AES 605 Instruction Manual

P a g e | 1
Installation & User Manual
For
605 D E C T + 2 . 4 G I n t e r c o m
Wireless Video Intercom System
Models 605AB, 605ABK

P a g e | 2
Contents
Overview of system
…………….Pg 3
Site Survey
…………….Pg 3
Mounting the Transmitter
…………….Pg 3
Power supply
…………….Pg 3
Mounting Architectural Panels
…………….Pg 4
Mounting Hooded Panels
…………….Pg 4
Mounting Flush Panels
…………….Pg 4
Wiring
…………….Pg 5
Code Lock Keypad Connections
…………….Pg 5
Wiring Tips
…………….Pg 6
Keypad Overview
…………….Pg 6
Basic Keypad Programming
…………….Pg 7
Full Keypad programming
…………….Pg 7
Using the Keypad
…………….Pg 9
The Handset
…………….Pg 9
Recoding / Adding a Handset
…………….Pg 9
Testing
.………….Pg 10
Using the Intercom Handset
.………….Pg 10
Maintenance of the Intercom
.………….Pg 10
Troubleshooting
.………….Pg 11

P a g e | 3
Overview of System
Please read this entire manual before attempting to install this system.
This system should only be installed by a professional automatic gate installer or access control
specialist installer.
It is recommended that the system be range tested on site BEFORE being fully installed.
Site Survey
Before installing this system, you need to be sure that the range of the system will be sufficient.
The transmitter and speech unit can be powered up, call button pressed, and then check that the
handset will ring from all areas in which it will be used.
Tip: For longer range installations, locate the handset close to the front of the property, near a
window if possible. Concrete walls can reduce the open air range of 350 metres by 30-50% per
wall.
Installation
Assuming satisfactory operation at full range, you are ready to fully install the product.
Mount the intercom at the desired height for pedestrian or car users. The camera angle
is wide at 90 degrees to cover most scenarios.
Loosen top 2 screws only
Hinge front door
Side View
Tip: Do not drill holes in the wall with the intercom in positon, otherwise dust may get
around the camera window and impair the camera view.

P a g e | 4
Mounting the Antenna
Mount the antenna as high as possible to achieve longest range.
TIP: Antenna beam width is approximately 40 degrees. For short range door
intercoms, ask your distributor or dealer for an omni-pole type antenna with 360 degree
beam angle.
Power Supply
TIP: Most technical calls received are due to installers using CAT5 or alarm cable
to power the unit. Neither are rated to carry enough power (1.5 amp peak). Please
use following cable sizes…
Up to 2 metres (6 feet) –Use minimum 0.75mm2(18 gauge)
Up to 4 metres (12 feet) –Use minimum 1mm2(16 gauge)
Up to 8 metres (24 feet) –Use minimum 1.5mm2(14 gauge)
Excessively long
cable!!
Power supply
Call point
Mains power Power supply
Call point

P a g e | 5
Wiring
Wiring Tips
Note: The manufacturer can only support the use, operation and functionality of the
intercom and keypad themselves. Professional wiring to door release or automatic gate
+-
N/C COM N/O N/C
Data I/O
N/O
egress
OUT1 OUT2
OUT3 N/C
COM
N/O K or A
Sense
Tamper
N/C
DU out
(-)GND
OUT2
Relay
Select N/ON/C

P a g e | 6
systems is the responsibility of the installer. Please consult a security integrator for
further support.
Advanced Keypad Connections
+-
N/C COM N/O N/C
Data I/O
N/O
egress
OUT1 OUT2
OUT3 N/C
COM
N/O K or A
Sense
Tamper
N/C
DU out
(-)GND
O/P1 inhib
INT Lock
OUT2
Relay
Select N/ON/C
12v DC
From Power
Supply
Keypad overview
This keypad has 3 outputs. The diagram below shows the LED indicators which indicate
programming and relay status information.
RED when incorrect codes entered and outputs are locked out.
1 2 3
4 5 6
7 8 9
* 0 #
SLOW FLASHING - in normal standby mode.
ON in programming mode.
ON when relay 3 activated.
GREEN when output 1 activated.
RED when output 2 activated.
CLEAR when output 3 activated
FAST FLASHING –Wrong code entered / error.
TIP: After power up, as a security precaution, the keypad cannot be programmed for 60 seconds.
Once this time elapses, you may begin.
TIP: Flashing amber LED is normal standby mode!
Advanced connections
INT Lock –Used to operate a door in conjunction with
another keypad. 24v dc max voltage, 100mA sink.
O/P1 inhib –When closed, this disables all codes for
relay group 1.
Sense –N/C connected to (-)GND, to be connected to
N/C door contact. Can be used to generate door open or
tamper alarm.
DU out –switches to (-) ground after the Duress Code is
entered. Used to trigger alarm zone, or buzzer to notify
guard. 100mA sink, 24VDC.
K or A –Not used.
DATA I/O PORT (Data Communication Bus) The Data I/O port is
prepared for setting up a data bus for the connection of the auxiliary reader-
keypads and the split-decoder in system expansion

