AES WiFi Predator User manual

1 | P a g e
Installation Instructions
For
WiFi-Predator
PUSH Version
Manual version 3.4

2 | P a g e
Index
Section
Pages
Android Configuration
4-7
iPhone Configuration
8-13
Adding Additional Smart Phones & Devices
14
Range and range testing
15-17
Connecting via LAN cable
18
Installation
19
Power Supply
19
Wiring
20
Relay Output
21
Using on Android
21
Other options
22
Using on iphone
23
Other Options
24
Keypad Overview
25
Basic Keypad Programming
25
Full Keypad Programming
25
Using the Keypad
27
Troubleshooting
28
Revision Changes
31

3 | P a g e
Site Survey BEFORE you install..
YES!
I have at least a little wifi signal at the
gate with my phone.
(If not a repeater, bridge, powerline link or
Ethernet cable will be required).
Note: 802.11n type wifi networks have double
the range of 802.11b/g types!
YES!
Internet UPLOAD speed (not
download) is at least 1 Megabit per
second.
(If not then remote use is not recommended).
YES!
The WiFi network is WPA or WPA 2
type security.
(WEP is older, less secure protocol and will not
operate with this product).
IMPORTANT:
BENCH TEST & COMMISSION BESIDE ROUTER BEFORE
INSTALLATION

4 | P a g e
Open top screws only
Existing internet router
User phone
Android Configuration
IMPORTANT: The following process is only to be carried out with one device as
the master device. Do NOT repeat with additional devices. To add more phones or
tablets, see section on adding additional devices.
Step 1
Using one of the
homeowners’ Android
phones, search for
“Predator WiFi PUSH”, and
find the icon shown on the
Google Play store. Then
download and install the
PUSH version to the users
phone.
Step 2
Locate the intercom on a bench or table beside the home router, along with the user
phone. Connect the antenna & power supply provided to the intercom, red to +24v dc
and black to 0v dc, and power on.
Step 3
Wait a full 60 seconds for
the intercom to fully boot up.
Step 4
Press and hold the call
button for more than 3
seconds. A loud tone will be
heard. The intercom will now
be in configuration mode for
5 minutes.

5 | P a g e
Step 5
Enter settings on the
ANDROID phone, select
WiFi and scan for networks.
The phone should detect the
intercom.
The network name will be
BELL-XXXXX).
Select this network.
Step 6
Enter the following
DEFAULT password…
123456789. Now the phone
is connected directly to the
intercom which is now
broacasting its own wifi
network.
Step 7
Now open the WiFi-Predator
PRO App on the phone and
select as shown to add
intercom.
Step 8
Press SEARCH.

6 | P a g e
Step 9
The app should find the
intercom serial number.
Press as shown to select it.
Step 10
The app screen will now
show the intercom serial
number or BELL ID,
Username: admin
Password:LEAVE BLANK
Press DONE to confirm.
Step 10b
The phone and intercom should now be
DIRECTLY connected and display ONLINE
status. Press as shown and check that
there is video and audio.
IMPORTANT
If video and audio is working, then the product is working perfectly. Should you
have problems after this step, then it is likely either networking, setup or a range
issue. Consult technical support in such an event.
Step 11
The normal user screen should now appear
as shown. The status of the intercom should
now show ONLINE.
Press the SETTINGS button as shown.

7 | P a g e
Step 12
Select MANAGE WIFI NETWORK. The
intercom will now scan the area for available
networks.
Step 13
Select the wifi network which you would like
the intercom to connect to.
Step 14
Enter the wifi password and press DONE.
TIP: This unit will not work with older WEP
networks, only WPA and WPA2.
TIP: Ensure the password is correct. The app will
not know if the password is typed correctly or not.
Case sensitivity applies.
Step 15
Wait 1 minute. The intercom will now
disconnect from your phone, and attempt to
connect to the wifi network with the details
provided.
Step 16
If the connection is sucessful, the app
should re-connect and show status ONLINE.
You may now touch the banner as shown
and view video.
You are now ready to install the intercom in the location which it will be used!
Adding Additional Phones
Please jump to page 14 to see how to add additional smart phones or devices.

8 | P a g e
Open top screws only
Existing internet router
User phone
I-phone Configuration
IMPORTANT: The following process is only to be carried out with one device as the
master device. Do NOT repeat with additional devices. To add more phones or tablets,
see section on adding additional devices.
Step 1
Using one of the homeowners’
iphones, search for “Predator-WiFi
PRO” app on the Apple Store. Look
for the PRO icon shown. Then
download and install to the users
phone.
Step 2
Locate the intercom on a bench or table beside the home router, along with the user
phone. Connect the antenna & power supply provided to the intercom, red to +24v dc
and black to 0v dc, and power on.
Step 3
Wait a full 60 seconds for the
intercom to fully boot up.
Step 4
Press and hold the call button for
more than 3 seconds. The intercom
will sound a long tone, and now be in
configuration mode for 5 minutes.

9 | P a g e
Step 5
Enter settings on the apple device,
select WiFi and scan for networks.
The phone should detect the intercom.
The network name will be BELL-
XXXXX).
Select this network.
Step 6
Enter the following DEFAULT
password… 123456789.
Now the phone is connected directly to
the intercom which is now broacasting
its own wifi network.
Step 7
Now open the WiFi-Predator PRO App
on the phone and select as shown to
add intercom.
Step 8
Press SEARCH.
Step 9
The app should find the intercom serial
number. Press the banner and then
press DONE.

10 | P a g e
Step 10
The app screen will now show the
intercom serial number or BELL ID,
Username: admin
Password: LEAVE BLANK
Press DONE to confirm.
Step 10b
The phone and intercom should now be
DIRECTLY connected and display
ONLINE status. Press as shown and
check that there is video and audio.
IMPORTANT
If video and audio is working, then the product is working perfectly. Should
you have problems after this step, then it is likely either networking, setup or a
range issue. Consult technical support in such an event.
Step 11
The normal user screen should now
appear as shown. The status of the
intercom should now show ONLINE.
Press the SETTINGS button as shown.
Step 12
Select WIFI SETTINGS. The intercom
will now scan the area for available
networks.