aFe Power 77-83028 User manual

®
advanced FLOW engineering
Instruction Manual P/N: 77-83028
Make: Ford Model: F-150 Year: 2018-2020 Engine: V6-3.0L (td) Power Stroke

®
Page 2
THIS IS A HIGH-PERFORMANCE PRODUCT:
Do not use this product until you have carefully read the following agreement and
installation instruction. This sets forth the terms and conditions for the use of this product.
The installation of this product indicates that the BUYER has read and understands this
agreement and accepts its terms and conditions.
DISCLAIMER OF WARRANTY AND LIMITATION OF LIABILITY:
Advanced FLOW Engineering, Inc (also known as aFe or aFe POWER) and its successors,
distributors, jobbers, and dealers (hereafter “SELLER”) shall in no way be responsible for the
product’s improper use and service. It is the installer’s responsibility to check for proper
installation and if in doubt, contact the manufacturer. The SELLER assumes no liability
regarding the improper installation or misapplication of its products. BUYER acknowledges it
has had the opportunity to fully inspect the product. Accordingly, BUYER acknowledges that
the product is being sold in “AS IS/WHERE IS” condition. SELLER shall not be held
liable for special, indirect, incidental or consequential damages of any nature with respect to
the products (including, without limitation, lost profits, lost sales, loss of production, property
damage, personal injury or loss or damage resulting from interruption or failure in operation
of the products) and BUYER hereby expressly waives and disclaims all such
liability claims. The BUYER acknowledges and agrees that the disclaimer of liability
contained herein is a material term of the sale of the product and, to the fullest extent
permitted by law, BUYER shall defend, indemnify and hold SELLER harmless from any and
all claims, demands, causes of action, controversies, liabilities, fines, losses, costs and
expenses (including, but not limited to attorneys’ fees, expert witness expenses and
litigation expenses) arising from or related to SELLER’s products.
Before proceeding with the installation:
• Please read the entire instruction manual before proceeding.
• Ensure all components listed are present.
• If you are missing any of the components, call customer support at 951-493-7185.
• Do not attempt to work on your vehicle when the engine is hot.
Emission note: This product is not currently CARB exempt and is not available for
purchase in California or for use on any vehicle registered with the California Department of
Motor Vehicles.

Label Qty. Description Part Number
A 1 Module R77-83028
B 1 LED Switch 05-70013
C 1 Bypass Plug 05-70017
D 1 Harness AFE-10-242
E 2 Velcro (2 Inches) 05-01244
F 5 Cable Ties 05-60167
G 2 Double Sided Tape 07-90001
aFepower.com
Page 3
A
B
C
D
E
FG

®
Refer to Figure A for Step 1.
Step 1: Before installing the aFe POWER Module you must place your vehicle’s ECU in sleep mode. In
order to place your vehicles ECU in sleep mode you will need to do the following:
-If the engine is cold, open the hood, close the doors, lock the car and wait 30 seconds
-If the engine is warm, open the hood, close the doors, lock the car and wait 20 minutes
-If the engine is warm and you can’t wait 20 minutes, disconnect the battery
Do NOT open the doors or start the vehicle when one of the sensor is disconnected.
This could create a check engine light.
REMOVAL
Page 4
Figure A

Refer to Figure B for Steps 2-4.
Step 2: Remove the engine cover and insulation foam to gain access to the MAP and Fuel Pressure
sensors.
Step 3: Locate the MAP sensor, it is on top of the intake manifold.
Step 4: Locate the Fuel Pressure sensor, it is at the end of the fuel rail, to the left of the MAP sensor.
Figure B
Page 5
REMOVAL
aFepower.com
MAP
FUEL PRESSURE

®
Refer to Figures C for Steps 5-6.
Step 5: Disconnect the MAP sensor, by sliding the white locking tab back and pressing down on it while
sliding the connector out of the sensor.
Step 6: Locate the section of the aFe POWER harness labeled “MAP.” Plug the female connector of the
aFe POWER harness to the MAP sensor, then take the male connector of the aFe POWER
harness and connect to the female connector of the engine harness.
Figure C
Page 6
INSTALL

aFepower.com
Page 7
Refer to Figure D for Step 7.
Step 7: Check with the picture to make sure the connectors are correctly connected.
Make sure connections are fully engaged and not reversed. Usually, connectors make a
snapping sound when fully engaged.
Figure D
INSTALL

Step 8: Locate and disconnect the fuel pressure sensor connector, by pressing down on the locking tab
and sliding the connector out of the sensor.
Step 9: Locate the section of the aFe POWER harness labeled “Fuel”.” Plug the female connector of the
aFe POWER harness into the fuel pressure sensor, then take the male connector of the module
and connect to the female connector of the engine harness.
®
Page 8
Refer to Figure E for Steps 8-9.
Figure E
INSTALL

