AERMEC REMOTE HANDSET User manual

www.aermec.com
Translation from original
User manual
Q
REMOTE HANDSET
21.05 - 5390016_00

All specifications are subject to change without prior notice. Although every effort has been made to
ensure accuracy, Aermec shall not be held liable for any errors or omissions.
Dear customer,
Thank you for choosing an AERMEC product. It is the fruit of many years of experience and special
design studies and has been made of the highest grade materials and with cutting edge technology.
In addition, all our products bear the EC mark indicating that they meet the requirements of the
European Machine Directive regarding safety. The quality level is being constantly monitored, so
AERMEC products are synonymous with Safety, Quality and Reliability.
The data may undergo modifications considered necessary for the improvement of the
product, at any time and without the obligation for any notice thereof.
Thank you once again.
AERMEC S.p.A
This marking indicates that this product should not be disposed with other household
wastes throughout the EU.
To prevent possible harm to the environment or human health from uncontrolled disposal
of Waste Electrical and Electronic Equipment (WEEE), please return the device using
appropriate collection systems, or contact the retailer where the product was purchased.
Please contact your local authority for further details.
Illegal dumping of the product by the user entails the application of administrative
sanctions provided by law
INFORMATION FOR USER
This device is universal.
By pressing a key for a function that is not available, the unit will not change the operating status.
Never install the device in a damp area and do not expose it to direct sunlight.
Do not bump, throw or disassemble the device frequently.
Never use the device with wet hands.
Carefully read the manual before using and installing the device.

REMOTE CONTROL.................................................................................................................................................................................................................6
FUNCTIONS AVAILABLE THROUGH THE........................................................................................................................................................................8
REMOTE CONTROL.................................................................................................................................................................................................................8
SWITCHING THE UNIT ON OR OFF...................................................................................................................................................................................8
DEFINING THE OPERATING SETPOINT..........................................................................................................................................................................8
SELECTING AN OPERATING MODE..................................................................................................................................................................................9
SETTING THE VENTILATION SPEED ..............................................................................................................................................................................10
SETTING THE VERTICAL MOTORISED DELIVERY FIN SWING UP&DOWN................................................................................................... 11
SETTING THE HORIZONTAL MOTORISED DELIVERY FIN SWING LEFT&RIGHT.........................................................................................11
SETTING OR CANCELLING A PROGRAMMED SWITCHON TIMER ON ........................................................................................................12
SETTING OR CANCELLING A PROGRAMMED SWITCHOFF TIMER OFF.....................................................................................................12
ACTIVATING / DEACTIVATING THE PROLONGED VENTILATION XFAN FUNCTION............................................................................... 13
LIGHT FUNCTION  ENABLING/DISABLING THE INDOOR UNIT DISPLAY ..................................................................................................... 13
ACTIVATING / DEACTIVATING THE NIGHTTIME COMFORT FUNCTION........................................................................................................14
ACTIVATING OR DEACTIVATING THE WIFI FUNCTION ONLY WITH WIFI DEVICE INSTALLED ............................................................15
SETTING OR DISABLING THE BUTTON LOCK............................................................................................................................................................15
SETTING THE UNIT OF MEASUREMENT......................................................................................................................................................................16
ACTIVATING OR DEACTIVATING THE ENERGY SAVING FUNCTION.................................................................................................................16
COOLING MODE...................................................................................................................................................................................................................17
HEATING MODE....................................................................................................................................................................................................................17
REPLACING THE REMOTE CONTROL BATTERIES.....................................................................................................................................................18
INDEX
COMPANY CERTIFICATIONS
SAFETY CERTIFICATIONS

