aFe Power 52-10002D User manual

advanced FLOW engineering Rapid Induction Cold Air Intake System
Instruction Manual P/N: 52-10002D / 52-10002R______________________________
Make: RAM Model: 1500 Year: 2019-2021Engine: V6-3.6L

Page 2
• Please read the entire instruction manual before proceeding.
• Ensure all components listed are present.
• For technical support please call 951-493-7185.
• Ensure you have all necessary tools before proceeding.
• Do not attempt to work on your vehicle when the engine is hot.
• Retain factory parts for future use.
Label
Qty.
Description
Part Number
A1
1
Air Filter (Pro DRY S)
21-90108
A2
1
Air Filter (Pro 5R)
24-90108
B
1
Housing
05-5413020B2
C
1
Tube
05-5210002B1
D
1
Coupling, Silicone Reducer: (3-1/4” x 3-1/8”)ID x 3”L
05-01330
E
1
Seal, Trim (32” L)
05-00072
F
1
Silicone Hose, 5/8” ID (6”L)
05-01502
G
2
Clamp, #048
03-50007
H
1
Fitting, 5/8” Barb to CCV
03-50659
I
1
Grommet
03-50167
J
1
Fitting, Air Temperature Sensor
05-01454
Installation will require the following tools:
8mm nut driver, 10mm deep socket and driver, 6” driver extension
Emissions Disclaimer: This product is not currently CARB exempt and is not available for purchase in
California or for use on any vehicle registered with the California Department of Motor Vehicles.

Page 3

Page 4
Refer to Figure A for Steps 1-5
Step 1: Using an 8mm nut driver, loosen the two clamps 1 at the throttle body and factory filter housing.
Step 2: Disconnect the temperature sensor wire harness 2 .
Step 3: Using a 10mm deep socket and driver, remove the nut 3 securing the factory intake tube to the
valve cover and set aside.
Step 4: Disconnect the quick connect fitting 4 on the back side of the factory intake tube.
Step 5: Remove the factory intake tube from the vehicle.
REMOVAL
Figure A
1
1
2
3
4

Page 5
Refer to Figure B for Steps 6-7
Step 6: Using a 10mm socket and driver with extension, remove the 6x screws 5 around the factory filter
housing, and remove the cover.
Step 7: Remove the factory air filter.
REMOVAL
Figure B
5
5
5
5
5
5

Page 6
Refer to Figure C for Step 8
Step 8: Using the 6x screws 6 removed in step #6, secure your aFe POWER filter housing to the top of the
factory filter housing and tighten using a 10mm socket with extension.
Figure C
INSTALL
6
6
6
6
6
6

Page 7
Refer to Figure D for Step 9
Step 9: Install your aFe POWER air filter into the filter housing by removing the clamp, then sliding the filter
flange through the opening on the housing and pressing gently until the filter snaps into place. Place the
filter clamp loosely on the filter flange when finished.
INSTALL
Figure D

Page 8
Refer to Figure E for Step 10
Step 10: Install the supplied silicone reducer coupler 7 and clamp 8 with the smaller end on the throttle
body. Tighten the clamp using an 8mm nut driver.
INSTALL
Figure E
7
8

Page 9
Refer to Figure F for Steps 11-12
Step 11: Install the supplied male quick connect fitting 9 into the factory female fitting.
Step 12: Attach the supplied silicone hose 10 to the barbed end of the fitting.
INSTALL
Figure F
10
9

Page 10
Refer to Figure G for Step 13
Step 13: Install the supplied rubber grommet and fitting 11 into your aFe Power intake tube as shown. A
small amount of silicone grease may be used to ease the install of the fitting into the grommet.
INSTALL
Figure G
11