Step 10: Check with the picture to make sure the connectors are correctly connected.
Make sure connections are fully engaged and not reversed. Usually, connectors
make a snapping sound when fully engaged.
Page 9
Refer to Figure F for Step 10.
Figure F
INSTALL
aFepower.com

Page 10
Refer to Figure G for Steps 11-12.
Step 11: Connect the black ground terminal cable on the aFe POWER module to the negative battery
post by removing the 13mm nut and placing the terminal and then reinstalling the nut.
Step 12: Connect the red power terminal cable on the aFe POWER module to the positive battery post
by removing the 10mm nut and placing the terminal and then reinstalling the nut.
Figure G
INSTALL
®

aFepower.com
Page 11
Refer to Figure H for Steps 13-14.
Step 13: Secure the SCORCHER BLUE module on top of the battery, or any other desired location using
the Velcro provided. The module must be located within reach of the LED switch cable if you
are planning to use the switch.
Step 14: Connect the SCORCHER BLUE module to the harness.
Make sure connectors is fully engaged.The doors of the vehicle can now be opened to
proceed with the installation of the switch.
Figure H
INSTALL

Page 12
Refer to Figure I for Steps 15-16.
Step 15: Select the desired location of the LED switch and route the cable through the top or bottom of
the switch.
Step 16: Use the provided double sided tape to secure the LED switch in the desired location.
Figure I
INSTALL
®

aFepower.com
Page 13
Refer to Figure J Steps 17-18.
Step 17: Carefully route the switch cable behind steering wheel cover or cabin trim cover.
Step 18: Route the switch cable through firewall and into the engine bay. Follow the main harness through
the grommet into the firewall.
Figure J
INSTALL

Page 14
Refer to Figure K for Steps 19-21.
Step 19: Plug the end of the switch cable to the harness inside the engine compartment.
Step 20: Secure the wires away from any extreme heat and moving parts with the provided ties. Make
sure all connections are secured and fully engaged.
Step 21: Reinstall the foam insulation engine cover removed in Step 2.
The installation of the module itself is now completed. Keep reading the install
instruction to learn how to use all its features.
Figure K
INSTALL
®

aFepower.com
Page 15
Refer to Figure L.
(Picture is for reference)
The blue LED light will start flashing once the module is connected to the truck and the ECU on. The
blue LED will become solid if the module gets connected through Bluetooth to a device.
Figure L

Page 16
Refer to Figure S (LED Switch).
When turning on the vehicle, each LED will flash and it will stop at its last setting. The LED on the switch
represents the different level of power.
• Green LED: Stock
• Yellow LED: Sport
• Orange LED: Sport+
• Red LED: Race
Use the grey button to select the desired setting. Power adjustments can be done at any moment while
the unit is on. The LED switch can be used at the same time of the Bluetooth app.
Figure S
®

aFepower.com
Page 17
Refer to Figure T (app connection - iOS).
For iOS device, download the app from the apps store. Make sure the Bluetooth is activated on your
device. Open the app and it will automatically connect through Bluetooth to the SCORCHER BLUE
module when the vehicle and module are on. When connected, the vehicle description will show up on
top of the screen and the gauges will show current data.
The blue LED light on the module will become solid once connected to a Bluetooth device. Simply tap
on the green, yellow, orange and red button to switch between the modes.
Figure T

Page 18
Refer to Figure U (app connection- Android).
For Android device, download the app from the play store. For the first connection, go to the Bluetooth
settings of your device, turn on Bluetooth and scan for available devices. Select “aFe SCOR” and pair
with device. The vehicle needs to be on and the module connected. Once shown as paired device, open
the app on your device and it will automatically connect to the vehicle. The vehicle description will
appear on top of the screen and the gauges will show current data.
The blue LED light on the module will become solid once connected to a Bluetooth device. Simply tap
on the green, yellow, orange and red button to switch between the modes.
Figure U
®

aFepower.com
Page 19
Refer to Figure V (Custom Tuning).
The aFe POWER SCORCHER BLUE app offers the capability to custom tune the different modes. Go to
the menu on the top right corner and select “Tune”. Select the mode you would like to custom tune and
adjust the sliders at low, medium and high load. You can either write the tune or exit without writing.
Disclaimer: Custom tuning should only be performed with the ignition in the “run”
position and engine off. Configuring the tunes outside the default values may cause
drivability issues and /or check engine lights to occur.
Figure V

Page 20
Refer to Figure W (Vehicle Performance Screen).
On the gauges screen, swipe to the left to get to the vehicle performance screen.
When the vehicle is not moving, select the test you are wanting to attempt (0-60mph, ¼ mile or mile).
The app will automatically detect the movement of the vehicle and the timer will start. Once you reach
the speed or distance, the timer will stop.
If you select a new mode it will reset and you can start again. If you need to stop the test at any point, hit
the cancel button and leave the screen.
Use the aFe POWER SCORCHER BLUE app responsibly. Always drive safely and obey
traffic laws. aFe POWER is not responsible for any accidents, injuries, or property
damage that may occur during its use.
Figure W
®