F
A
N
M
O
D
E
ON/OFF
SAVE
HEATCOOL
TIMERQUIET
SLEEP
LIGHT
X-FAN
E-HEATER
WiFi
4
6
8
10
12
1
3
5
7
9
2
2
11
13 14
15
16
17
6
• Some of the buttons of the remote control are not used
for this air conditioner, and are therefore not described in
these instructions. The pressing of these buttons will not
affect the operation of the air conditioner.
• Check there are no obstructions between the receiver and
the remote control.
• The maximum distance between the IR receiver and the
remote control for ensuring a good signal is 8 metres.
• Position the remote control at least 1 metre away from TVs,
radios, stereos, etc.;there may be some audio and video
interference.
• Do not drop or throw the remote control.
• Do not let liquids enter the remote control, and do not
leave it in direct sunlight or in hot places.
• When the indoor unit is powered, it will emit a sound
and the operating indicator will be activated. The air
conditioner can now be used, with the aid of the remote
control.
• When the remote control sends a signal, the symbol ,
appears on the display and the indoor unit receiver emits a
sound to confirm reception of the signal.
Index Function of the button:
1Switches the unit on or off
2
Increases or decreases the value of the
active function:
• Temperature
• Time
• ON timer
• OFF timer
3Selects the operating mode
4Sets the ventilation speed
5Activates or deactivates cooling mode
6Activates or deactivates heating mode
7Sets the operation of the motorised air
delivery fin (vertical swing)
8Sets the operation of the motorised air
delivery fin (horizontal swing)
9Activates or deactivates the QUIET
function
10
Activates or deactivates the SLEEP function
(this function is applicable to cooling
and heating mode); once activated, this
function will control the unit in order to
maintain an ideal temperature (which is
automatically calculated and cannot be set)
11
The indoor unit display shows the
temperature set-point and the room or
outside air temperature
12 Activates or deactivates the WIFI card
13 Activates or deactivates the TIMER mode
14 Activates or deactivates the X-FAN function
15 Activates or deactivates the energy saving
function SE
16 Liquid crystal display
17 IR transmitter
REMOTE CONTROL

F
A
N
M
O
D
E
ON/OFF
SAVE
HEATCOOL
TIMERQUIET
SLEEP
LIGHT
X-FAN
E-HEATER
WiFi
7
Icons available on the remote control display
Index Function represented by the icon:
Indicates that AUTOMATIC mode is
active
Indicates that COOLING mode is active
Indicates that DEHUMIDIFICATION mode
is active
Indicates that VENTILATION mode is
active
Indicates that HEATING mode is active
Indicates the current ventilation speed
Indicates that the setting has been
transmitted to the receiver on the indoor
unit
Indicates the battery charge level
Indicates that the WIFI function is active
Indicates that all display keys are locked
/ Indicates the unit of measurement for
the temperature set-points (°F or °C)
Indicates the temperature set as a
working set in the various modes
Indicates the system time, or the ON and
OFF timers
Indicates the system time, or the ON and
OFF timers
FUNCTION NOT AVAILABLE
Indicates the status of the horizontal
SWING function
Indicates the status of the vertical SWING
function
Indicates that the TURBO function is
active (the fan speed is forced by this
function)
FUNCTION NOT AVAILABLE
Indicates that the prolonged ventilation
function is active X-FAN
Indicates that the SLEEP function is
active
FUNCTION NOT AVAILABLE
FUNCTION NOT AVAILABLE

8
FUNCTIONS AVAILABLE THROUGH THE
REMOTE CONTROL
Switching on
All the operating modes (except automatic) require a
target ambient air temperature value; this is called the
operating set-point.
If the unit is on (and automatic mode is not selected),
press the or button to decrease or increase the
working set-point. The set-point value is displayed in
the central part of the remote control display.
Defining the operating set-point
F
A
N
M
O
D
E
ON/OFF
SAVE
HEATCOOL
TIMERQUIET
SLEEP
LIGHT
X-FAN
E-HEATER
WiFi
F
A
N
M
O
D
E
ON/OFF
SAVE
HEATCOOL
TIMERQUIET
SLEEP
LIGHT
X-FAN
E-HEATER
WiFi
By pressing the ON/OFF button it is possible to switch
the unit on or off. When off, some information is still
displayed on the remote control: the operating set-
point of the last operating mode used, and switch on
timers programmed (ON) and any icons tied to the
function active during the last switch on of the unit
(enabling the display of the indoor unit, etc.) Once
switched on the unit uses the settings selected during
the last operating session.
SWITCHING THE UNIT ON OR OFF
DEFINING THE OPERATING SETPOINT

