AES 705 Instruction Manual

P a g e | 1
Installation & User Manual
For
605/ 7 0 5 D E C T + 2 . 4 G I n t e r c o m
Wireless Video Intercom System
Models 605AB, 605ABK,705ABK,705AB
V2
Intelligent Security & Fire Ltd.

P a g e | 2
Contents
Overview of system
…………….Pg 3
Site Survey
…………….Pg 3
605/705 Installs
…………….Pg 3
Installations
…………….Pg 3
Mounting Panels
…………….Pg 4
Power Supply
….………….Pg5
Doorstation Wiring Diagram
….………….Pg5
705 Monitor
.…………….Pg7
605 Handset
...………….Pg7
Answering Calls
…………….Pg8
Setting
…………….Pg8
Optional Audio Handset/Monitor
…………….Pg 9
Recoding
.………….Pg 9
Wiring Tip
.………….Pg 9
Basic Keypad Programming
..………….Pg 10
Full Keypad programming
…………….Pg 11
Testing
.………….Pg 13
Maintenance of the Intercom
.………….Pg 14
Troubleshooting
.………….Pg 14
Intelligent Security & Fire Ltd.

P a g e | 3
Overview of System
Please read this entire manual before attempting to install this system.
This system should only be installed by a professional automatic gate installer or access control
specialist installer.
It is recommended that the system be range tested on site BEFORE being fully installed.
Site Survey
Before installing this system, you need to be sure that the range of the system will be sufficient.
The transmitter and speech unit can be powered up, call button pressed, and then check that the
handset will ring from all areas in which it will be used.
605 Handsets Installations
Tip: For longer range installations, locate the handset close to the front of the property, near a
window if possible. Concrete walls can reduce the open air range of 350 metres by 30-50% per
wall. 705 Monitors Installations
Tip: The 705 monitor has a built-in antenna/receiver, it is best to use this for short range installs.
(see diag.1) For longer range installs, fit an external antenna (see below, check local radio
authority).
Antenna
Intercom
Antenna
External antenna
Intelligent Security & Fire Ltd.

P a g e | 4
Installation
Assuming satisfactory operation at full range, you are ready to fully install the product.
Mount the intercom at the desired height for pedestrian or car users. The camera angle
is wide at 90 degrees to cover most scenarios.
Loosen top 2 screws only
Hinge front door
Side View
Tip: Do not drill holes in the wall with the intercom in position, otherwise dust may get
around the camera window and impair the camera view.
Mounting the Antenna
Mount the antenna as
high as possible to
achieve longest range.
TIP: Antenna beam width is
approximately 40 degrees. For short
range door intercoms, ask your
distributor or dealer for an omni-pole
type antenna with 360 degree beam
angle.
Intelligent Security & Fire Ltd.

P a g e | 5
Power Supply
TIP: Most technical calls received are due to installers using CAT5 or alarm cable
to power the unit. Neither are rated to carry enough power (1.5 amp peak). Please
use following cable sizes…
Up to 2 metres (6 feet) –Use minimum 0.75mm2(18 gauge)
Up to 4 metres (12 feet) –Use minimum 1mm2(16 gauge)
Up to 8 metres (24 feet) –Use minimum 1.5mm2(14 gauge)
Excessively long
cable!!
Power supply
Call point
Mains power Power supply
Call point
Door Station Wiring Diagram
12-24vdc
+-
N/C
COM
N/O N/C N/O
egress
N/ON/C
1 2
12-24vdc
+-
N/C
COM
N/O
To antenna
From 24v dc
PSU
Relay output
Optional keypad
module
Relay 3
Relays
Relay 2 select
Intelligent Security & Fire Ltd.

P a g e | 6
705 Video Monitor Wiring and Mounting
705 Video Monitor
The Video Handset
Adjust speaker
ringtone volume
Microphone
Answer
Monitoring
Gate/Door
Trigger
The Video handset
should be charged
for 8 hours before
use. It is
recommended to
give it at least 1
hour charge before
range testing.
Adjust speaker
ringtone volume
Answer
Monitoring
Gate/Door
Trigger
Microphone
Intelligent Security & Fire Ltd.