P a g e | 7
Basic Keypad Programming
0 0 0 0 * *
Quick start guide
1) Enter programming mode (amber LED should be ON)
1 0 2 0 0 ? ?? ? #0
2) Enter a new user code...
* *
3) Exit programming mode
4) Enter the new user code to check the relay clicks.
Full Keypad programming
Enter programming mode..
0 0 0 0 * *
Exit programming mode..
* *
Enter a new ENGINEERS code…
Go into programming mode firstly then enter the following sequence…
Location
0 1 ?? ? ?
4-8 digit code Validate
#
Enter or delete new user codes
There are 3 groups of user codes. Group 10 for relay 1, group 20 for relay 2, and group 30 for
relay 3. The programming sequence is shown below…
Memory locations
000-999 for relay 1
001-100 for relay 2
001-100 for relay 3
1 0 2 0 0
10= relay 1 codes
(1000 available)
20= relay 2 codes
(100 available)
30= relay 3 codes
(100 available)
? ?? ? #0
2= add code
5= delete code Pin code 4-8 digits Validate
Example: Add user 31 to have access code 5555 operating relay 2….
2 0 2 0 3 5 55 5 #1
Group 2 Add code Location 31 Pin code 5555 Validate
Programming relay output times and modes…
Tip: The engineer code
must be the same length as
user codes. So if using a 6
digit engineers code, then
user codes must also be 6
digits long etc.
The unit is now in programming mode. Amber LED on the
keypad should remain permanently on. 0000 is the default
programming passcode.
The unit should exit programming mode and the amber LED
should start flashing again.
Replace ???? with your new ENGINEERS
code.

P a g e | 8
? ? 01 -
0 = start / stop toggle mode (latching)
1-99999 = seconds momentary operation
99999
or #
51=relay1
52=relay2
53=relay3
Validate
Delete a user code even if you don’t know the code…
? ? 5 ? ?? #
10=relay1
20=relay2
30=relay3 Delete code ID location to be deleted Validate
Delete an entire group of codes
? ? 0 9 99 #
10=relay1 group
20=relay2 group
30=relay3 group Super delete code Validate
Programming super user codes…
A super user code can activate any of the 3 relays
Location
0 2 ?? ? ?
4-8 digit code Validate
#
Restoring defaults
When in programming mode, you can enter the following sequence…
9 9 99 #
When the master code is forgotten….
1) Wire a push button (or replicate with wire link) across the Egress terminal and (-)GND.
2) Switch off power for 1 minute.
3) Switch ON power.
4) during the first 60 seconds, press the EG button once to enable the function.
5) Enter the following code..
8 0 08 * *
The keypad should now be in programming mode, ready to accept new data.

P a g e | 9
Using the keypad
Using the standard codes…
Once you have exited out of programming mode, simply enter the user code.
Using super user codes
?? ? ? # 1 Activate output 1
?? ? ? # 2 Activate output 2
?? ? ? # 3 Activate output 3
The Video Handset
The handset should be charged for 8 hours before use. It is recommended to give it at least 1
hour charge before range testing.

P a g e | 10
Answering Calls
1. When the intercom calls, identify the visitor on the screen.
40-80cm
2. Press the OK button to answer the call.
3. Speak clearly into the top of the handset at a distance of 10-20cm.
10cm
4. During the call press < or > to increase or decrease volume.
5. Press to activate door or gate release and press OK to end the call.
Note: The video will remain active for 1 minute after the audio call is ended.
New Voicemail
The handset will store up to 16 voicemails if missed callers decide to leave a message at the door
/ gate unit.
Press OK button to listen to a new voicemails.