9
If the unit is on, press the MODE button to pass from
one operating mode to the next, in the sequence
shown below. COOL, HEAT and FAN modes can also be
selected via the dedicated buttons (refer to the specific
paragraphs in this manual).
Selecting an operating mode
F
A
N
M
O
D
E
ON/OFF
SAVE
HEATCOOL
TIMERQUIET
SLEEP
LIGHT
X-FAN
E-HEATER
WiFi
SELECTING AN OPERATING MODE
DRY FAN HEATCOOLAUTO
The various operating modes have different features
and ranges:
• AUTOMATIC mode (AUTO): in this mode, the
remote control does not display any set-point value.
In AUTO mode the unit will automatically set the
temperature while the fan speed and the air outlet
angle can be adjusted
• COOLING mode (COOL) : in this mode the user
must set the operating set-point and a fan speed;
if the room temperature is higher than the set
value (which can be seen on the display), the air
conditioner will continue to cool the air until the
room temperature reaches the set-point value.
• DEHUMIDIFICATION mode (DRY): in this mode the
user must set the operating set-point but not the fan
speed (which remains fixed at minimum); if the room
temperature is higher than the set value (which
can be seen on the display), the air conditioner
will continue to dehumidify the air until the room
temperature reaches the set-point value.
• VENTILATION mode (FAN): in this mode the user
must only set the fan speed. This mode provides no
heating or cooling, using only the internal fan to
ventilate the room.
• HEATING mode (HEAT): in this mode the user must
set the operating set-point and a fan speed; if the
room temperature is lower than the set value (which
can be seen on the display), the air conditioner will
continue to heat the air until the room temperature
reaches the set-point value.
WARNING
To prevent cold air jets in heating mode, the
indoor unit will delay its operation for about 1-5
minutes (the actual delay time will depend on the
room temperature measured).

10
Press the FAN button to modify the fan speed. In DRY
mode (dehumidification), the fan will automatically
change to the minimum speed.
NOTE
• The Turbo FUNCTION is not available in DRY
or AUTO mode.
• Automatically activates QUIET speed when
the suspension function starts up.
• The unit works at low speed in DRY and AUTO
mode (the speed cannot be adjusted).
• In AUTO mode, the air conditioner will
automatically select the appropriate speed on
the basis of the room temperature.
AUTO
Automatic
Minimum speed
Medium speed
High speed
Turbo
AUTO
SETTING THE VENTILATION SPEED
Setting the ventilation speed
F
A
N
M
O
D
E
ON/OFF
SAVE
HEATCOOL
TIMERQUIET
SLEEP
LIGHT
X-FAN
E-HEATER
WiFi

