
6MODER~1
7
0x000B
8
7ELECT~1
8
0x0002
8
8CLASS~1
9
0x003C
8
9ARMIN~1
10
0x003C
8
10SECU~1
(3)Sound Switch Configuration Report Command
Parameter
Valid Value
Default Value
Volume
0..7
7
Default Tone Identifier
0..Supported Tones
1
Note:
Since the tones in the Chime may be changed according to customer requirements, the Supported Tones and the Tone
Info may be different. However, the difference will not affect the normal use of the application.
Besides, the Default Value of Volume and Default Tone Identifier in Sound Switch Configuration Report Command will
not be modified the initial defaults although the customer requests to change tones.
4.13Notification
Notification Type
Notification Events
Description
Home Security
0x07
State idle
0x00
Vibration event is inactive
Tampering, product cover removed
0x03
Vibration event is triggered
Power Management
0x08
State idle
0x00
Button’s battery comes back to normal
Replace battery soon
0x0A
Button’s battery is in low battery
Siren
0x0E
State idle
0x00
Chime alarm is inactive
Siren active
0x01
Chime alarm is triggered

AEOTEC Engineering Specification
Page 19 / 27
4.14Association groups information
Backwards compatibility for non-Multi Channel devices, forces the root device AGI table to contain all the association
groups mentioned in each of the endpoints AGI tables except from group 1, the Lifeline group.
Root device
ID
Name
Node count
Profile
Function
1
Lifeline
5
General: Lifeline
Send Device Reset Locally Notification when
Factory Reset.
Send Sound Switch Tone Play Report when Chime
is triggered to play tone.
Send Sound Switch Configuration Report when
the volume or default tone is changed.
Send Configuration Report (Parameter=0x24)
after finishing pairing or unpairing Button.
Send Notification Report(Type=0x0E;Event=0x01)
when Chime is triggered.
Send Notification Report(Type=0x0E;Event=0x00)
when Chime is inactive.
Send Notification Report(Type=0x07;Event=0x03)
when vibration sensor is triggered.
Send Notification Report(Type=0x07;Event=0x00)
when vibration sensor is inactive.
Send Notification Report(Type=0x08;Event=0x0A)
when Button’s battery is in low battery.
Send Notification Report(Type=0x08;Event=0x00)
when Button’s battery comes back to normal.
2
On/Off control
(Browse)
5
Notification: Siren
Mirror of endpoint 1, group 2
3
On/Off control
(Remote 1)
5
Notification: Siren
Mirror of endpoint 2, group 2
4
On/Off control
(Remote 2)
5
Notification: Siren
Mirror of endpoint 3, group 2
5
On/Off control
(Remote 3)
5
Notification: Siren
Mirror of endpoint 4, group 2
6
On/Off control
(Siren 1)
5
Notification: Siren
Mirror of endpoint 5, group 2
7
On/Off control
(Siren 2)
5
Notification: Siren
Mirror of endpoint 6, group 2
8
On/Off control
(Instant)
5
Notification: Siren
Mirror of endpoint 7, group 2
Endpoint 1
ID
Name
Node count
Profile
Function
1
Browse
via Lifeline
0
Notification: Siren
Send Sound Switch Tone Play Report when Chime
Browse Group is triggered to paly tone.
Send Sound Switch Configuration Report when
the volume or default tone of Browse Group is
changed.
Send Notification Report(Type=0x0E;Event=0x01)
when Chime Browse Group is triggered.
Send Notification Report(Type=0x0E;Event=0x00)
when Chime Browse Group is inactive.
2
On/Off control
(Browse)
5
Notification: Siren
Forward Basic Set with 0xFF to associated nodes in this
group when Chime Browse Group is triggered and
forward Basic Set with 0x00 to associated nodes in this
group when Chime Browse group comes back to
normal.
Endpoint 2

AEOTEC Engineering Specification
Page 20 / 27
ID
Name
Node count
Profile
Function
1
Remote 1 via
Lifeline
0
Notification: Siren
Send Sound Switch Tone Play Report when Chime
#1 Remote Group is triggered to paly tone.
Send Sound Switch Configuration Report when
the volume or default tone of #1 Remote Group is
changed.
Send Notification Report(Type=0x0E;Event=0x01)
when Chime #1 Remote Group is triggered.
Send Notification Report(Type=0x0E;Event=0x00)
when Chime #1 Remote Group is inactive.
Send Notification (Type=0x08; Event=0x0A) when
Chime #1 Button’s battery is in low battery.
Send Notification (Type=0x08; Event=0x00) when
Chime #1 Button’s battery comes back to normal.
2
On/Off control
(Remote 1)
5
Notification: Siren
Forward Basic Set with 0xFF to associated nodes in this
group when Chime #1 Remote Group is triggered and
forward Basic Set with 0x00 to associated nodes in this
group when Chime #1 Remote Group comes back to
normal.
Endpoint 3
ID
Name
Node count
Profile
Function
1
Remote 2 via
Lifeline
0
Notification: Siren
Send Sound Switch Tone Play Report when Chime
#2 Remote Group is triggered to paly tone.
Send Sound Switch Configuration Report when
the volume or default tone of #2 Remote Group is
changed.
Send Notification Report(Type=0x0E;Event=0x01)
when Chime #2 Remote Group is triggered.
Send Notification Report(Type=0x0E;Event=0x00)
when Chime #2 Remote Group is inactive.
Send Notification (Type=0x08; Event=0x0A) when
Chime #2 Button’s battery is in low battery.
Send Notification (Type=0x08; Event=0x00) when
Chime #2 Button’s battery comes back to normal.
2
On/Off control
(Remote 2)
5
Notification: Siren
Forward Basic Set with 0xFF to associated nodes in this
group when Chime #2 Remote Group is triggered and
forward Basic Set with 0x00 to associated nodes in this
group when Chime #2 Remote Group comes back to
normal.
Endpoint 4
ID
Name
Node count
Profile
Function
1
Remote 3 via
Lifeline
0
Notification: Siren
Send Sound Switch Tone Play Report when Chime
#3 Remote Group is triggered to paly tone.
Send Sound Switch Configuration Report when
the volume or default tone of #3 Remote Group is
changed.
Send Notification Report(Type=0x0E;Event=0x01)
when Chime #3 Remote Group is triggered.
Send Notification Report(Type=0x0E;Event=0x00)
when Chime #3 Remote Group is inactive.
Send Notification (Type=0x08; Event=0x0A) when
Chime #3 Button’s battery is in low battery.
Send Notification (Type=0x08; Event=0x00) when
Chime #3 Button’s battery comes back to normal.
2
On/Off control
(Remote 3)
5
Notification: Siren
Forward Basic Set with 0xFF to associated nodes in this
group when Chime #3 Remote Group is triggered and
forward Basic Set with 0x00 to associated nodes in this
group when Chime #3 Remote Group comes back to
normal.
Endpoint 5