P a g e | 7
Answering Calls
1. When the intercom calls, identify the visitor on the screen.
40-80cm
2. Press the OK button to answer the call.
3. Speak clearly into the top of the handset at a distance of 10-20cm.
10cm
4. During the call press < or > to increase or decrease volume.
5. Press to activate door or gate release and press OK to end the call.
Note: The video will remain active for 1 minute after the audio call is ended.
Settings
The following settings can be changed on both the video monitor and handset. To change any of
the following settings, put the system into monitoring mode by pressing and holding the key
for a few seconds.
1. Brightness –Adjusts screen brightness.
2. Language –English, French Or German.
3. Messages –Listen to or delete saved or older voicemails. (press KEY to delete any message).
4. Bell –Change ring tone.
5. Colour –Increase or decrease screen colour.
Use up and down arrows to navigate, and OK to select an option. Press right arrow to exit.
Intelligent Security & Fire Ltd.

P a g e | 8
Voicemail
When a call is not answered within 40 seconds, the visitor can leave a message. Once complete,
the handset will display the symbol. The unit can store up to 16 messages.
To listen to voicemail, press MENU to play. If there are more than 1 message, press and
to select the message required and press MENU to play. = Delete. Long press = delete all.
Relay Trigger Time
Press and hold the menu button for 3 seconds and the display will show “ti” .Use the up and down
arrows you can select the relay Latch time 1- 9 seconds. Press “OK” to save and arrow right to
exit Adjusting the Time
Press MENU for more than 2 seconds, and then use up and down arrow keys to set hour. Press
MENU again to cycle to minutes and adjust. Press MENU once more to end the process.
Optional Audio Monitor
Optional Audio Handset
The handset should be charged for 8 hours before use. It is recommended to give it at least 1
hour charge before range testing.
12.21
Charging
base
Power
LED
ON/OFF Vibration
ON/OFF
Voicemail
Symbol
Battery
Level
Reception
indicator
Code
Button
OK
To listen to voicemail, press OK to play. If there are more than 1 message, press and to
select the message required and press OK to play. = Delete (Relay 1). Long press = delete all
Adjust speaker
ringtone volume
Door/gate
release button 2
Microphone
Door/gate
release button 1
Answer
Change Ring Volume
Press and to increase
and decrease ring volume
and press OK to save.
Change Ring Tone
Press and the handset will
ring with its currently selected
tone.
Press and to cycle
through available ring tones
and press OK to select and
save.
Ring Another Handset
Press and the unit will
display HS1-5 depending on
how many handsets are coded.
Press and to select and
then OK to call that handset.
Voicemail
When a call is not answered
within 40 seconds, the visitor
can leave a message. Once
complete, the handset will
display the symbol. The unit
can store up to 16 messages.
Intelligent Security & Fire Ltd.

P a g e | 9
Re-coding the Handsets / Adding an Extra Handset
Occasionally a system may need re-coded when it arrives on site. If the handset does not ring
when the call button is pressed, please perform the following steps..
1. Press and hold the code button on the speech panel as shown for 3 seconds.
2. Press and hold the code button on the handset (use a fine object like ball point pen) for up to 10
seconds.
3. While holding, the handset should bleep once, then bleep again, then emit a melody
confirmation tone.
Once the melody is heard, the handset should then be working. The system should now be ready
for testing. Wiring Tips
Code Button
COM
N/O
COM
N/C
COM
N/O
Intercom board
Keypad board
Electric Gates
Gate
Controller
Magnetic
Lock
N/C
Other control
device
Separate lock
PSU
(Not supplied)
(Back of Monitor)
(Handset)
Intelligent Security & Fire Ltd.

P a g e | 10
Note: The manufacturer can only support the use, operation and functionality of the
intercom and keypad themselves. Professional wiring to door release or automatic gate
systems is the responsibility of the installer. Please consult a security integrator for
further support. Keypad overview
This keypad has 3 outputs. The diagram below shows the LED indicators which indicate
programming and relay status information.
RED when incorrect codes entered and outputs are locked out.
1 2 3
4 5 6
7 8 9
* 0 #
SLOW FLASHING - in normal standby mode.
ON in programming mode.
ON when relay 3 activated.
GREEN when output 1 activated.
RED when output 2 activated.
CLEAR when output 3 activated
FAST FLASHING –Wrong code entered / error.
TIP: After power up, as a security precaution, the keypad cannot be programmed for 60 seconds.
Once this time elapses, you may begin.
TIP: Flashing amber LED is normal standby mode.
Basic Keypad Programming
0 0 0 0 * *
Quick start guide
1) Enter programming mode (amber LED should be ON)
1 0 2 0 0 ? ?? ? #0
2) Enter a new user code...
* *
3) Exit programming mode
4) Enter the new user code to check the relay clicks.
Tip: The engineer code
must be the same length as
user codes. So if using a 6
digit engineers code, then
user codes must also be 6
digits long etc.
Intelligent Security & Fire Ltd.