11
If the unit is on, press the button to activate the
swing function of the motorised delivery fin. This fin
varies the direction of the flow of air into the ambient,
on the basis of the selected position. With the unit on,
press the and buttons to set the following steps,
one by one:
If the unit is on, press the button to activate the
swing function of the motorised delivery fin. This fin
varies the direction of the flow of air into the ambient,
on the basis of the selected position. With the unit ON,
press the and buttons to set the following steps,
one by one:
Continuous
swing
Continuous
swing (*)
Continuous
swing (*)
Fixed
(Step 1)
Fixed
(Step 1)
Fixed
(Step 2)
Fixed
(Step 2)
Fixed
(Step 3)
Fixed
(Step 3)
Fixed
(Step 4)
Fixed
(Step 4)
Fixed
(Step 5)
Setting the vertical motorised
delivery fin (swing)
Setting the horizontal motorised
delivery fin (swing)
F
A
N
M
O
D
E
ON/OFF
SAVE
HEATCOOL
TIMERQUIET
SLEEP
LIGHT
X-FAN
E-HEATER
WiFi
F
A
N
M
O
D
E
ON/OFF
SAVE
HEATCOOL
TIMERQUIET
SLEEP
LIGHT
X-FAN
E-HEATER
WiFi
SETTING THE VERTICAL MOTORISED DELIVERY
FIN SWING UP&DOWN
SETTING THE HORIZONTAL MOTORISED
DELIVERY FIN SWING LEFT&RIGHT
No
oscillation
Fixed
(Step 5)
No oscillation
(**)
WARNING
(*) there are different icons for continuous swing,
but all four of them activate the same mode:
continuous swing.
(**) although there are various icons that stop the
oscillation (fixed position steps), both the steps
indicated will deactivate oscillation mode.
LEFT&RIGHT
UP&DOWN
No oscillation
(**)

12
The unit has a timer for programming unit switch-on at
a specified time.
If the TIMER button is pressed while the unit is
switched off, you will access timer programming mode
(the HOUR and ON icons underneath the time will start
flashing). Press or to set the required switch-on
time. By keeping the TIMER button pressed for about 2
seconds, the time will move quickly on the display and
you will reach the required time faster.
Press TIMER again to confirm the time and activate the
programming. If you want to cancel a programmed
switch-on, just press TIMER again to delete it.
NOTE
• The time setting gap is from 0.5 to 24 hours.
• When making two operations (TIMER ON and
TIMER OFF), the time gap between them (with
no keys pressed) must not be more than 5
seconds. Otherwise, the programmed ON or
OFF operation will be automatically annulled.
• Once a programmed switch-on has been set,
the operating mode, working set-point and
fan speed will be the same as at the last unit
switch-off.
SETTING OR CANCELLING A PROGRAMMED
SWITCHON TIMER ON
Setting a programmed
switch-on
F
A
N
M
O
D
E
ON/OFF
SAVE
HEATCOOL
TIMERQUIET
SLEEP
LIGHT
X-FAN
E-HEATER
WiFi
TIMER ON
The unit has a timer for programming unit switch-off at
a specified time.
If the TIMER button is pressed while the unit is
switched on, you will access timer programming mode
(the HOUR and OFF icons underneath the time will start
flashing). Press or to set the required switch-off
time. By keeping the TIMER button pressed for about 2
seconds, the time will move quickly on the display and
you will reach the required time faster.
Press TIMER again to confirm the time and activate the
programming. If you want to cancel a programmed
switch-off, just press TIMER again to delete it.
SETTING OR CANCELLING A PROGRAMMED
SWITCHOFF TIMER OFF
Setting a programmed
switch-off
F
A
N
M
O
D
E
ON/OFF
SAVE
HEATCOOL
TIMERQUIET
SLEEP
LIGHT
X-FAN
E-HEATER
WiFi
TIMER OFF
NOTE
• The time setting gap is from 0.5 to 24 hours.
• When making two operations (TIMER ON and
TIMER OFF), the time gap between them (with
no keys pressed) must not be more than 5
seconds. Otherwise, the programmed ON or
OFF operation will be automatically annulled.
• once a programmed switch-on has been set,
the operating mode, working set-point and
fan speed will be the same as at the last unit
switch-off.

13
NOTE
the X-FAN function will remain active even after the
unit has been switched off via the remote control.
The icon will remain visible on the display to
indicate that the function is active.
During the operation in cooling or dehumidification
mode the condensate caused by the humidity in the air
is formed on the heat exchanger within the unit.
With the X-FAN function, the indoor unit fan carries
on working for a few minutes after unit switch-off to
completely dry the coil and avoid the formation and
proliferation of pathogens.
With the unit switched on, press the X-FAN/E-HEATER
button to activate or deactivate the function (only in
cooling or dehumidification mode).
The icon will appear on the remote control display
when the X-FAN function is active.
ACTIVATING / DEACTIVATING THE PROLONGED
VENTILATION XFAN FUNCTION
LIGHT FUNCTION  ENABLING/DISABLING THE
INDOOR UNIT DISPLAY
Setting the extended
ventilation function
Enabling the
info on the indoor unit
F
A
N
M
O
D
E
ON/OFF
SAVE
HEATCOOL
TIMERQUIET
SLEEP
LIGHT
X-FAN
E-HEATER
WiFi
F
A
N
M
O
D
E
ON/OFF
SAVE
HEATCOOL
TIMERQUIET
SLEEP
LIGHT
X-FAN
E-HEATER
WiFi
The display on the indoor unit must be activated using
the remote control. To activate the info on the front
panel of the indoor unit, press the LIGHT button on the
remote control.
To deactivate this function press the LIGHT button on
the remote controller again.

14
NOTE
The night-time comfort function is deactivated by
switching off the unit; it will not be active when
the unit is restarted. It can be activated at any
moment during the day.
The night-time comfort function controls the air
conditioner in an optimal way during the night. The
following logic is applied:
• In cooling or dehumidification: the temperature
set-point is gradually increased (no more than +3°C)
to guarantee maximum comfort combined with
energy savings.
• In heating: the temperature set-point is gradually
decreased (no more than -3°C) to guarantee
maximum comfort combined with energy savings.
If the unit is ON (and automatic or ventilation-only
mode is not selected), press SLEEP button to activate
or deactivate the night-time comfort function. If this
function is active, the icon will be displayed on the
remote control.
ACTIVATING / DEACTIVATING THE NIGHTTIME
COMFORT FUNCTION
Setting the night-time
comfort function
F
A
N
M
O
D
E
ON/OFF
SAVE
HEATCOOL
TIMERQUIET
SLEEP
LIGHT
X-FAN
E-HEATER
WiFi

15
Simultaneously press and buttons to lock and
unlock the keypad.
This function prevents any accidental changes to the
settings.
The icon on the remote control display shows that
the remote control keypad is locked.
With the unit switched on, press the WiFi button to
activate the WIFI device in the indoor unit.
The symbol on the remote control display
indicates that the device is active.
To deactivate the WIFI device, press the WiFi button for
at least 5 seconds; the icon will disappear from the
remote control display.
Resetting the WIFI module installed in the unit.
With the unit switched off, press the MODE and WiFi
buttons simultaneously for at least 1 second.
ACTIVATING OR DEACTIVATING THE WIFI
FUNCTION ONLY WITH WIFI DEVICE
INSTALLED
SETTING OR DISABLING THE BUTTON LOCK
Activating or deactivating the
WIFI function
Button lock
F
A
N
M
O
D
E
ON/OFF
SAVE
HEATCOOL
TIMERQUIET
SLEEP
LIGHT
X-FAN
E-HEATER
WiFi
F
A
N
M
O
D
E
ON/OFF
SAVE
HEATCOOL
TIMERQUIET
SLEEP
LIGHT
X-FAN
E-HEATER
WiFi

16
The unit display and the remote control display can
show the set temperature value in °C or °F. To change
the measurement unit, press the and MODE buttons
simultaneously while the unit is switched off.
The temperature value on the two displays will be
immediately converted.
Setting the unit of
measurement
F
A
N
M
O
D
E
ON/OFF
SAVE
HEATCOOL
TIMERQUIET
SLEEP
LIGHT
X-FAN
E-HEATER
WiFi
SETTING THE UNIT OF MEASUREMENT
The ENERGY SAVING function makes it possible to reach
the set temperature with lower energy consumption.
In COOLING mode
Press the SAVE button to set the ENERGY SAVING
function.
On the remote control display, the icon will appear
or disappear to indicate if the function is activated or
deactivated.
ACTIVATING OR DEACTIVATING THE ENERGY
SAVING FUNCTION
Activating or deactivating the
energy saving function
F
A
N
M
O
D
E
ON/OFF
SAVE
HEATCOOL
TIMERQUIET
SLEEP
LIGHT
X-FAN
E-HEATER
WiFi
NOTE
In ENERGY SAVING mode, the fan speed (set on
AUTO) and set temperature cannot be altered.
The SLEEP and ENERGY SAVING functions cannot
work at the same time.

17
Press COOL to activate cooling mode directly.
Press HEAT to activate heating mode directly.
Setting cooling
mode
Setting heating
mode
F
A
N
M
O
D
E
ON/OFF
SAVE
HEATCOOL
TIMERQUIET
SLEEP
LIGHT
X-FAN
E-HEATER
WiFi
F
A
N
M
O
D
E
ON/OFF
SAVE
HEATCOOL
TIMERQUIET
SLEEP
LIGHT
X-FAN
E-HEATER
WiFi
COOLING MODE
HEATING MODE

18
NOTE
• Remove the batteries if the remote control is
not used for a long time.
• The remote control can emit a signal up to a
maximum distance of 8 metres.
• The unit can be affected by signals
transmitted by the remote control units of
televisions, video recorders, or other devices
used in the same room.
WARNING
the battery charge level is shown on the remote
control. When the icon
ON/OFF
Light
I FeelFan
HeatCool
Sleep Wifi
X-Fan Temp
T-ON
Clock
Mode
T-OFF
INTELLIGENT
HOUR ON OFF
WIFI
flashes, replace the
batteries as otherwise the remote control cannot
work properly.
REPLACING THE REMOTE CONTROL BATTERIES
To replace the batteries of the infrared remote control,
proceed as follows:
1. Open the battery cover by sliding it in the direction
of the arrow.
2. Take out the old batteries
3. Insert new alkaline high-performance LR03 (AAA)
1.5V (penlight) batteries, being careful not to invert
the polarity.
4. Close the battery cover.
1.
2.
3.
4.

19

SCARICA L’ULTIMA VERSIONE: DOWNLOAD THE LATEST VERSION: TÉLÉCHARGER LA DERNIÈRE VERSION:
BITTE LADEN SIE DIE LETZTE VERSION HERUNTER: DESCARGUE LA ÚLTIMA VERSIÓN:
AERMEC S.p.A.
Via Roma, 996 - 37040 Bevilacqua (VR) - Italy
Tel. [phone] - Fax [phone]
[email protected] - www.aermec.com
SCARICA L’ULTIMA VERSIONE: DOWNLOAD THE LATEST VERSION: TÉLÉCHARGER LA DERNIÈRE VERSION:
http://www.aermec.com/qrcode.asp?q=16629 http://www.aermec.com/qrcode.asp?q=16630 http://www.aermec.com/qrcode.asp?q=16631
BITTE LADEN SIE DIE LETZTE VERSION HERUNTER: DESCARGUE LA ÚLTIMA VERSIÓN:
http://www.aermec.com/qrcode.asp?q=16632 http://www.aermec.com/qrcode.asp?q=16633
SCARICA L’ULTIMA VERSIONE: DOWNLOAD THE LATEST VERSION: TÉLÉCHARGER LA DERNIÈRE VERSION:
http://www.aermec.com/qrcode.asp?q=16629 http://www.aermec.com/qrcode.asp?q=16630 http://www.aermec.com/qrcode.asp?q=16631
BITTE LADEN SIE DIE LETZTE VERSION HERUNTER: DESCARGUE LA ÚLTIMA VERSIÓN:
http://www.aermec.com/qrcode.asp?q=16632 http://www.aermec.com/qrcode.asp?q=16633